In commit 7d23e3c3 ("drm/i915: Cleaning up intel_dp_hpd_pulse") some
much needed clean-up was done, but unfortunately part of the change
broke DP MST.  The real issue was setting the connector state to
disconnected in the MST case, which is good, but the code then (after
a goto) checks if the connector state is not connected and shuts down
MST if this is the case, which is bad.  With this change both SST and
MST seem to be happy.

v2: Add removed check further up in the function to be sure that MST
    is shut down when we lose the link. (Ander)

Fixes: commit 7d23e3c3 ("drm/i915: Cleaning up intel_dp_hpd_pulse")
cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: NJim Bride <jim.bride@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: NLyude <cpaul@redhat.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460394684-7036-1-git-send-email-jim.bride@linux.intel.com

Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.

v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

We need to kunmap pt_vaddr and not pt itself, otherwise we end up
mapping a bunch of pages without ever unmapping them.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Fixes: d1c54acd ("drm/i915/gtt: Introduce kmap|kunmap for dma page")
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460476663-24890-4-git-send-email-matthew.auld@intel.com

The power cycle delay starts _after_ turning off the panel power. Do the
msleep after frobbing the pmic panel power gpio.

Also toss in a FIXME about optimizing away needless waits.

Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: fc45e821 ("drm/i915: Use the CRC gpio for panel enable/disable")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460996271-29795-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>

Currently we're trying to define HSW/BDW power wells by what's not
included. Let's do it the other way around, so that you can actually
tell when the power well would get enabled. This will also allow us to
add new power domains without accidentally adding it to the HSW/BDW
display power domains.

The current set of domains looks rather buggy even:
- POWER_DOMAIN_MODESET is included in the display power well needlessly
- DDI-B to DDI-E were not part of the display power well when they
  should be

So let's fix that up while at it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Currently we're using POWER_DOMAIN_MASK as the power domains for the
display power well on VLV/CHV. That includes all power domains even
though the disp2d/pipe-a power well is not needed for a lot of things.
Let's reduce these to what we actually need.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The always-on well is the same as runtime PM, so we should just
"enable" it for any power domain. Throw out the usless
FOO_ALWAYS_ON_DOMAINS defines and just use POWER_DOMAIN_MASK.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

intel_pipe_will_have_type() doesn't just look at the passied in
pipe_config, instead it expects there to be a full atomic state behind
it. Obviously that won't go so well when vlv_force_pll_on() just uses a
temp pipe_config. Fix things by using pipe_config->has_dsi_encoder
instead intel_pipe_will_have_type(INTEL_OUTPUT_DSI) to check if we need
to actually enable the DPLL.

Here's an example oops for reference:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: [<ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
PGD 7acda067 PUD 72696067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: i915 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm intel_gtt agpgart netconsole psmouse atkbd iTCO_wdt libps2 coretemp hwmon efi_pstore intel_rapl punit_atom_debug efivars pcspkr i2c_i801 r8169 lpc_ich mii processor_thermal_device snd_soc_rt5670 intel_soc_dts_iosf snd_soc_rl6231 i2c_hid hid snd_intel_sst_acpi snd_intel_sst_core snd_soc_sst_mfld_platform snd_soc_sst_match snd_soc_core i8042 serio snd_compress snd_pcm snd_timer snd i2c_designware_platform sdhci_acpi i2c_designware_core soundcore sdhci pwm_lpss_platform mmc_core pwm_lpss spi_pxa2xx_platform evdev int3403_thermal int3400_thermal int340x_thermal_zone acpi_thermal_rel sch_fq_codel ip_tables x_tables ipv6 autofs4
CPU: 3 PID: 290 Comm: Xorg Tainted: G     U          4.6.0-rc4-bsw+ #2876
Hardware name: Intel Corporation CHERRYVIEW C0 PLATFORM/Braswell CRB, BIOS BRAS.X64.X088.R00.1510270350 10/27/2015
task: ffff88007a8dd200 ti: ffff880173ac4000 task.ti: ffff880173ac4000
RIP: 0010:[<ffffffffa0389a5b>]  [<ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
RSP: 0018:ffff880173ac7928  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880176594000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000009 RDI: ffff880176594000
RBP: ffff880173ac7930 R08: 0000000000019290 R09: 0000000000000000
R10: ffff880173ac7890 R11: 00000000000080cf R12: ffff88017fbd4000
R13: ffffffffa03e3c44 R14: ffff88007492c000 R15: ffff88007492c000
FS:  00007ff8936a6940(0000) GS:ffff88017ef80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000030 CR3: 0000000177e08000 CR4: 00000000001006e0
Stack:
 ffff880176594000 ffff880173ac7948 ffffffffa0389b42 ffff880176594000
 ffff880173ac7978 ffffffffa0396e02 ffff8801765b0000 ffff88007af660d8
 0000000000000000 0000000000000004 ffff880173ac79c0 ffffffffa03b6b64
Call Trace:
 [<ffffffffa0389b42>] chv_compute_dpll.isra.39+0x33/0x55 [i915]
 [<ffffffffa0396e02>] vlv_force_pll_on+0x80/0xc6 [i915]
 [<ffffffffa03b6b64>] vlv_power_sequencer_pipe+0x29b/0x3dd [i915]
 [<ffffffffa03b6cd4>] _pp_stat_reg+0x2e/0x38 [i915]
 [<ffffffffa03b6dc1>] wait_panel_status+0x4c/0x1ec [i915]
 [<ffffffffa03b6fcb>] wait_panel_power_cycle+0x6a/0xb4 [i915]
 [<ffffffffa03b70da>] edp_panel_vdd_on+0xc5/0x1d1 [i915]
 [<ffffffffa03b861b>] intel_dp_aux_ch+0x55/0x572 [i915]
 [<ffffffff810af5c8>] ? mark_held_locks+0x5d/0x74
 [<ffffffff81518e61>] ? mutex_lock_nested+0x321/0x346
 [<ffffffff81094007>] ? preempt_count_sub+0xf2/0x102
 [<ffffffffa03b8cb4>] intel_dp_aux_transfer+0x17c/0x1b5 [i915]
 [<ffffffffa03028ef>] drm_dp_dpcd_access+0x62/0xed [drm_kms_helper]
 [<ffffffffa0302995>] drm_dp_dpcd_read+0x1b/0x1f [drm_kms_helper]
 [<ffffffffa03b5147>] intel_dp_dpcd_read_wake+0x31/0x69 [i915]
 [<ffffffffa03bb36a>] intel_dp_long_pulse+0x15f/0x5ed [i915]
 [<ffffffffa03bbb09>] intel_dp_detect+0x79/0x95 [i915]
 [<ffffffffa030340e>] drm_helper_probe_single_connector_modes+0xc7/0x3db [drm_kms_helper]
 [<ffffffffa029de23>] drm_mode_getconnector+0xe9/0x333 [drm]
 [<ffffffff810b1cfb>] ? lock_acquire+0x137/0x1df
 [<ffffffffa0292364>] drm_ioctl+0x266/0x3ae [drm]
 [<ffffffffa029dd3a>] ? drm_mode_getcrtc+0x126/0x126 [drm]
 [<ffffffff811af082>] vfs_ioctl+0x18/0x34
 [<ffffffff811af682>] do_vfs_ioctl+0x547/0x5fe
 [<ffffffff811b9acb>] ? __fget_light+0x62/0x71
 [<ffffffff811af77c>] SyS_ioctl+0x43/0x61
 [<ffffffff81001a82>] do_syscall_64+0x63/0xf8
 [<ffffffff8151bc9a>] entry_SYSCALL64_slow_path+0x25/0x25
Code: 35 00 40 a0 e8 97 4b ce e0 b8 17 00 00 00 5d c3 b8 17 00 00 00 c3 0f 1f 44 00 00 55 31 c0 31 d2 48 89 e5 53 48 8b 8f e8 01 00 00 <44> 8b 49 30 41 39 c1 7e 2d 4c 8b 51 38 4c 8b 41 40 49 83 3c c2
RIP  [<ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
 RSP <ffff880173ac7928>
CR2: 0000000000000030

The regressing patch wasn't exactly new (as in first posted more than
six months ago), so I'm a bit baffled how I didn't manage to hit this
myself so far.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Marius Vlad <marius.c.vlad@intel.com>
Reported-by: NMarius Vlad <marius.c.vlad@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94995
Fixes: cd2d34d9 ("drm/i915: Setup DPLL/DPLLMD for DSI too on VLV/CHV")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461000844-20543-1-git-send-email-ville.syrjala@linux.intel.comTested-by: NMarius Vlad <marius.c.vlad@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>

While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.

v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
  opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com

The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:

commit 6d93c0c4 ("drm/i915: fix VDD state tracking after system
resume")

At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).

While at it remove an unnecessary function call indirection.

This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com

During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.

This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.

v2:
- Add a code comment about the relation of this fix to the freeze/thaw
  vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
  and device enable calls. (Chris)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: stable@vger.kernel.org
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460979954-14503-1-git-send-email-imre.deak@intel.com

If system resume fails, this may lead to a runtime PM wake reference
underflow used for runtime PM state checking.

Fixes: 1f814dac ("drm/i915: add support for checking if we hold an RPM reference")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-2-git-send-email-imre.deak@intel.com

The workaround added in
commit c6782b76 ("drm/i915/gen9: Reset secondary power well
requests left on by DMC/KVMR")
needs to be applied on Kabylake too as shown by the corresponding
timeout errors about power well 1 and MISC IO power well disabling in
the latest CI run.

CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460748778-4484-1-git-send-email-imre.deak@intel.com

When a vblank wait times out in intel_atomic_wait_for_vblanks() we just
get a cryptic 'WARN_ON(!ret)' backtrace in dmesg. Repace it with
something that tells you what actually happened.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460978973-24945-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: NRafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes: 5008e874 ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.ukAcked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Due to "some hardware limitation" the DPI enable bit in port C control
register does not get set on VLV. As a workaround we check the status in
pipe B conf register instead. The workaround was added in

commit c0beefd2
Author: Gaurav K Singh <gaurav.k.singh@intel.com>
Date:   Tue Dec 9 10:59:20 2014 +0530

    drm/i915: Software workaround for getting the HW status of DSI Port C on BYT

Empirical evidence (on Surface 3 with DSI on port C per VBT) shows that
this is the case also on CHV, so extend the workaround to CHV. We still
have the device ready register check in place, so this should not get
confused with e.g. HDMI on pipe B.

This fixes a number of state checker warnings on CHV DSI port C.

Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460724451-13810-1-git-send-email-jani.nikula@intel.com

Show a total and purgeable number of pin mapped objects
and their total and purgeable size.

Example output (new stat prefixed with a star):

  # cat i915_gem_objects
  19920 objects, 289243136 bytes
  19920 [18466] objects, 288714752 [267911168] bytes in gtt
    0 [0] active objects, 0 [0] bytes
    19917 [18466] inactive objects, 288714752 [267911168] bytes
  0 unbound objects, 0 bytes
  0 purgeable objects, 0 bytes
  1 pinned mappable objects, 3145728 bytes
  0 fault mappable objects, 0 bytes
* 19914 [0] pin mapped objects, 285560832 [0] bytes [purgeable]
  4294967296 [268435456] gtt total
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460716493-27826-1-git-send-email-tvrtko.ursulin@linux.intel.com

Reflect the status of obj->mapping as added with the
i915_gem_object_pin_map API.

'M' was chosen to designate the pin mapped status.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

We don't have a LVDS_BORDER_ENABLE type of bit for either eDP or DSI,
and just trying to frob the display timings to include borders results
in a corrupted picture. So reject the 'Center' scaling mode on GMCH
platforms for eDP and DSI.

TODO: Should really filter out the unsupported modes from the prop,
but that would be fairly invasive since the prop is now created and
stored by drm core. So leave it for a rainy day.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-6-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Add the scaling mode property to DSI connectors, handle changes in the
property value, and compute the panel fitter state during
.compute_config().

v2: Handle BXT as well
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-5-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Fold the DSI PLL configuration functions into the DSI PLL
enable functions since they are small and not called from anywhere else.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-4-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Compute the DSI PLL parameters during .compute_config() rather than
.pre_pll_enable() so that we can fail gracefully if we can't find
suitable parameters.

In order to do that we need to store the DSI PLL parameters in
pipe_config.

v2: Handle BXT too
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-3-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Set up DPLL and DPLL_MD even when driving DSI output on VLV/CHV. While
the DPLL isn't used to provide the clock we still need the refclock, and
it appears that the pixel repeat factor also has an effect on DSI
output. So set up eveyrhing in DPLL and DPLL_MD as we would do for
DP/HDMI/VGA, but don't actually enable the DPLL or configure the
dividers via DPIO.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Tested-by: NJani Nikula <jani.nikula@intel.com>

This patch is to correct one thing in this commit:

commit 25a56705
Author: Dongwon Kim <dongwon.kim@intel.com>
Date:   Wed Mar 16 18:06:13 2016 -0700

    drm/i915/bxt: Reversed polarity of PORT_PLL_REF_SEL bit

This reversed bit polarity is actually common
for all BXT and APL SoCs. Therefore, revision checking
in the original commit should be removed to make
the bit set regardless of revision ID of GFX block.
Signed-off-by: NDongwon Kim <dongwon.kim@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460673463-14453-1-git-send-email-dongwon.kim@intel.com

With the preceding fixes runtime PM should be functional, I could
runtime suspend/resume the device without problems.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-17-git-send-email-imre.deak@intel.com

With the preceding fixes power well support should be functional on
Broxton, I could enter/exit DC5 without problems.

This reverts commit 18024199.

CC: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-16-git-send-email-imre.deak@intel.com

I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.

v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
  incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com

If BIOS has already programmed and enabled a PHY, don't reprogram it as
that may interfere with the currently active outputs. A follow-up patch
will add state verification, so we can catch any misconfiguration on
BIOS's behalf.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-14-git-send-email-imre.deak@intel.com

When determining whether CDCLK is enabled by BIOS and so we should skip
reprogramming it, we didn't check the related DBUF power request and
state. In theory BIOS could enable one without the other so check for
this case and reprogram things if something is amiss.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-13-git-send-email-imre.deak@intel.com

Power well 1 is managed by the DMC firmware so don't toggle it on-demand
from the driver. This means we need to follow the BSpec display
initialization sequence during driver loading and resuming (both system
and runtime) and enable power well 1 only once there. Afterwards DMC
will toggle power well 1 whenever entering/exiting DC5.

For this to work we also need to do away getting the PLL power domain,
since that just kept runtime PM disabled for good.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-12-git-send-email-imre.deak@intel.com

The power-down step logically belongs to the individual PHY uninit
sequence so move it there. The only functional change is that we will
power down now PHY 1 separately before PHY 0 and preserve the other bits
in the register which are defined as reserved.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-11-git-send-email-imre.deak@intel.com

For internal APIs passing dev_priv is preferred to reduce indirections,
so convert over a few DDI PHY, CDCLK helpers.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-10-git-send-email-imre.deak@intel.com

On Broxton we need to enable/disable power well 1 during the init/unit
display sequence similarly to Skylake/Kabylake. The code for this will
be added in a follow-up patch, but to prepare for that unexport
skl_pw1_misc_io_init(). It's a simple function called only from a single
place and having it inlined in the Skylake display core init/unit
functions will make it easier to compare it with its Broxton
counterpart.

This also flips the order of Misc IO and power well 1 disabling which
matches the enabling order. The specification doesn't prescribe the
disabling order, so this should be fine.

v2:
- Fix incorrect enable vs. disable power well call in
  skl_display_core_uninit() (Patrik)
- Add commit comment about chaning the order of PW1 and Misc IO power
  well disabling (Patrik)

CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459773777-10701-1-git-send-email-imre.deak@intel.com

On SKL/KBL suspend-to-idle (aka freeze/s0ix) is performed with DMC
firmware assistance where the target display power state is DC6. On
Broxton on the other hand we don't use the firmware for this, but rely
instead on a manual DC9 flow. For this we have to uninitialize the
display following the BSpec display uninit sequence, just as during
S3/S4, so make sure we follow this sequence.

CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-8-git-send-email-imre.deak@intel.com

The display power well support and DC state management doesn't depend on
runtime PM support, so remove the incorrect asserts about this.

Also Broxton does support DC5, so the related assert in
assert_can_enable_dc5() is incorrect. There is a more generic and
correct assert for this already in gen9_set_dc_state(), so we can remove
all the other ones.

At the same time convert WARNs to WARN_ONCE for consistency with the
other DC state asserts.

CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-7-git-send-email-imre.deak@intel.com

So far we only power well enabling was synchronous not disabling. Since
we don't exactly know how the firmware (both DMC and PCU) synchronizes
against the actual power well state during DC transitions, make the
disabling also synchronous.

CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-6-git-send-email-imre.deak@intel.com

DMC forces on power well 1 and the misc IO power well by setting the
corresponding request bits both in the BIOS and the DEBUG power well
request registers. This is somewhat unexpected since the firmware should
really just save and restore state but not alter it. We also depend on
being able to disable power well 1, and the misc IO power well before
entering S3/S4 on BXT and SKL or entering DC9 on BXT. To fix this make
sure these request bits are cleared whenever we want to disable the
given power wells.

On SKL there is another twist where the firmware also clears the power
well 1 request bit in HSW_POWER_WELL_DRIVER (but not that of the misc IO
power well). This happens to not cause a problem due to the forced-on
request bits in the other request registers.

I've filed a bug about all this, but fixing that may take a while and
having this sanity check in place makes sense even for future firmware
versions.

At the same time also check the KVMR request bits. I haven't seen this
being altered, but we don't expect any request bits in here either, so
sanitize this register as well.

v2:
- Apply the workaround on SKL as well. I noticed the related failure
  from the CI report, later Patrik also reported seeing it on his
  machine.

CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459851965-6137-1-git-send-email-imre.deak@intel.com

This register is read-only, so we have never actually set
OCL2_LDOFUSE_PWR_DIS in it as specified by the specification. Add a code
comment about this. I filed a specification update request to clarify
this there.

CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-4-git-send-email-imre.deak@intel.com

This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.

v2:
- Remove the FIXME comment, we left in the code exactly about this
  issue. (Ville)

CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-3-git-send-email-imre.deak@intel.com

DMC version 1.06 has a known bug, where the firmware polls forever for a
port PLL to lock, if the PLL was disabled when entering DC5, which locks
up the machine. Version 1.07 fixes this, so make that the minimum
required version on BXT.

CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-2-git-send-email-imre.deak@intel.com