Delay_probes are new packets in the DRBD protocol, which allow
DRBD to know the current delay packets have on the data socket.
(relative to the meta data socket)
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The "surplus" bits of the old (smaller) bitmap must be clean
in case of online-grow without resync.

Note: Reverted 67ae8b80d4a116ab3b7094eb3723506b20c06dff as
well, since the lines added by this patch are redundant. The
bits get set by the bm_set_surplus(b) call before that.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Some wish to be notified of all instances of split brain, not just those that
go unresolved.  The initial-split-brain handler is called to notify someone
upon  detection of all split brain conditions even if auto-recovery policies
are configured.
Signed-off-by: NAdam Gandelman <adam.gandelman@linbit.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The condition does not fit the commend (I may well be Primary,
even if I lost the disk earlier and now the connection).

And this is catched below anyways, where it also gets logged.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Even if it should never happen if the peer does behave, we need to
double check, and not even attempt access beyond end of device.
It usually would be caught by lower layers, resulting in "IO error",
but may also end up in the internal meta data area.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In case both nodes are "inconsistent", invalidate would
have started a resync anyways, without a chance to ever
succeed, just filling the logs with warning messages.

Simply disallow that state change,
re-using the SS_NO_UP_TO_DATE_DISK return value.

This also changes the corresponding error string to
"Need access to UpToDate Data" -- I found the
"Refusing to be Primary without at least one UpToDate disk"
answer misleading in some situations anyways.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Don't forget to drain the digest in case we cannot satisfy a
checksum based resync or online-verify request.

It would additionally cause a protocoll error,
dropping the connection.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

block_id may be ID_SYNCER,
as well as checksum based resync request magic, or online verify magic.

Let's just drop that ASSERT.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

commit e4f925e1
Author: Philipp Reisner <philipp.reisner@linbit.com>
Date:   Wed Mar 17 14:18:41 2010 +0100

    drbd: Do not upgrade state to Outdated if already Inconsistent

prevented the necessary state transition for attaching while connected
(Diskless -> Consistent respectively Outdated).
This is the fix for the fix.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

There was a race condition:
  In a situation with a SyncSource+Primary and a SyncTarget+Secondary node,
  and a resync dependency to some other device. After both nodes decided
  to do the resync, the other device finishes its resync process.
  At that time SyncSource already sent the P_SYNC_UUID packet, and
  already updated its peer disk state to Inconsistent.
  The SyncTarget node waits for the P_SYNC_UUID and sends a state packet
  to report the resync dependency change. That packet still carries
  a disk state of Outdated.

Impact:
  If application writes come in, during that time on the Primary node,
  those do not get replicated, and the out-of-sync counter gets increased.
  => The completion of resync is not detected on the primary node.
  => stalled.
  Those blocks get resync'ed with the next resync, since the are get
  marked as out-of-sync in the bitmap.

In order to fix this, we filter out that wrong state change in the
sanitize_state() function.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

To document that we know about deprecation of proc_create,
even though we are not affected, as we don't use the ->data member,
open code proc_create_data(..., NULL);
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Filesystems with delalloc support may dirty inode during writepages.
As result inode will have dirty metadata flags even after write_inode.
In fact we have two dedicated functions for proper data and metadata
writeback. It is reasonable to separate flags updates in two stages.

https://bugzilla.kernel.org/show_bug.cgi?id=15906Signed-off-by: NDmitry Monakhov <dmonakhov@openvz.org>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

When umount calls sync_filesystem(), we first do a WB_SYNC_NONE
writeback to kick off writeback of pending dirty inodes, then follow
that up with a WB_SYNC_ALL to wait for it. Since umount already holds
the sb s_umount mutex, WB_SYNC_NONE ends up doing nothing and all
writeback happens as WB_SYNC_ALL. This can greatly slow down umount,
since WB_SYNC_ALL writeback is a data integrity operation and thus
a bigger hammer than simple WB_SYNC_NONE. For barrier aware file systems
it's a lot slower.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Prior to 2.6.32, setting /proc/sys/vm/dirty_writeback_centisecs disabled
periodic dirty writeback from kupdate. This got broken and now causes
excessive sys CPU usage if set to zero, as we'll keep beating on
schedule().

Cc: stable@kernel.org
Reported-by: NJustin Maggard <jmaggard10@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Make the PARIDE menu be displayed correctly, with proper/expected
indentation, by moving the GDROM kconfig symbol, which was
splitting the PARIDE kconfig symbol from its dependent symbols.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

blk_init_queue() allocates the request_queue structure and then
initializes it as needed (request_fn, elevator, etc).

Split initialization out to blk_init_allocated_queue_node.
Introduce blk_init_allocated_queue wrapper function to model existing
blk_init_queue and blk_init_queue_node interfaces.

Export elv_register_queue to allow a newly added elevator to be
registered with sysfs.  Export elv_unregister_queue for symmetry.

These changes allow DM to initialize a device's request_queue with more
precision.  In particular, DM no longer unconditionally initializes a
full request_queue (elevator et al).  It only does so for a
request-based DM device.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

goto has its place, but lets cut back on some of the more
frivolous uses of it.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Conflicts:
	fs/block_dev.c
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

After merging the block tree, today's linux-next build (powerpc ppc64_defconfig)
failed like this:

fs/nilfs2/the_nilfs.c: In function 'nilfs_discard_segments':
fs/nilfs2/the_nilfs.c:673: error: 'DISCARD_FL_BARRIER' undeclared (first use in this function)

Caused by commit fbd9b09a ("blkdev:
generalize flags for blkdev_issue_fn functions") interacting with commit
e902ec99 ("nilfs2: issue discard request
after cleaning segments") (which netered Linus' tree on about March 4 -
before v2.6.34-rc1).
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Just cast the page size to sector_t, that will always fit.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86/PCI: compute Address Space length rather than using _LEN
  x86/PCI: never allocate PCI MMIO resources below BIOS_END

If dentry found stale happens to be a root of disconnected tree, we
can't d_drop() it; its d_hash is actually part of s_anon and d_drop()
would simply hide it from shrink_dcache_for_umount(), leading to
all sorts of fun, including busy inodes on umount and oopsen after
that.

Bug had been there since at least 2006 (commit c636eb already has it),
so it's definitely -stable fodder.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: fix enabling regulator issue on max8925

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
  sfc: Change falcon_probe_board() to fail for unsupported boards
  sfc: Always close net device at the end of a disabling reset
  sfc: Wait at most 10ms for the MC to finish reading out MAC statistics
  sctp: Fix oops when sending queued ASCONF chunks
  sctp: fix to calc the INIT/INIT-ACK chunk length correctly is set
  sctp: per_cpu variables should be in bh_disabled section
  sctp: fix potential reference of a freed pointer
  sctp: avoid irq lock inversion while call sk->sk_data_ready()
  Revert "tcp: bind() fix when many ports are bound"
  net/usb: add sierra_net.c driver
  cdc_ether: fix autosuspend for mbm devices
  bluetooth: handle l2cap_create_connless_pdu() errors
  gianfar: Wait for both RX and TX to stop
  ipheth: potential null dereferences on error path
  smc91c92_cs: spin_unlock_irqrestore before calling smc_interrupt()
  drivers/usb/net/kaweth.c: add device "Allied Telesyn AT-USB10 USB Ethernet Adapter"
  bnx2: Update version to 2.0.9.
  bnx2: Prevent "scheduling while atomic" warning with cnic, bonding and vlan.
  bnx2: Fix lost MSI-X problem on 5709 NICs.
  cxgb3: Wait longer for control packets on initialization
  ...

The driver needs specific PHY and board support code for each SFC4000
board; there is no point trying to continue if it is missing.
Currently unsupported boards can trigger an 'oops'.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a regression introduced by commit
eb9f6744 "sfc: Implement ethtool
reset operation".
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original code would wait indefinitely if MAC stats DMA failed.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we finish processing ASCONF_ACK chunk, we try to send
the next queued ASCONF.  This action runs the sctp state
machine recursively and it's not prepared to do so.

kernel BUG at kernel/timer.c:790!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/module/ipv6/initstate
Modules linked in: sha256_generic sctp libcrc32c ipv6 dm_multipath
uinput 8139too i2c_piix4 8139cp mii i2c_core pcspkr virtio_net joydev
floppy virtio_blk virtio_pci [last unloaded: scsi_wait_scan]

Pid: 0, comm: swapper Not tainted 2.6.34-rc4 #15 /Bochs
EIP: 0060:[<c044a2ef>] EFLAGS: 00010286 CPU: 0
EIP is at add_timer+0xd/0x1b
EAX: cecbab14 EBX: 000000f0 ECX: c0957b1c EDX: 03595cf4
ESI: cecba800 EDI: cf276f00 EBP: c0957aa0 ESP: c0957aa0
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process swapper (pid: 0, ti=c0956000 task=c0988ba0 task.ti=c0956000)
Stack:
 c0957ae0 d1851214 c0ab62e4 c0ab5f26 0500ffff 00000004 00000005 00000004
<0> 00000000 d18694fd 00000004 1666b892 cecba800 cecba800 c0957b14
00000004
<0> c0957b94 d1851b11 ceda8b00 cecba800 cf276f00 00000001 c0957b14
000000d0
Call Trace:
 [<d1851214>] ? sctp_side_effects+0x607/0xdfc [sctp]
 [<d1851b11>] ? sctp_do_sm+0x108/0x159 [sctp]
 [<d1863386>] ? sctp_pname+0x0/0x1d [sctp]
 [<d1861a56>] ? sctp_primitive_ASCONF+0x36/0x3b [sctp]
 [<d185657c>] ? sctp_process_asconf_ack+0x2a4/0x2d3 [sctp]
 [<d184e35c>] ? sctp_sf_do_asconf_ack+0x1dd/0x2b4 [sctp]
 [<d1851ac1>] ? sctp_do_sm+0xb8/0x159 [sctp]
 [<d1863334>] ? sctp_cname+0x0/0x52 [sctp]
 [<d1854377>] ? sctp_assoc_bh_rcv+0xac/0xe1 [sctp]
 [<d1858f0f>] ? sctp_inq_push+0x2d/0x30 [sctp]
 [<d186329d>] ? sctp_rcv+0x797/0x82e [sctp]
Tested-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NYuansong Qiao <ysqiao@research.ait.ie>
Signed-off-by: NShuaijun Zhang <szhang@research.ait.ie>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calculating the INIT/INIT-ACK chunk length, we should not
only account the length of parameters, but also the parameters
zero padding length, such as AUTH HMACS parameter and CHUNKS
parameter. Without the parameters zero padding length we may get
following oops.

skb_over_panic: text:ce2068d2 len:130 put:6 head:cac3fe00 data:cac3fe00 tail:0xcac3fe82 end:0xcac3fe80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:127!
invalid opcode: 0000 [#2] SMP
last sysfs file: /sys/module/aes_generic/initstate
Modules linked in: authenc ......

Pid: 4102, comm: sctp_darn Tainted: G      D    2.6.34-rc2 #6
EIP: 0060:[<c0607630>] EFLAGS: 00010282 CPU: 0
EIP is at skb_over_panic+0x37/0x3e
EAX: 00000078 EBX: c07c024b ECX: c07c02b9 EDX: cb607b78
ESI: 00000000 EDI: cac3fe7a EBP: 00000002 ESP: cb607b74
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process sctp_darn (pid: 4102, ti=cb607000 task=cabdc990 task.ti=cb607000)
Stack:
 c07c02b9 ce2068d2 00000082 00000006 cac3fe00 cac3fe00 cac3fe82 cac3fe80
<0> c07c024b cac3fe7c cac3fe7a c0608dec ca986e80 ce2068d2 00000006 0000007a
<0> cb8120ca ca986e80 cb812000 00000003 cb8120c4 ce208a25 cb8120ca cadd9400
Call Trace:
 [<ce2068d2>] ? sctp_addto_chunk+0x45/0x85 [sctp]
 [<c0608dec>] ? skb_put+0x2e/0x32
 [<ce2068d2>] ? sctp_addto_chunk+0x45/0x85 [sctp]
 [<ce208a25>] ? sctp_make_init+0x279/0x28c [sctp]
 [<c0686a92>] ? apic_timer_interrupt+0x2a/0x30
 [<ce1fdc0b>] ? sctp_sf_do_prm_asoc+0x2b/0x7b [sctp]
 [<ce202823>] ? sctp_do_sm+0xa0/0x14a [sctp]
 [<ce2133b9>] ? sctp_pname+0x0/0x14 [sctp]
 [<ce211d72>] ? sctp_primitive_ASSOCIATE+0x2b/0x31 [sctp]
 [<ce20f3cf>] ? sctp_sendmsg+0x7a0/0x9eb [sctp]
 [<c064eb1e>] ? inet_sendmsg+0x3b/0x43
 [<c04244b7>] ? task_tick_fair+0x2d/0xd9
 [<c06031e1>] ? sock_sendmsg+0xa7/0xc1
 [<c0416afe>] ? smp_apic_timer_interrupt+0x6b/0x75
 [<c0425123>] ? dequeue_task_fair+0x34/0x19b
 [<c0446abb>] ? sched_clock_local+0x17/0x11e
 [<c052ea87>] ? _copy_from_user+0x2b/0x10c
 [<c060ab3a>] ? verify_iovec+0x3c/0x6a
 [<c06035ca>] ? sys_sendmsg+0x186/0x1e2
 [<c042176b>] ? __wake_up_common+0x34/0x5b
 [<c04240c2>] ? __wake_up+0x2c/0x3b
 [<c057e35c>] ? tty_wakeup+0x43/0x47
 [<c04430f2>] ? remove_wait_queue+0x16/0x24
 [<c0580c94>] ? n_tty_read+0x5b8/0x65e
 [<c042be02>] ? default_wake_function+0x0/0x8
 [<c0604e0e>] ? sys_socketcall+0x17f/0x1cd
 [<c040264c>] ? sysenter_do_call+0x12/0x22
Code: 0f 45 de 53 ff b0 98 00 00 00 ff b0 94 ......
EIP: [<c0607630>] skb_over_panic+0x37/0x3e SS:ESP 0068:cb607b74

To reproduce:

# modprobe sctp
# echo 1 > /proc/sys/net/sctp/addip_enable
# echo 1 > /proc/sys/net/sctp/auth_enable
# sctp_test -H 3ffe:501:ffff:100:20c:29ff:fe4d:f37e -P 800 -l
# sctp_darn -H 3ffe:501:ffff:100:20c:29ff:fe4d:f37e -P 900 -h 192.168.0.21 -p 800 -I -s -t
sctp_darn ready to send...
3ffe:501:ffff:100:20c:29ff:fe4d:f37e:900-192.168.0.21:800 Interactive mode> bindx-add=192.168.0.21
3ffe:501:ffff:100:20c:29ff:fe4d:f37e:900-192.168.0.21:800 Interactive mode> bindx-add=192.168.1.21
3ffe:501:ffff:100:20c:29ff:fe4d:f37e:900-192.168.0.21:800 Interactive mode> snd=10

------------------------------------------------------------------
eth0 has addresses: 3ffe:501:ffff:100:20c:29ff:fe4d:f37e and 192.168.0.21
eth1 has addresses: 192.168.1.21
------------------------------------------------------------------
Reported-by: NGeorge Cheimonidis <gchimon@gmail.com>
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the change of the atomics to percpu variables, we now
have to disable BH in process context when touching percpu variables.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sctp attempts to update an assocition, it removes any
addresses that were not in the updated INITs.  However, the loop
may attempt to refrence a transport with address after removing it.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>