The driver does not always use the same timing for what looks like
the same operations.

- DCR0
  Use the same udelay everywhere for reset. Upper bound is 100 us.
- DCR9
  Use 5us delay for srom clock. 1us delay for phy_write_1bit (writes
  PHY_DATA_[01]) are not changed as they stay withing a 2,5MHz MDIO
  clock range.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix mixed space and tabs.

Put bpf_jit_load_*[] externs into bpf_jit.h

"while(0)" --> "while (0)"
"COND (X)" --> "COND(X)"
Document branch offset calculations, and bpf_error's return
sequence.

Document the reason we need to emit three nops between the
%y register write and the divide instruction.

Remove erroneous trailing semicolons from emit_read_y() and
emit_write_y().

Based upon feedback from Sam Ravnborg.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct conventions comments.  %o4 and %o5 were swapped,
%g3 was not documented.

Use r_TMP instead of r_SKB_DATA + r_OFF where possible in
assembler stubs.

Correct discussion of %o4 and %o5 in one of bpf_jit_compile()'s
comments.

Based upon feedback from Richard Mortimer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compared with previous chipsets, it needs no special action trough the
jumbo{enable/disable} helpers to operate with jumbo frames.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

Put some settings of 8111f into one function which may be reused.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>

Signed-off-by: NHayes Wang <hayeswang@realtek.com>

New chipsets need it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>

Adjust r810x_pll_power_down, r810x_pll_power_up, and r8168_pll_power_up.
Always power up device during rtl_open. For r810x, turn off more power
when the WOL is disabled.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>

The new 84xx stopped flying below the radars.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Suggested by Hayes.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Fix printk format warning (from i386 build):

drivers/net/hippi/rrunner.c:146:9: warning: format '%08llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc:	linux-hippi@sunsite.dk
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the drivers in drivers/net/can/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-can@vger.kernel.org
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Make cgw_list static to remove the following sparse warning:
net/can/gw.c:69:1: warning: symbol 'cgw_list' was not declared.
Should it be static?
Signed-off-by: NDaniel Baluta <dbaluta@ixiacom.com>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Commit b82d1bb4 inadvertendly placed unrelated new code between
TCPCB_EVER_RETRANS and TCPCB_RETRANS and the other macros that refer
to the sacked field in the struct tcp_skb_cb (probably because there
was a misleading empty line there). This commit fixes up the
formatting so that all macros related to the sacked field are adjacent
again.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 109d2446

    "net/mlx4_en: Set max rate-limit for a TC"

introduced 64 bit math operations into mlx4_en_dcbnl_ieee_setmaxrate()

causing the following final link failure on an x86_32 allmodconfig

  ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx4/mlx4_en.ko] undefined!

Convert it to use div_u64() instead.

Cc: Amir Vadai <amirv@mellanox.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/atheros/atlx/atl1.c
	drivers/net/ethernet/atheros/atlx/atl1.h

Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds FDB bridge ops to the macvlan device passthru mode.
Additionally a flags field was added and a NOPROMISC bit to
allow users to use passthru mode without the driver calling
dev_set_promiscuity(). The flags field is a u16 placed in a
4 byte hole (consuming 2 bytes) of the macvlan_dev struct.

We want to do this so that the macvlan driver or stack
above the macvlan driver does not have to process every
packet. For the use case where we know all the MAC addresses
of the endstations above us this works well.

This patch is a result of Roopa Prabhu's work. Follow up
patches are needed for VEPA and VEB macvlan modes.

v2: Change from distinct nopromisc mode to a flags field to
    configure this. This avoids the tendency to add a new
    mode every time we need some slightly different behavior.
v3: fix error in dev_set_promiscuity and add change and get
    link attributes for flags.

CC: Roopa Prabhu <roprabhu@cisco.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The UTA table was being set to the functional equivalent of promiscuous
mode.  This was resulting in traffic from the virtual function being
flooded onto the wire and the PF device. This resulted in additional
overhead for VF traffic sent to the network and in the case of traffic
sent to the PF or another VF resulted in unwanted packets on the wire.

This was actually not the intended behavior. Now that we can program
the embedded switch correctly we can remove this snippit of code. Users
who want to support this should configure the FDB correctly using the
FDB ops.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows RAR table updates while in promiscuous. With
SR-IOV enabled it is valuable to allow the RAR table to
be updated even when in promisc mode to configure forwarding
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable FDB ops on ixgbe when in SR-IOV mode.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is useful to be able to monitor for FDB events in user space.
This patch adds support to generate netlink events when a change
is made to a device supporting the FDB ops.

This brings embedded switches inline with the SW net/bridge which
triggers events on FDB updates as well.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a generic dump routine drivers can call. It
should be sufficient to handle any bridging model that
uses the unicast address list. This should be most SR-IOV
enabled NICs.

v2: return error on nlmsg_put and use -EMSGSIZE instead
    of -ENOMEM this is inline other usages
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a dev_uc_add_excl() and dev_mc_add_excl() calls
similar to the original dev_{uc|mc}_add() except it sets
the global bit and returns -EEXIST for duplicat entires.

This is useful for drivers that support SR-IOV, macvlan
devices and any other devices that need to manage the
unicast and multicast lists.

v2: fix typo UNICAST should be MULTICAST in dev_mc_add_excl()

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds two new flags NTF_MASTER and NTF_SELF that can
now be used to specify where PF_BRIDGE netlink commands should
be sent. NTF_MASTER sends the commands to the 'dev->master'
device for parsing. Typically this will be the linux net/bridge,
or open-vswitch devices. Also without any flags set the command
will be handled by the master device as well so that current user
space tools continue to work as expected.

The NTF_SELF flag will push the PF_BRIDGE commands to the
device. In the basic example below the commands are then parsed
and programmed in the embedded bridge.

Note if both NTF_SELF and NTF_MASTER bits are set then the
command will be sent to both 'dev->master' and 'dev' this allows
user space to easily keep the embedded bridge and software bridge
in sync.

There is a slight complication in the case with both flags set
when an error occurs. To resolve this the rtnl handler clears
the NTF_ flag in the netlink ack to indicate which sets completed
successfully. The add/del handlers will abort as soon as any
error occurs.

To support this new net device ops were added to call into
the device and the existing bridging code was refactored
to use these. There should be no required changes in user space
to support the current bridge behavior.

A basic setup with a SR-IOV enabled NIC looks like this,

          veth0  veth2
            |      |
          ------------
          |  bridge0 |   <---- software bridging
          ------------
               /
               /
  ethx.y      ethx
    VF         PF
     \         \          <---- propagate FDB entries to HW
     \         \
  --------------------
  |  Embedded Bridge |    <---- hardware offloaded switching
  --------------------

In this case the embedded bridge must be managed to allow 'veth0'
to communicate with 'ethx.y' correctly. At present drivers managing
the embedded bridge either send frames onto the network which
then get dropped by the switch OR the embedded bridge will flood
these frames. With this patch we have a mechanism to manage the
embedded bridge correctly from user space. This example is specific
to SR-IOV but replacing the VF with another PF or dropping this
into the DSA framework generates similar management issues.

Examples session using the 'br'[1] tool to add, dump and then
delete a mac address with a new "embedded" option and enabled
ixgbe driver:

# br fdb add 22:35:19:ac:60:59 dev eth3
# br fdb
port    mac addr                flags
veth0   22:35:19:ac:60:58       static
veth0   9a:5f:81:f7:f6:ec       local
eth3    00:1b:21:55:23:59       local
eth3    22:35:19:ac:60:59       static
veth0   22:35:19:ac:60:57       static
#br fdb add 22:35:19:ac:60:59 embedded dev eth3
#br fdb
port    mac addr                flags
veth0   22:35:19:ac:60:58       static
veth0   9a:5f:81:f7:f6:ec       local
eth3    00:1b:21:55:23:59       local
eth3    22:35:19:ac:60:59       static
veth0   22:35:19:ac:60:57       static
eth3    22:35:19:ac:60:59       local embedded
#br fdb del 22:35:19:ac:60:59 embedded dev eth3

I added a couple lines to 'br' to set the flags correctly is all. It
is my opinion that the merit of this patch is now embedded and SW
bridges can both be modeled correctly in user space using very nearly
the same message passing.

[1] 'br' tool was published as an RFC here and will be renamed 'bridge'
    http://patchwork.ozlabs.org/patch/117664/

Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for
valuable feedback, suggestions, and review.

v2: fixed api descriptions and error case with both NTF_SELF and
    NTF_MASTER set plus updated patch description.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prevent interrupts lost they should be dropped only if
they are scheduled via napi interfaces. In other case, there is
exists situation when napi handler process TX interrupt, stay in
RX processing and in that moment any other interrupt received.
Then before this patch TX bit in ISR will be cleaned, napi
schedule will not occur in case of currently processing event and
TX interrupt definitely will be lost.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the rx/tx handled inside napi handler, the cycle is
not needed now, because only the rx/tx need such kind of
processing.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unfortunately it is not clear from code is usage of
IMR register possible or not. So, to prevent possible
side-effects of reading this register i prefer store
interrupts enable flag separately.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function should be used later to set/remove proper
bits in imr to disable only rx ints.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Looks like direct writes to IMR register is not good idea,
because there are exist functions to make this work.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the tx ints processing same as rx ones via napi.
The idea got from e1000. The interrupt disabling is
still not fine grained.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is first step, here there is no fine interrupt
disabling which cause TX/ERR interrupts stalling when
RX scheduled ints processed.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove rx from unlikely optimization in case of rx is very
likely thing for network card. This also reduce code a bit.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sending general queries was implemented as an optimisation to speed
up convergence on start-up.  In order to prevent interference with
multicast routers a zero source address has to be used.

Unfortunately these packets appear to cause some multicast-aware
switches to misbehave, e.g., by disrupting multicast packets to us.

Since the multicast snooping feature still functions without sending
our own queries, this patch will change the default to not send
queries.

For those that need queries in order to speed up convergence on start-up,
a toggle is provided to restore the previous behaviour.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As it stands when we discover that a real querier (one that queries
with a non-zero source address) we stop querying.  However, even
after said querier has fallen off the edge of the earth, we will
never restart querying (unless the bridge itself is restarted).

This patch fixes this by kicking our own querier into gear when
the timer for other queriers expire.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the helper br_multicast_start_querier so that
the code which starts the queriers in br_multicast_toggle can
be reused elsewhere.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>