Fix bug which occurs when more than <limit> packets are available during
napi-poll, leading to "delays" and retransmissions on the network.

Check for (count < limit) before checking the get_rx_status in tse_rx-function.
Function get_rx_status is reading from the response-fifo.
If there is currently a response in the fifo,
reading the last byte of the response pops the value from the fifo.
If the limit is checked as second condition
and the limit is reached the fifo is popped but the packet is not processed.
Signed-off-by: NAndreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incorrect NAPI polling caused WARNING at net/core/dev.c net_rx_action.
Some stability issues were also seen at high throughput and system
load before this patch.

This patch contains several changes in altera_tse_main.c:

- tse_rx() is fixed to not process more than `limit` frames

- tse_poll() is refactored to match NAPI logic
  - only received frames are counted for return value
  - removed bogus condition `(rxcomplete >= budget || txcomplete > 0)`
  - replace by: if (rxcomplete < budget) -> call __napi_complete and enable irq

- altera_isr()
  - replace spin_lock_irqsave() by spin_lock() - we are in isr
  - use spinlocks just over irq manipulation, not over __napi_schedule
  - reset IRQ first, then disable and schedule napi

This is a cleaned up resubmission from Vlastimil's recent submission.
Signed-off-by: NVlastimil Setka <setka@vsis.cz>
Signed-off-by: NRoman Pisl <rpisl@kky.zcu.cz>
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects a typo in the way tx_fifo_depth is read from the
devicetree. This patch was submitted by Vlastimil about a week ago,
and is now cleaned up and resubmitted.
Signed-off-by: NVlastimil Setka <setka@vsis.cz>
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This debug output is not really an error message since mac reset can fail
if the phy clocks are gated, specifically when the phy has been placed in
a powered down or isolation mode. The netdev output masks were changed from
err to dbg, and comments added in the code.
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change use of Altera TSE's MDIO access from phy 0 registers to phy 1
registers. This allows support for GMII, MII, RGMII, and SGMII
designs where the external PHY is always accesible through
Altera TSE's MDIO phy 1 registers and Altera's PCS is accessible
through MDIO phy 0 registers for SGMII applications.
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Tested-by: NKai Lin Ng <kailng@altera.com>
Tested-by: NDalon Westergreen <dwesterg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Altera network device doesn't come up after

ifconfig eth0 down
ifconfig eth0 up

The reason behind is clearing priv->phydev during tse_shutdown().
The phydev is not restored back at tse_open().

Resubmiting as to follow Tobias Klauser suggestion.
phy_start/phy_stop are called on each ifup/ifdown and
phy_disconnect is called once during the module removal.
Signed-off-by: NKostya Belezko <bkostya@hotmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch avoids PHY and MDIO probing if no PHY chip is present.
This is the case mainly in optical links where there is no need for
PHY chip, and therefore no need of MDIO. In this scenario Ethernet
MAC is directly connected to an optical module through an external
SFP transceiver.
Signed-off-by: NWalter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move PHY get addr and MDIO create to a new function to improve readability
and make it easier to avoid its usage. This will be useful for example in
the case where there is no PHY chip.
Signed-off-by: NWalter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to call ether_setup after alloc_ethdev since it was
already called there.

Follow commits c706471b ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbf ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch disables multicast hash filtering if present in the hardware
and uses promiscuous mode instead until the problem with multicast
filtering has been debugged, integrated and tested.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the many sparse errors and warnings contained in the
initial submission of the Altera Triple Speed Ethernet driver, and a
few minor cppcheck warnings. Changes are tested on ARM and NIOS2
example designs, and compile tested against multiple architectures.
Typical issues addressed were as follows:

altera_tse_ethtool.c:136:19: warning: incorrect type in argument
    1 (different address spaces)
altera_tse_ethtool.c:136:19:    expected void const volatile
    [noderef] <asn:2>*addr
altera_tse_ethtool.c:136:19:    got unsigned int *<noident>
...
altera_sgdma.c:129:31: warning: cast removes address space of
    expression
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses a fault in the error recovery path of the probe
routine where the netdev structure was not being unregistered properly
leading to a panic only when the phy probe failed.

Abbreviated panic stack seen is as follows:

(free_netdev+0xXX) from (altera_tse_probe+0xXX)
(altera_tse_probe+0xXX) from (platform_drv_probe+0xXX)
(platform_drv_probe+0xXX) from (driver_probe_device+0xXX)
(driver_probe_device+0xXX) from (__driver_attach+0xXX)
(__driver_attach+0xXX) from (bus_for_each_dev+0xXX)
(bus_for_each_dev+0xXX) from (driver_attach+0xXX)
(driver_attach+0xXX) from (bus_add_driver+0xXX)
(bus_add_driver+0xXX) from (driver_register+0xXX)
(driver_register+0xXX) from (__platform_driver_register+0xXX)
(__platform_driver_register+0xXX) from (altera_tse_driver_init+0xXX)
(altera_tse_driver_init+0xXX) from (do_one_initcall+0xXX)
(do_one_initcall+0xXX) from (kernel_init_freeable+0xXX)
(kernel_init_freeable+0xXX) from (kernel_init+0xXX)
(kernel_init+0xXX) from (ret_from_fork+0xXX)
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch initializes the pause quanta set for transmitted pause frames
to the IEEE specified default of 0xffff.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch works around a recently discovered unaligned receive dma problem
with the Altera SGMDA. The Altera SGDMA component cannot be configured to
DMA data to unaligned addresses for receive packet operations from the
Triple Speed Ethernet component because of a potential data transfer
corruption that can occur. This patch addresses this issue by
utilizing the shift 16 bits feature of the Altera Triple Speed Ethernet
component and modifying the receive buffer physical addresses accordingly
such that the target receive DMA address is always aligned on a 32-bit
boundary.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Tested-by: NMatthew Gerlach <mgerlach@altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.

Done via coccinelle script:

$ cat typecast_2.cocci
@@
type T;
T *foo;
@@

-	(T *)foo
+	foo
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the main driver and header file for the Altera Triple
Speed Ethernet driver.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>