On some broken motherboards (at least one NForce3 based AMD64 laptop)
the PIT timer runs at a incorrect frequency.  This patch adds a new
option "apicpmtimer" that allows to use the APIC timer and calibrate it
using the PMTimer.  It requires the earlier patch that allows to run the
main timer from the APIC.

Specifying apicpmtimer implies apicmaintimer.

The option defaults to off for now.

I tested it on a few systems and the resulting APIC timer frequencies
were usually a bit off, but always <1%, which should be tolerable.

TBD figure out heuristic to enable this automatically on the affected
systems TBD perhaps do it on all NForce3s or using DMI?
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Another piece from the no-idle-tick patch.

This can be enabled with the "apicmaintimer" option.

This is mainly useful when the PIT/HPET interrupt is unreliable.
Note there are some systems that are known to stop the APIC
timer in C3. For those it will never work, but this case
should be automatically detected.

It also only works with PM timer right now. When HPET is used
the way the main timer handler computes the delay doesn't work.

It should be a bit more efficient because there is one less
regular interrupt to process on the boot processor.

Requires earlier bugfix from Venkatesh
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Most users don't need it so no need to waste memory.
This means an user has to specify the appropiate number of
hotplug CPUs on the command line with additional_cpus=...
or fix their BIOS to follow the convention in
Documentation/x86-64/cpu-hotplug-spec
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

CONFIG_CHECKING covered some debugging code used in the early times
of the port. But it wasn't even SMP safe for quite some time
and the bugs it checked for seem to be gone.

This patch removes all the code to verify GS at kernel entry. There
haven't been any new bugs in this area for a long time.

Previously it also covered the sysctl for the page fault tracing.
That didn't make much sense because that code was unconditionally
compiled in. I made that a boot option now because it is typically
only useful at boot.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The logging for boot errors was turned off because it was broken
on some AMD systems. But give Intel EM64T systems a chance because they are
supposed to be correct there.

The advantage is that there is a chance to actually log uncorrected
machine checks after the reset.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs.  The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)

The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports.  So the old code just assumed all, which would
lead to this memory wastage.

This implements some new heuristics:

 - If the BIOS specified disabled CPUs in the ACPI/mptables assume they
   can be enabled later (this is bending the ACPI specification a bit,
   but seems like a obvious extension)
 - The user can overwrite it with a new additionals_cpus=NUM option
 - Otherwise use half of the available CPUs or 2, whatever is more.

Cc: ashok.raj@intel.com
Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Don't log machine check events left over from boot.  Too many BIOSes leave
bogus events in there.

This unfortunately also makes it impossible to log events that caused a
reboot.  For people with non broken BIOS there is mce=bootlog
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This works around the too fast timer seen on some ATI boards.

I don't feel confident enough about it yet to enable it by default, but give
users the option.

Patch and debugging from Christopher Allen Wing <wingc@engin.umich.edu>, with
minor tweaks (renamed the option and documented it)
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!