By default the tcp_tw_timeout value is 60 seconds. The minimum is
1 second and the maximum is 600. This setting is useful on system under
heavy tcp load.

NOTE: set the tcp_tw_timeout below 60 seconds voilates the "quiet time"
restriction, and make your system into the risk of causing some old data
to be accepted as new or new data rejected as old duplicated by some
receivers.

Link: http://web.archive.org/web/20150102003320/http://tools.ietf.org/html/rfc793Signed-off-by: NGeorge Zhang <georgezhang@linux.alibaba.com>
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Acked-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

commit ddefc033eecf23f1e8b81d0663c5db965adf5516 upstream

The commit referenced below introduced device locking around save and
restore of state for each device during a PCI bus "try" reset, making
it decidely non-"try" and prone to deadlock in the event that a device
is already locked.  Restore __pci_reset_bus() and __pci_reset_slot()
to their advertised locking semantics by pushing the save and restore
functions into the branch where the entire tree is already locked.
Extend the helper function names with "_locked" and update the comment
to reflect this calling requirement.

Fixes: b014e96d ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NZhiyuan Hou <zhiyuan2048@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

lkp-build bot reported the following link error with ipv6 disabled:

ld: net/hookers/hookers.o:(.data+0x40): undefined reference to `ipv6_specific'
ld: net/hookers/hookers.o:(.data+0x78): undefined reference to `ipv6_mapped'
ld: net/hookers/hookers.o:(.data+0xe8): undefined reference to `inet6_stream_ops'

Fixed this issue by adding IS_ENABLED(CONFIG_IPV6) check.
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NCaspar Zhang <caspar@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

Fixes: 60448d43 ("writeback: add memcg_blkcg_link tree")
Signed-off-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

read/write_cr0() are used in net/hookers.c, but they are only available
on x86 platform. Adding a depend-on fields in Kconfig to disable this
feature in other platforms.
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NCaspar Zhang <caspar@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

Wrap cgroup writeback v1 logic to prevent build errors without
CONFIG_CGROUPS or CONFIG_CGROUP_WRITEBACK.
Reported-by: Nkbuild test robot <lkp@intel.com>
Cc: Jiufei Xue <jiufei.xue@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

So far writeback control is supported for cgroup v1 interface. However
it also has some restrictions, so introduce a new kernel boot parameter
to control the behavior which is disabled by default. Users can enable
the writeback control for cgroup v1 with the command line "cgwb_v1".
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

There might have tons of files queued in the writeback, awaiting for
writing back. Unfortunately, the writeback's cgroup has been dead. In
this case, we reassociate the inode with another writeback, but we
possibly can't because the writeback associated with the dead cgroup is
the only valid one. In this case, the new writeback is allocated,
initialized and associated with the inode in the non-stopping fashion
until all data resident in the inode's page cache are flushed to disk.
It causes unnecessary high system load.

This fixes the issue by enforce moving the inode to root cgroup when the
previous binding cgroup becomes dead. With it, no more unnecessary
writebacks are created, populated and the system load decreased by about
6x in the test case we carried out:
    Without the patch: 30% system load
    With the patch:    5%  system load
Signed-off-by: Nluanshi <zhangliguang@linux.alibaba.com>
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

We have gotten a WARNNING when releasing blkcg_css:

[332489.681635] WARNING: CPU: 55 PID: 14859 at lib/list_debug.c:56 __list_del_entry+0x81/0xc0
[332489.682191] list_del corruption, ffff883e6b94d450->prev is LIST_POISON2 (dead000000000200)
......
[332489.683895] CPU: 55 PID: 14859 Comm: kworker/55:2 Tainted: G
[332489.684477] Hardware name: Inspur SA5248M4/X10DRT-PS, BIOS 4.05A
10/11/2016
[332489.685061] Workqueue: cgroup_destroy css_release_work_fn
[332489.685654]  ffffc9001d92bd28 ffffffff81380042 ffffc9001d92bd78
0000000000000000
[332489.686269]  ffffc9001d92bd68 ffffffff81088f8b 0000003800000000
ffff883e6b94d4a0
[332489.686867]  ffff883e6b94d400 ffffffff81ce8fe0 ffff88375b24f400
ffff883e6b94d4a0
[332489.687479] Call Trace:
[332489.688078]  [<ffffffff81380042>] dump_stack+0x63/0x81
[332489.688681]  [<ffffffff81088f8b>] __warn+0xcb/0xf0
[332489.689276]  [<ffffffff8108900f>] warn_slowpath_fmt+0x5f/0x80
[332489.689877]  [<ffffffff8139e7c1>] __list_del_entry+0x81/0xc0
[332489.690481]  [<ffffffff81125552>] css_release_work_fn+0x42/0x140
[332489.691090]  [<ffffffff810a2db9>] process_one_work+0x189/0x420
[332489.691693]  [<ffffffff810a309e>] worker_thread+0x4e/0x4b0
[332489.692293]  [<ffffffff810a3050>] ? process_one_work+0x420/0x420
[332489.692905]  [<ffffffff810a9616>] kthread+0xe6/0x100
[332489.693504]  [<ffffffff810a9530>] ? kthread_park+0x60/0x60
[332489.694099]  [<ffffffff817184e1>] ret_from_fork+0x41/0x50
[332489.694722] ---[ end trace 0cf869c4a5cfba87 ]---
......

This is caused by calling css_get after the css is killed by another
thread described below:

           Thread 1                       Thread 2
cgroup_rmdir
  -> kill_css
    -> percpu_ref_kill_and_confirm
      -> css_killed_ref_fn

css_killed_work_fn
  -> css_put
    -> css_release
                                        wb_get_create
					  -> find_blkcg_css
					    -> css_get
					  -> css_put
					    -> css_release (double free)
    -> css_release_workfn
      -> css_free_work_fn
       -> blkcg_css_free

When doublefree happened, it may free the memory still used by
other threads and cause a kernel panic.

Fix this by using css_tryget_online in find_blkcg_css while will return
false if the css is killed.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

Here we add a global radix tree to link memcg and blkcg that the user
attach the tasks to when using cgroup v1, which is used for writeback
cgroup.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

LVS fullnat will replace network traffic's source ip with its local ip,
and thus the backend servers cannot obtain the real client ip.

To solve this, LVS has introduced the tcp option address (TOA) to store
the essential ip address information in the last tcp ack packet of the
3-way handshake, and the backend servers need to retrieve it from the
packet header.

In this patch, we have introduced the sk_toa_data member in the sock
structure to hold the TOA information. There used to be an in-tree
module for TOA managing, whereas it has now been maintained as an
standalone module.

In this case, the toa module should register its hook function(s) using
the provided interfaces in the hookers module.

TOA in sock structure:

	__be32 sk_toa_data[16];

The hookers module only provides the sk_toa_data placeholder, and the
toa module can use this variable through the layout it needs.

Hook interfaces:

The hookers module replaces the kernel's syn_recv_sock and getname
handler with a stub that chains the toa module's hook function(s) to the
original handling function. The hookers module allows hook functions to
be installed and uninstalled in any order.

toa module:

The external toa module will be provided in separate RPM package.

[xuyu@linux.alibaba.com: amend commit log]
Signed-off-by: NGeorge Zhang <georgezhang@linux.alibaba.com>
Signed-off-by: NXu Yu <xuyu@linux.alibaba.com>
Reviewed-by: NCaspar Zhang <caspar@linux.alibaba.com>

commit 1f23816b8eb8fdc39990abe166c10a18c16f6b21 upstream.

In commit 88c85538, "virtio-blk: add discard and write zeroes features
to specification" (https://github.com/oasis-tcs/virtio-spec), the virtio
block specification has been extended to add VIRTIO_BLK_T_DISCARD and
VIRTIO_BLK_T_WRITE_ZEROES commands.  This patch enables support for
discard and write zeroes in the virtio-blk driver when the device
advertises the corresponding features, VIRTIO_BLK_F_DISCARD and
VIRTIO_BLK_F_WRITE_ZEROES.
Signed-off-by: NChangpeng Liu <changpeng.liu@intel.com>
Signed-off-by: NDaniel Verkamp <dverkamp@chromium.org>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NLiu Bo <bo.liu@linux.alibaba.com>
Acked-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

Unstable tsc will trigger clocksource watchdog and disable itself, as a
result other clocksource will be elected as the current clocksource
which will result in performace issue on our servers.

RHEL7 also disabled this feature for some issues, see changelog:
[x86] disable clocksource watchdog (Prarit Bhargava) [914709]
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Acked-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

This reverts commit 76d3b851.

The returned value for check_tsc_warp() is useless now, remove it.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

This reverts commit cc4db268.

When we do hot-add and enable vCPU, the time inside the VM jumps and
then VM stucks.
The dmesg shows like this:
[   48.402948] CPU2 has been hot-added
[   48.413774] smpboot: Booting Node 0 Processor 2 APIC 0x2
[   48.415155] kvm-clock: cpu 2, msr 6b615081, secondary cpu clock
[   48.453690] TSC ADJUST compensate: CPU2 observed 139318776350 warp.  Adjust: 139318776350
[  102.060874] clocksource: timekeeping watchdog on CPU0: Marking clocksource 'tsc' as unstable because the skew is too large:
[  102.060874] clocksource:                       'kvm-clock' wd_now: 1cb1cfc4bf8 wd_last: 1be9588f1fe mask: ffffffffffffffff
[  102.060874] clocksource:                       'tsc' cs_now: 207d794f7e cs_last: 205a32697a mask: ffffffffffffffff
[  102.060874] tsc: Marking TSC unstable due to clocksource watchdog
[  102.070188] KVM setup async PF for cpu 2
[  102.071461] kvm-stealtime: cpu 2, msr 13ba95000
[  102.074530] Will online and init hotplugged CPU: 2

This is because the TSC for the newly added VCPU is initialized to 0
while others are ahead. Guest will do the TSC ADJUST compensate and
cause the time jumps.

Commit bd8fab39("KVM: x86: fix maintaining of kvm_clock stability
on guest CPU hotplug") can fix this problem.  However, the host kernel
version may be older, so do not ajust TSC if sync test fails, just mark
it unstable.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

ECI may have an use case that configuring each device mapper disk
throttling policy just under root blkio cgroup, but actually using them
in different containers.
Since hierarchical throttling is now only supported on cgroup v2 and ECI
uses cgroup v1, so we have to enable hierarchical throttling on cgroup
v1.
This is ported from redhat 7u, and a year ago Jiufei already ported it
to alikernel 4.9 as well. So I think this change should be acceptable.
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

Prior to xdragon platform 20181230 release (e.g. 0930 release),
vring_use_dma_api() is required to return 'true' unconditionally.

Introduce a new kernel boot parameter called "vring_force_dma_api" to
control the behavior, boot xdragon host with "vring_force_dma_api"
command line to make ENI hotplug work, so that normal ECS hosts keep the
original behavior.
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: NEryu Guan <eguan@linux.alibaba.com>

Cherry-pick from clear-linux patches:
https://github.com/clearlinux-pkgs/linux-kvm/0104-give-rdrand-some-credit.patch

try to credit rdrand/rdseed with some entropy

In VMs but even modern hardware, we're super starved for entropy, and while we can
and do wear a tin foil hat, it's very hard to argue that
rdrand and rdtsc add zero entropy.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

Cherry-pick from kata-container patches:
https://github.com/kata-containers/packaging/tree/master/kernel/patches/0001-NO-UPSTREAM-9P-always-use-cached-inode-to-fill-in-v9.patch

So that if in cache=none mode, we don't have to lookup server that
might not support open-unlink-fstat operation.

fixes https://github.com/01org/cc-oci-runtime/issues/47
fixes https://github.com/01org/cc-oci-runtime/issues/1062Signed-off-by: NJulio Montes <julio.montes@intel.com>
Signed-off-by: NPeng Tao <bergwolf@gmail.com>
Signed-off-by: NEryu Guan <eguan@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

Cherry-pick from kata-container patches:
https://github.com/kata-containers/packaging/tree/master/kernel/patches/0002-Compile-in-evged-always.patch

We need evged for NEMU (and in general for hw reduced)

The config option cannot be set normally since it breaks all
regular systems, and hardware reduced is really a runtime choice.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NEryu Guan <eguan@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

commit f456767d3391e9f7d9d25a2e7241d75676dc19da upstream.

Add new code to count canceled pending cluster reservations on bigalloc
file systems and to reduce the cluster reservation count on all file
systems using delayed allocation.  This replaces old code in
ext4_da_page_release_reservations that was incorrect.
Signed-off-by: NEric Whitney <enwlinux@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

commit 9fe671496b6c286f9033aedfc1718d67721da0ae upstream.

Modify ext4_ext_remove_space() and the code it calls to correct the
reserved cluster count for pending reservations (delayed allocated
clusters shared with allocated blocks) when a block range is removed
from the extent tree.  Pending reservations may be found for the clusters
at the ends of written or unwritten extents when a block range is removed.
If a physical cluster at the end of an extent is freed, it's necessary
to increment the reserved cluster count to maintain correct accounting
if the corresponding logical cluster is shared with at least one
delayed and unwritten extent as found in the extents status tree.

Add a new function, ext4_rereserve_cluster(), to reapply a reservation
on a delayed allocated cluster sharing blocks with a freed allocated
cluster.  To avoid ENOSPC on reservation, a flag is applied to
ext4_free_blocks() to briefly defer updating the freeclusters counter
when an allocated cluster is freed.  This prevents another thread
from allocating the freed block before the reservation can be reapplied.

Redefine the partial cluster object as a struct to carry more state
information and to clarify the code using it.

Adjust the conditional code structure in ext4_ext_remove_space to
reduce the indentation level in the main body of the code to improve
readability.
Signed-off-by: NEric Whitney <enwlinux@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

commit b6bf9171ef5c37b66d446378ba63af5339a56a97 upstream.

Ext4 does not always reduce the reserved cluster count by the number
of clusters allocated when mapping a delayed extent.  It sometimes
adds back one or more clusters after allocation if delalloc blocks
adjacent to the range allocated by ext4_ext_map_blocks() share the
clusters newly allocated for that range.  However, this overcounts
the number of clusters needed to satisfy future mapping requests
(holding one or more reservations for clusters that have already been
allocated) and premature ENOSPC and quota failures, etc., result.

Ext4 also does not reduce the reserved cluster count when allocating
clusters for non-delayed allocated writes that have previously been
reserved for delayed writes.  This also results in overcounts.

To make it possible to handle reserved cluster accounting for
fallocated regions in the same manner as used for other non-delayed
writes, do the reserved cluster accounting for them at the time of
allocation.  In the current code, this is only done later when a
delayed extent sharing the fallocated region is finally mapped.

Address comment correcting handling of unsigned long long constant
from Jan Kara's review of RFC version of this patch.
Signed-off-by: NEric Whitney <enwlinux@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

commit 0b02f4c0d6d9e2c611dfbdd4317193e9dca740e6 upstream.

The code in ext4_da_map_blocks sometimes reserves space for more
delayed allocated clusters than it should, resulting in premature
ENOSPC, exceeded quota, and inaccurate free space reporting.

Fix this by checking for written and unwritten blocks shared in the
same cluster with the newly delayed allocated block.  A cluster
reservation should not be made for a cluster for which physical space
has already been allocated.
Signed-off-by: NEric Whitney <enwlinux@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

commit 1dc0aa46e74a3366e12f426b7caaca477853e9c3 upstream.

Add new pending reservation mechanism to help manage reserved cluster
accounting.  Its primary function is to avoid the need to read extents
from the disk when invalidating pages as a result of a truncate, punch
hole, or collapse range operation.
Signed-off-by: NEric Whitney <enwlinux@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

commit ad431025aecda85d3ebef5e4a3aca5c1c681d0c7 upstream.

Ext4 contains a few functions that are used to search for delayed
extents or blocks in the extents status tree.  Rather than duplicate
code to add new functions to search for extents with different status
values, such as written or a combination of delayed and unwritten,
generalize the existing code to search for caller-specified extents
status values.  Also, move this code into extents_status.c where it
is better associated with the data structures it operates upon, and
where it can be more readily used to implement new extents status tree
functions that might want a broader scope for i_es_lock.

Three missing static specifiers in RFC version of patch reported and
fixed by Fengguang Wu <fengguang.wu@intel.com>.
Signed-off-by: NEric Whitney <enwlinux@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>

commit 057d476fff778f1d3b9f861fdb5437ea1a3cfc99 upstream.

A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.

When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.

If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.

Example case:
usb_runtime_suspend() # because all ports still show suspended U3
  usb_suspend_both()
    hub_suspend();   # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
  handle_port_status()
    clear bus_state->port_remote_wakeup
    usb_wakeup_notification()
      sets hub->wakeup_bits;
        kick_hub_wq()
<== END INTERRUPT
      hcd_bus_suspend()
        xhci_bus_suspend() # success as port_remote_wakeup bits cleared

Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.

Issue rootcaused by Chiasheng Lee

Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: NLee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 008037d4d972c9c47b273e40e52ae34f9d9e33e7 upstream.

Shift and mask were reversed.  Noticed by chance.
Tested-by: NMeelis Roos <mroos@linux.ee>
Reviewed-by: NMichel Dänzer <mdaenzer@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 58e39a2ce4be08162c0368030cdc405f7fd849aa upstream.

When a port sends PLOGI, discovery state should be changed to login
pending, otherwise RELOGIN_NEEDED bit is set in
qla24xx_handle_plogi_done_event(). RELOGIN_NEEDED triggers another PLOGI,
and it never goes out of the loop until login timer expires.

Fixes: 8777e431 ("scsi: qla2xxx: Migrate NVME N2N handling into state machine")
Fixes: 8b5292bcfcacf ("scsi: qla2xxx: Fix Relogin to prevent modifying scan_state flag")
Cc: Quinn Tran <qutran@marvell.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191125165702.1013-6-r.bolshakov@yadro.comAcked-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5480e299b5ae57956af01d4839c9fc88a465eeab upstream.

Some time ago the block layer was modified such that timeout handlers are
called from thread context instead of interrupt context. Make it safe to
run the iSCSI timeout handler in thread context. This patch fixes the
following lockdep complaint:

================================
WARNING: inconsistent lock state
5.5.1-dbg+ #11 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/7:1H/206 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff88802d9827e8 (&(&session->frwd_lock)->rlock){+.?.}, at: iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
{IN-SOFTIRQ-W} state was registered at:
  lock_acquire+0x106/0x240
  _raw_spin_lock+0x38/0x50
  iscsi_check_transport_timeouts+0x3e/0x210 [libiscsi]
  call_timer_fn+0x132/0x470
  __run_timers.part.0+0x39f/0x5b0
  run_timer_softirq+0x63/0xc0
  __do_softirq+0x12d/0x5fd
  irq_exit+0xb3/0x110
  smp_apic_timer_interrupt+0x131/0x3d0
  apic_timer_interrupt+0xf/0x20
  default_idle+0x31/0x230
  arch_cpu_idle+0x13/0x20
  default_idle_call+0x53/0x60
  do_idle+0x38a/0x3f0
  cpu_startup_entry+0x24/0x30
  start_secondary+0x222/0x290
  secondary_startup_64+0xa4/0xb0
irq event stamp: 1383705
hardirqs last  enabled at (1383705): [<ffffffff81aace5c>] _raw_spin_unlock_irq+0x2c/0x50
hardirqs last disabled at (1383704): [<ffffffff81aacb98>] _raw_spin_lock_irq+0x18/0x50
softirqs last  enabled at (1383690): [<ffffffffa0e2efea>] iscsi_queuecommand+0x76a/0xa20 [libiscsi]
softirqs last disabled at (1383682): [<ffffffffa0e2e998>] iscsi_queuecommand+0x118/0xa20 [libiscsi]

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&session->frwd_lock)->rlock);
  <Interrupt>
    lock(&(&session->frwd_lock)->rlock);

 *** DEADLOCK ***

2 locks held by kworker/7:1H/206:
 #0: ffff8880d57bf928 ((wq_completion)kblockd){+.+.}, at: process_one_work+0x472/0xab0
 #1: ffff88802b9c7de8 ((work_completion)(&q->timeout_work)){+.+.}, at: process_one_work+0x476/0xab0

stack backtrace:
CPU: 7 PID: 206 Comm: kworker/7:1H Not tainted 5.5.1-dbg+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
 dump_stack+0xa5/0xe6
 print_usage_bug.cold+0x232/0x23b
 mark_lock+0x8dc/0xa70
 __lock_acquire+0xcea/0x2af0
 lock_acquire+0x106/0x240
 _raw_spin_lock+0x38/0x50
 iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
 scsi_times_out+0xf4/0x440 [scsi_mod]
 scsi_timeout+0x1d/0x20 [scsi_mod]
 blk_mq_check_expired+0x365/0x3a0
 bt_iter+0xd6/0xf0
 blk_mq_queue_tag_busy_iter+0x3de/0x650
 blk_mq_timeout_work+0x1af/0x380
 process_one_work+0x56d/0xab0
 worker_thread+0x7a/0x5d0
 kthread+0x1bc/0x210
 ret_from_fork+0x24/0x30

Fixes: 287922eb ("block: defer timeouts to a workqueue")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191209173457.187370-1-bvanassche@acm.orgSigned-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NLee Duncan <lduncan@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 474e559567fa631dea8fb8407ab1b6090c903755 upstream.

We got the following warnings from thin_check during thin-pool setup:

  $ thin_check /dev/vdb
  examining superblock
  examining devices tree
    missing devices: [1, 84]
      too few entries in btree_node: 41, expected at least 42 (block 138, max_entries = 126)
  examining mapping tree

The phenomenon is the number of entries in one node of details_info tree is
less than (max_entries / 3). And it can be easily reproduced by the following
procedures:

  $ new a thin pool
  $ presume the max entries of details_info tree is 126
  $ new 127 thin devices (e.g. 1~127) to make the root node being full
    and then split
  $ remove the first 43 (e.g. 1~43) thin devices to make the children
    reblance repeatedly
  $ stop the thin pool
  $ thin_check

The root cause is that the B-tree removal procedure in __rebalance2()
doesn't guarantee the invariance: the minimal number of entries in
non-root node should be >= (max_entries / 3).

Simply fix the problem by increasing the rebalance threshold to
make sure the number of entries in each child will be greater
than or equal to (max_entries / 3 + 1), so no matter which
child is used for removal, the number will still be valid.

Cc: stable@vger.kernel.org
Signed-off-by: NHou Tao <houtao1@huawei.com>
Acked-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dbaf971c9cdf10843071a60dcafc1aaab3162354 upstream.

Removes the branching for edge-case where no SCSI device handler
exists.  The __map_bio_fast() method was far too limited, by only
selecting a new pathgroup or path IFF there was a path failure, fix this
be eliminating it in favor of __map_bio().  __map_bio()'s extra SCSI
device handler specific MPATHF_PG_INIT_REQUIRED test is not in the fast
path anyway.

This change restores full path selector functionality for bio-based
configurations that don't haave a SCSI device handler.  But it should be
noted that the path selectors do have an impact on performance for
certain networks that are extremely fast (and don't require frequent
switching).

Fixes: 8d47e659 ("dm mpath: remove unnecessary NVMe branching in favor of scsi_dh checks")
Cc: stable@vger.kernel.org
Reported-by: NDrew Hastings <dhastings@crucialwebhost.com>
Suggested-by: NMartin Wilck <mwilck@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 43cb86799ff03e9819c07f37f72f80f8246ad7ed upstream.

With commit 222ec161 ("drm: Add aspect ratio parsing in DRM
layer") the drm core started honoring the picture_aspect_ratio field
when comparing two drm_display_modes. Prior to that it was ignored.
When the CVBS encoder driver was initially submitted there was no aspect
ratio check.

Switch from drm_mode_equal() to drm_mode_match() without
DRM_MODE_MATCH_ASPECT_RATIO to fix "kmscube" and X.org output using the
CVBS connector. When (for example) kmscube sets the output mode when
using the CVBS connector it passes HDMI_PICTURE_ASPECT_NONE, making the
drm_mode_equal() fail as it include the aspect ratio.

Prior to this patch kmscube reported:
  failed to set mode: Invalid argument

The CVBS mode checking in the sun4i (drivers/gpu/drm/sun4i/sun4i_tv.c
sun4i_tv_mode_to_drm_mode) and ZTE (drivers/gpu/drm/zte/zx_tvenc.c
tvenc_mode_{pal,ntsc}) drivers don't set the "picture_aspect_ratio" at
all. The Meson VPU driver does not rely on the aspect ratio for the CVBS
output so we can safely decouple it from the hdmi_picture_aspect
setting.

Cc: <stable@vger.kernel.org>
Fixes: 222ec161 ("drm: Add aspect ratio parsing in DRM layer")
Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
[narmstrong: squashed with drm: meson: venc: cvbs: deduplicate the meson_cvbs_mode lookup code]
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191208171832.1064772-3-martin.blumenstingl@googlemail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6645d42d79d33e8a9fe262660a75d5f4556bbea9 upstream.

In the implementation of sync_file_merge() the allocated sync_file is
leaked if number of fences overflows. Release sync_file by goto err.

Fixes: a02b9dc9 ("dma-buf/sync_file: refactor fence storage in struct sync_file")
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191122220957.30427-1-navid.emamdoost@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d567fb8819162099035e546b11a736e29c2af0ea upstream.

Since irq_bypass_register_producer() is called after request_irq(), we
should do tear-down in reverse order: irq_bypass_unregister_producer()
then free_irq().

Specifically free_irq() may release resources required by the
irqbypass del_producer() callback.  Notably an example provided by
Marc Zyngier on arm64 with GICv4 that he indicates has the potential
to wedge the hardware:

 free_irq(irq)
   __free_irq(irq)
     irq_domain_deactivate_irq(irq)
       its_irq_domain_deactivate()
         [unmap the VLPI from the ITS]

 kvm_arch_irq_bypass_del_producer(cons, prod)
   kvm_vgic_v4_unset_forwarding(kvm, irq, ...)
     its_unmap_vlpi(irq)
       [Unmap the VLPI from the ITS (again), remap the original LPI]
Signed-off-by: NJiang Yi <giangyi@amazon.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 6d7425f1 ("vfio: Register/unregister irq_bypass_producer")
Link: https://lore.kernel.org/kvm/20191127164910.15888-1-giangyi@amazon.comReviewed-by: NMarc Zyngier <maz@kernel.org>
Reviewed-by: NEric Auger <eric.auger@redhat.com>
[aw: commit log]
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d70f7d31a9e2088e8a507194354d41ea10062994 upstream.

There is an unfortunate typo in the code that results in writing to
FLOW_CTLR_HALT instead of FLOW_CTLR_CSR.

Cc: <stable@vger.kernel.org>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NDmitry Osipenko <digetx@gmail.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d60d0cff4ab01255b25375425745c3cff69558ad upstream.

fin_pll is the parent of clock-controller@7e00f000, specify
the dependency to ensure proper initialization order of clock
providers.

without this patch:
[    0.000000] S3C6410 clocks: apll = 0, mpll = 0
[    0.000000]  epll = 0, arm_clk = 0

with this patch:
[    0.000000] S3C6410 clocks: apll = 532000000, mpll = 532000000
[    0.000000]  epll = 24000000, arm_clk = 532000000

Cc: <stable@vger.kernel.org>
Fixes: 3f6d439f ("clk: reverse default clk provider initialization order in of_clk_init()")
Signed-off-by: NLihua Yao <ylhuajnu@outlook.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9150c3adbf24d77cfba37f03639d4a908ca4ac25 upstream.

If Close command is interrupted before sending a request
to the server the client ends up leaking an open file
handle. This wastes server resources and can potentially
block applications that try to remove the file or any
directory containing this file.

Fix this by putting the close command into a worker queue,
so another thread retries it later.

Cc: Stable <stable@vger.kernel.org>
Tested-by: NFrank Sorenson <sorenson@redhat.com>
Reviewed-by: NRonnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: NPavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>