This stubs in clk_get_sys() from the ARM clkdev implementation.
Tentatively conver the clk_get() lookup code to use this, and once the
rest of the in-tree users are happy with this, it can replace the
fallback lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The only user for this is the SH-Mobile r_clk, which is now added as a
root clock and can be kicked via propagate_rate() as usual. Given that,
there is no longer any need for the special clk_recalc_rate(), so we kill
it off.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This causes the generic clk_set_parent() implementation to be a bit more
intelligent. A clk_reparent() is added to move the clock over to the new
parent's sibling list, which then allows the generic rate propagation
code to succeed. This also becomes a nop if the new and old parents are
unchanged.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There are a couple of instances where a clk_enable() can fail, which the
SH-Mobile code presently handles, but doesn't get reported all the way
back up. This fixes up the return type so the errors make it all the way
down to the drivers.

Additionally, we now also error out properly if the parent enable fails.
Prep work for aggressively turning off unused clocks on boot.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Kill off all of the clk_always_enabled leftovers and use the new flag
directly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There is no real distinction here in behaviour, either a clock needs to
be enabled on initialiation or not. The ALWAYS_ENABLED flag was always
intended to only apply to clocks that were physically always on and could
simply not be disabled at all from software. Unfortunately over time this
was abused and the meaning became a bit blurry.

So, we kill off both of all of those paths now, as well as the newer
NEEDS_INIT flag, and consolidate on a CLK_ENABLE_ON_INIT. Clocks that
need to be enabled on initialization can set this, and it will purposely
enable them and bump the refcount up.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This resyncs the rate propagation strategy with the scheme used by the
OMAP clock framework. Child clocks are tracked on a list under each
parent and propagation happens there specifically rather than constantly
iterating over the global clock list.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds a followparent_recalc() helper for clocks that just follow the
parent's rate. Switch over the few CPUs that use this scheme for some of
their clocks.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is prep work for cleaning up some of the rate propagation bits.
Trivial conversion.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch updates the clock framework use count code.
With this patch the enable() and disable() callbacks
only get called when counting from and to zero.
While at it the kref stuff gets replaced with an int.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This follows the sparc changes a439fe51.

Most of the moving about was done with Sam's directions at:

http://marc.info/?l=linux-sh&m=121724823706062&w=2

with subsequent hacking and fixups entirely my fault.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SuperH specific funcion clk_always_enable(), useful to enable MSTPCR
bits in processor or board specific code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add arch_flags to struct clk so we can keep per-clock private data
somewhere and share code between multiple clocks.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch contains the following cleanups:
- make the following needlessly global code static:
  - cf-enabler.c: cf_init()
  - cpu/clock.c: __clk_enable()
  - cpu/clock.c: __clk_disable()
  - process_32.c: default_idle()
  - time_32.c: struct clocksource_sh
  - timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
  - process_{32,64}.c: disable_hlt()
  - process_{32,64}.c: enable_hlt()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is an optional component of the clock framework. However,
as we're going to be using this in the cpufreq drivers, add
support for it to the framework.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously this was done in cpuinfo, but with the number of clocks
growing, it makes more sense to place this in a different proc entry.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for the SH7722 (MobileR) to the clock framework.
Signed-off-by: Ndmitry pervushin <dimka@nomadgs.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds a relatively simplistic clock framework for sh.  The initial goal
behind this is to clean up the arch/sh/kernel/time.c mess and to get the CPU
subtype-specific frequency setting and calculation code moved somewhere more
sensible.

This only deals with the core clocks at the moment, though it's trivial for
other drivers to define their own clocks as desired.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>