to allow easy addition of IGEP3
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

IGEP2 and IGEP3 boards are very similar and can be merged into one file.
Start refactoring with changing igep2 to igep where applicable.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Most boards use exactly the same configuration for musb initialization.
Create a default that can be shared amount different boards.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

and reduce amount of copy/paste
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
CC: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add common-board-devices.c that will contain the code for peripheral
devices initializatoin shared between multiple boards.
Start small with touchscreen initialization.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

cat of debugfs entry for vp_volt provides voltage. The additional pr_notice
is just spam on console and provides no additional information.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

pm44xx.c is built only when CONFIG_PM is setup,
remove redundant CONFIG_PM check.

This also fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=25022Reported-by: NMartin Etti <ettl.martin@gmx.de>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Delete created debugfs entries if probe fails.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

If the probe fails, the node should be deleted from sr_list.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Add missing iounmap() to error paths.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

We are releasing the memory region, but never actually request it.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

sr_late_init() will take care of freeing the resources.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Removing extra lines, spaces and unneeded parenthesis.
Collapsing an if statement to detect the type of error.

l3_smx:
- Fixing the message printed on error.

So now: 				looks like:
"No Error Error seen..."		"No Error seen..."
"In-Band Error Error seen..."	"In-Band Error seen..."

Other messages are self explanatory, no "Error" added to them.
(E.g.: "Address Hole seen...")
Signed-off-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

l3_smx:
- Add missing free_irq and remove an empty goto label.

l3_noc:
- If kzalloc fails driver shouldn't continue with a NULL pointer.
- Add missing free_irq and remove empty goto labels.
- Safe to assume that if we reached the end point of execution
  without errors, then return value is 0, so replacing instead
  another goto.
Signed-off-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

replace "printk(KERN_ERR" by "pr_err("
and fix needlessly multi-lined #ifdef
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Convert boards that use SMSC911x to use gpmc-smsc911x.
Also allocate struct platform_device dynamically.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: folded in a fix from Igor Grindberg]
Signed-off-by: NTony Lindgren <tony@atomide.com>

SMSC911x devices attached to OMAP GPMC always use low level irqs.
Setting the appropriate flag in the irq resourse strucure allows using
.flags field in the omap_smsc911x_platform_data for driver specific
flags
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Use irq_set_chip_and_handler() instead. Converted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Convert to the new function names. Automated with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied
from Phoenix TWL6030.
Add CLK32KG platform data to blaze and omap4panda board file.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Make sure the kernel can be compiled with both OMAP2 and OMAP3 camera
support linked in, and give public symbols proper omap2/omap3 prefixes.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The omap3isp platform device requires platform data. Instead of
registering the device in omap2_init_devices(), export an
omap3_init_camera() function to fill the device structure with the
platform data pointer and register the device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The ISP CBUFF module isn't use, its resource isn't needed.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add new/changed base address definitions and resources for
OMAP3630 ISP.

The OMAP3430 CSI2PHY block is same as the OMAP3630 CSIPHY2
block. But the later name is chosen as it gives more symmetry
to the names.
Signed-off-by: NTuukka Toivonen <tuukkat76@gmail.com>
Signed-off-by: NVimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit db97eb7d
(omap: gpmc: enable irq mode in gpmc) enabled interrupts for
GPMC (General Purpose Memory Controller). However, looks like
this patch only works on omap3. Fix the issues to avoid warnings
on omap4 during the boot.

GPMC: number of chip select is 8, CS0 to CS7. One less IRQ
allocated throws below warning at boot:

[    0.429290] Trying to install type control for IRQ409
[    0.429290] Trying to set irq flags for IRQ409

Resolve following warning messages in boot when irq chip is not set:

[    0.429229] Trying to install interrupt handler for IRQ402
[    0.429229] Trying to install interrupt handler for IRQ403
[    0.429229] Trying to install interrupt handler for IRQ404
[    0.429260] Trying to install interrupt handler for IRQ405
[    0.429260] Trying to install interrupt handler for IRQ406
[    0.429260] Trying to install interrupt handler for IRQ407
[    0.429290] Trying to install interrupt handler for IRQ408

Resolve following warning in OMAP4:
[    0.429290] gpmc: irq-20 could not claim: err -22
Signed-off-by: NBalaji T K <balajitk@ti.com>
[tony@atomide.com: combined patches into one, updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

the pandaboard does not use the VUSIM or VAUX1 power regulators on the TWL6030
and are left floating. if the VUSIM and VAUX1 power regulators are initilized,
noise on the unloaded regulators generates an overcurrent interrupt causing the
system to power down. this patch removes the initialization of the unused power
regulators of VUSIM and VAUX1.
Signed-off-by: NDavid Anders <x0132446@ti.com>
Acked-by: NAndy Green <andy.green@linaro.org>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The handler function may be called from the point it is registered.
Since the handler inspects IRQ numbers, we must set them up before
registration.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix the return value for the successful case.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding DVI support to OMAP4 PandaBoard.

PandaBoard uses TFP410 DVI Framer chip
http://focus.ti.com/lit/ds/symlink/tfp410.pdf

The TFP410 gets its power enable and display data over GPIO lines muxed
in from OMAP4430. PandaBoard supports other LCD displays through
expansion
connectors, following board rework. This will disable the DVI interface.
However, the existing mux settings remain the same

PandaBoard additionally supports display over HDMI interface. It is
mutually exclusive to display over DVI. Hence the mux settings need to
be
configured seperately, as and when HDMI is enabled

Also, I2C3 bus used for reading EDID data from DVI Monitors is
registered here. Since the design is similar to BeagleBoard, the code
for the same is taken from the kernel.org commit e3333f48
(omap: Adding beagle i2c eeprom driver to read EDID)
Reviewed-by: NManjunath G Kondaiah <manjugk@ti.com>
Reviewed-by: NAnand Gadiyar <gadiyar@ti.com>
Reviewed-by: NNishanth Menon <nm@ti.com>
Reviewed-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NRaghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: fixed conflicts with HDMI]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Adding  board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Adding  board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The wl1271's irq line is completely controlled by the 1271 device, and
the host does not not need to pull it up.

While there's no functional effect, letting the host pull this line up is
just redundant, and wastes power.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adapts the register offsets used to read the CPU DIE ID registers
when run on 44XX so they match what is in the OMAP4430 Reference Manual
page 269
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove duplicate mux modes to make the binary smaller:

text    data     bss     dec     hex filename
9378   24472       0   33850    843a mux44xx.o
9378   19104       0   28482    6f42 mux44xx.o

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix compile when CONFIG_OMAP_MUX is not selected
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use the mux framework to initialise the serial pads.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use the mux framework to initialise the serial pads.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>