The mx3_gpio_irq_handler() is also called on imx6q which has GIC as
the primary interrupt controller.  As GIC implements the fasteoi flow
control, we need to add chained_irq_enter/exit() to
mx3_gpio_irq_handler() for signaling EOI, otherwise system will hang
whenever there is a gpio irq triggered.

v2: use chained_irq_{enter,exit}()
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Currently the Nomadik GPIO driver tracks enabled/disabled interrupt
status with a local variable, switch to using the interrupt core.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Remove duplicate "return" statement
  drm/nv04/crtc: Bail out if FB is not bound to crtc
  drm/nouveau: fix nv04_sgdma_bind on non-"4kB pages" archs
  drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate
  drm/nouveau: fix oops on pre-semaphore hardware
  drm/nv50/crtc: Bail out if FB is not bound to crtc
  drm/radeon/kms: fix DP detect and EDID fetch for DP bridges

* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
  ARM: CSR: add missing sentinels to of_device_id tables
  ARM: cns3xxx: Fix newly introduced warnings in the PCIe code
  ARM: cns3xxx: Fix compile error caused by hardware.h removed
  ARM: davinci: fix cache flush build error
  ARM: davinci: correct MDSTAT_STATE_MASK
  ARM: davinci: da850 EVM: read mac address from SPI flash
  OMAP: omap_device: fix !CONFIG_SUSPEND case in _noirq handlers
  OMAP2430: hwmod: musb: add missing terminator to omap2430_usbhsotg_addrs[]
  OMAP3: clock: indicate that gpt12_fck and wdt1_fck are in the WKUP clockdomain
  OMAP4: clock: fix compile warning
  OMAP4: clock: re-enable previous clockdomain enable/disable sequence
  OMAP: clockdomain: Wait for powerdomain to be ON when using clockdomain force wakeup
  OMAP: powerdomains: Make all powerdomain target states as ON at init

The LTTng 2.0 kernel tracer (stand-alone module package, available at
http://lttng.org) uses the 0xF6 ioctl range for tracer control and
transport operations.
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://github.com/chrismason/linux:
  Btrfs: add dummy extent if dst offset excceeds file end in
  Btrfs: calc file extent num_bytes correctly in file clone
  btrfs: xattr: fix attribute removal
  Btrfs: fix wrong nbytes information of the inode
  Btrfs: fix the file extent gap when doing direct IO
  Btrfs: fix unclosed transaction handle in btrfs_cont_expand
  Btrfs: fix misuse of trans block rsv
  Btrfs: reset to appropriate block rsv after orphan operations
  Btrfs: skip locking if searching the commit root in csum lookup
  btrfs: fix warning in iput for bad-inode
  Btrfs: fix an oops when deleting snapshots

kmemleak is reporting that 32 bytes are being leaked by FUSE:

  unreferenced object 0xe373b270 (size 32):
  comm "fusermount", pid 1207, jiffies 4294707026 (age 2675.187s)
  hex dump (first 32 bytes):
    01 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<b05517d7>] kmemleak_alloc+0x27/0x50
    [<b0196435>] kmem_cache_alloc+0xc5/0x180
    [<b02455be>] fuse_alloc_forget+0x1e/0x20
    [<b0245670>] fuse_alloc_inode+0xb0/0xd0
    [<b01b1a8c>] alloc_inode+0x1c/0x80
    [<b01b290f>] iget5_locked+0x8f/0x1a0
    [<b0246022>] fuse_iget+0x72/0x1a0
    [<b02461da>] fuse_get_root_inode+0x8a/0x90
    [<b02465cf>] fuse_fill_super+0x3ef/0x590
    [<b019e56f>] mount_nodev+0x3f/0x90
    [<b0244e95>] fuse_mount+0x15/0x20
    [<b019d1bc>] mount_fs+0x1c/0xc0
    [<b01b5811>] vfs_kern_mount+0x41/0x90
    [<b01b5af9>] do_kern_mount+0x39/0xd0
    [<b01b7585>] do_mount+0x2e5/0x660
    [<b01b7966>] sys_mount+0x66/0xa0

This leak report is consistent and happens once per boot on
3.1.0-rc5-dirty.

This happens if a FORGET request is queued after the fuse device was
released.
Reported-by: NSitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Tested-by: NSitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 37fb3a30 ("fuse: fix flock") added in 3.1-rc4 caused flock() to
fail with ENOSYS with the kernel ABI version 7.16 or earlier.

Fix by falling back to testing FUSE_POSIX_LOCKS for ABI versions 7.16
and earlier.
Reported-by: NMartin Ziegler <ziegler@email.mathematik.uni-freiburg.de>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Tested-by: NMartin Ziegler <ziegler@email.mathematik.uni-freiburg.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'v4l_for_linus' of git://linuxtv.org/mchehab/for_linus:
  [media] vp7045: fix buffer setup
  [media] nuvoton-cir: simplify raw IR sample handling
  [media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
  [media] v4l2: Fix documentation of the codec device controls
  [media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240
  [media] gspca - sonixj: Fix wrong register mask for sensor om6802
  [media] gspca - ov519: Fix LED inversion of some ov519 webcams
  [media] pwc: precedence bug in pwc_init_controls()

* 'for-linus' of git://openrisc.net/~jonas/linux:
  Add missing DMA ops
  openrisc: don't use pt_regs in struct sigcontext

You can see there's no file extent with range [0, 4096]. Check this by
btrfsck:

 # btrfsck /dev/sda7
 root 5 inode 258 errors 100
 ...
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

num_bytes should be 4096 not 12288.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

An attribute is not removed by 'setfattr -x attr file' and remains
visible in attr list. This makes xfstests/062 pass again.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

If we write some data into the data hole of the file(no preallocation for this
hole), Btrfs will allocate some disk space, and update nbytes of the inode, but
the other element--disk_i_size needn't be updated. At this condition, we must
update inode metadata though disk_i_size is not changed(btrfs_ordered_update_i_size()
return 1).

 # mkfs.btrfs /dev/sdb1
 # mount /dev/sdb1 /mnt
 # touch /mnt/a
 # truncate -s 856002 /mnt/a
 # dd if=/dev/zero of=/mnt/a bs=4K count=1 conv=nocreat,notrunc
 # umount /mnt
 # btrfsck /dev/sdb1
 root 5 inode 257 errors 400
 found 32768 bytes used err is 1
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

When we write some data to the place that is beyond the end of the file
in direct I/O mode, a data hole will be created. And Btrfs should insert
a file extent item that point to this hole into the fs tree. But unfortunately
Btrfs forgets doing it.

The following is a simple way to reproduce it:
 # mkfs.btrfs /dev/sdc2
 # mount /dev/sdc2 /test4
 # touch /test4/a
 # dd if=/dev/zero of=/test4/a seek=8 count=1 bs=4K oflag=direct conv=nocreat,notrunc
 # umount /test4
 # btrfsck /dev/sdc2
 root 5 inode 257 errors 100
Reported-by: NTsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Tested-by: NTsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

The function - btrfs_cont_expand() forgot to close the transaction handle before
it jump out the while loop. Fix it.
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

At the beginning of create_pending_snapshot, trans->block_rsv is set
to pending->block_rsv and is used for snapshot things, however, when
it is done, we do not recover it as will.
Signed-off-by: NLiu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

While truncating free space cache, we forget to change trans->block_rsv
back to the original one, but leave it with the orphan_block_rsv, and
then with option inode_cache enable, it leads to countless warnings of
btrfs_alloc_free_block and btrfs_orphan_commit_root:

WARNING: at fs/btrfs/extent-tree.c:5711 btrfs_alloc_free_block+0x180/0x350 [btrfs]()
...
WARNING: at fs/btrfs/inode.c:2193 btrfs_orphan_commit_root+0xb0/0xc0 [btrfs]()
Signed-off-by: NLiu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

It's not enough to just search the commit root, since we could be cow'ing the
very block we need to search through, which would mean that its locked and we'll
still deadlock.  So use path->skip_locking as well.  Thanks,
Signed-off-by: NJosef Bacik <josef@redhat.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

iput() shouldn't be called for inodes in I_NEW state.
We need to mark inode as constructed first.

WARNING: at fs/inode.c:1309 iput+0x20b/0x210()
Call Trace:
 [<ffffffff8103e7ba>] warn_slowpath_common+0x7a/0xb0
 [<ffffffff8103e805>] warn_slowpath_null+0x15/0x20
 [<ffffffff810eaf0b>] iput+0x20b/0x210
 [<ffffffff811b96fb>] btrfs_iget+0x1eb/0x4a0
 [<ffffffff811c3ad6>] btrfs_run_defrag_inodes+0x136/0x210
 [<ffffffff811ad55f>] cleaner_kthread+0x17f/0x1a0
 [<ffffffff81035b7d>] ? sub_preempt_count+0x9d/0xd0
 [<ffffffff811ad3e0>] ? transaction_kthread+0x280/0x280
 [<ffffffff8105af86>] kthread+0x96/0xa0
 [<ffffffff814336d4>] kernel_thread_helper+0x4/0x10
 [<ffffffff8105aef0>] ? kthread_worker_fn+0x190/0x190
 [<ffffffff814336d0>] ? gs_change+0xb/0xb
Signed-off-by: NSergei Trofimovich <slyfox@gentoo.org>
CC: Konstantin Khlebnikov <khlebnikov@openvz.org>
Tested-by: NDavid Sterba <dsterba@suse.cz>
CC: Josef Bacik <josef@redhat.com>
CC: Chris Mason <chris.mason@oracle.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

We can reproduce this oops via the following steps:

$ mkfs.btrfs /dev/sdb7
$ mount /dev/sdb7 /mnt/btrfs
$ for ((i=0; i<3; i++)); do btrfs sub snap /mnt/btrfs /mnt/btrfs/s_$i; done
$ rm -fr /mnt/btrfs/*
$ rm -fr /mnt/btrfs/*

then we'll get
------------[ cut here ]------------
kernel BUG at fs/btrfs/inode.c:2264!
[...]
Call Trace:
 [<ffffffffa05578c7>] btrfs_rmdir+0xf7/0x1b0 [btrfs]
 [<ffffffff81150b95>] vfs_rmdir+0xa5/0xf0
 [<ffffffff81153cc3>] do_rmdir+0x123/0x140
 [<ffffffff81145ac7>] ? fput+0x197/0x260
 [<ffffffff810aecff>] ? audit_syscall_entry+0x1bf/0x1f0
 [<ffffffff81153d0d>] sys_unlinkat+0x2d/0x40
 [<ffffffff8147896b>] system_call_fastpath+0x16/0x1b
RIP  [<ffffffffa054f7b9>] btrfs_orphan_add+0x179/0x1a0 [btrfs]

When it comes to btrfs_lookup_dentry, we may set a snapshot's inode->i_ino
to BTRFS_EMPTY_SUBVOL_DIR_OBJECTID instead of BTRFS_FIRST_FREE_OBJECTID,
while the snapshot's location.objectid remains unchanged.

However, btrfs_ino() does not take this into account, and returns a wrong ino,
and causes the oops.
Signed-off-by: NLiu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

dvb_usb_device_init calls the frontend_attach method of this driver which
uses vp7045_usb_ob. In order to have a buffer ready in vp7045_usb_op, it has to
be allocated before that happens.

Luckily we can use the whole private data as the buffer as it gets separately
allocated on the heap via kzalloc in dvb_usb_device_init and is thus apt for
use via usb_control_msg.

This fixes a
	BUG: unable to handle kernel paging request at 0000000000001e78

reported by Tino Keitel and diagnosed by Dan Carpenter.

Cc: stable@kernel.org # For v3.0 and upper
Tested-by: NTino Keitel <tino.keitel@tikei.de>
Signed-off-by: NFlorian Mickler <florian@mickler.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.
Reported-by: NStephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: stable@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In the unlikely case that pci_find_bus() should return NULL
viacam_serial_is_enabled() is going to dereference a NULL pointer and
blow up. Better safe than sorry, so be defensive and check the
pointer.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixed missing ids of the codec controls description in the controls.xml file.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The images are clearer with a lower bridge clock.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The bug was introduced by git commit 0e4d413a, giving very dark images.
Signed-off-by: NLuiz Carlos Ramos <lramos.prof@yahoo.com.br>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The list of the webcams which have LED inversion was rebuild scanning
ms-win .inf files.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

'!' has higher precedence than '&' so we need parenthesis here.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For the initial architecture submission, not all of the DMA ops were
implemented.  This patch adds the *map_page and *map_sg variants of the
DMA mapping ops.

This patch is currently of interest mainly to some drivers that haven't
been submitted upstream yet.
Signed-off-by: NJonas Bonn <jonas@southpole.se>

The of_device_id tables used for matching should be terminated with
empty sentinel values.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NBarry Song <baohua.song@csr.com>

When CONFIG_NET is disabled, SCSI_QLA_ISCSI selects SCSI_ISCSI_ATTRS,
which uses network interfaces, so the build fails with multiple errors:

  warning: (ISCSI_TCP && SCSI_CXGB3_ISCSI && SCSI_CXGB4_ISCSI && SCSI_QLA_ISCSI && INFINIBAND_ISER) selects SCSI_ISCSI_ATTRS which has unmet direct dependencies (SCSI && NET)

  ERROR: "skb_trim" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
  ERROR: "netlink_kernel_create" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
  ERROR: "netlink_kernel_release" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
  ...

so make SCSI_QLA_ISCSI also depend on NET to prevent the build errors.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc:	Ravi Anand <ravi.anand@qlogic.com>
Cc:	Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc:	iscsi-driver@qlogic.com
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  ARM: 7088/1: entry: fix wrong parameter name used in do_thumb_abort
  ARM: 7080/1: l2x0: make sure I&D are not locked down on init
  ARM: 7081/1: mach-integrator: fix the clocksource
  NET: am79c961: fix race in link status code
  ARM: 7067/1: mm: keep significant bits in pfn_valid

Commit be020f86, "ARM: entry: abort-macro: specify registers to be
used for macros", while replacing register numbers with macro parameter
names, mismatched the name used for r1. For me, this resulted in user
space built for EABI with -march=armv4t -mtune=arm920t -mthumb-interwork
-mthumb broken on my OMAP1510 based Amstrad Delta (old ABI and no thumb
still worked for me though).

Fix this by using correct parameter name fsr instead of mismatched psr,
used by callers for another purpose.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since backlight_types[] isn't modified, let's declare it const.  That
was probably the intention of the author of commit bb7ca747
("backlight: add backlight type"), via which the "const char const *"
construct was introduced.  The duplicate const was detected by sparse.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>