mop500_snowball_ethernet_clock_enable() provided a means to enable a
clock which was used for the SMSC911x Ethernet device on Snowball. It
was merely a stand-in until the driver was common clk compliant. Now
that it is, this can be removed for both DT and ATAGs booting.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Ironically, in order to remove lots of the auxdata assignments, we have
to add just one more. A lot of them require DMA information to be passed
into clients for DMA channel allocation, but we now have this capability
in Device Tree. However, the DMA40 driver still relies on a reverse table
look-up to obtain DMA addresses. Until all of the clients are converted,
over to the new API, we're stuck with this.

Also, now the DMA40 has been DT:ed, there's no requirement to register
it using traditional methods, so let's remove it.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

With the PRCMU out of the way, nothing outside of mach-ux500
uses mach/irqs.h any more, so we can make it a local header file,
including the two sub-headers.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This header file only contains platform data structure definitions,
so it's straightforward to move.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[Delete one include rather than move it]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This fixes a regression introduced by common clk enablement.

On some u8500 based boards, the FMSC clock which is usually used
for flash, is wired up to the SMSC911x Ethernet driver. However,
the SMSC911x doesn't have common clk support yet, rendering it
unusable. Prior to the introduction of common clk the FMSC clock
was default on; however, common clk disables all clocks by default
and insists drivers take responsibility to enable theirs.

This fix enables the FMSC clock on Snowball, subsequently turning
on the SMSC911x Ethernet chip. It will be removed when the driver
is compatible with common clk.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We now initialise the PCM driver through the MSP DAI, so there is
no need to register it though platform code anymore. This patch
strips out all PCM platform registration.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To aid the kernel in its effort to move to DT only booting, we're
transplanting all Device Tree related code to cpu-db8500 which will
remain persistent throughout the transition. This change paths the
way for complete removal of board-mop500, which will be done once
the all DMA settings are moved into the respective DT source files.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The 'msp' board file does more than just register MSP devices. It
also registers some other components necessary to get audio working
on ux500 based platforms; such as the PCM and Machine Drivers. For
that reason we're changing the filename to be more encompassing -
'audio'.
Acked-by: NOla Lilja <ola.o.lilja@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

It isn't currently possible to pass all platform specific configuration
though Device Tree. Thinks like device names used in the clock
infrastructure, call-backs and DMA information have to be passed in via
AUXDATA structures and the MSP is no exception. Here we're passing DMA
settings.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

We've done this before and it worked well last time. Here we're
duplicating a complex registration function to ease the process
of enabling it for Device Tree. As there are quite a few steps
taken during the registration process, it makes sense to break
them up into more manageable chunks. This patch will aid us.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch contains a couple of general MSP clean-ups pertaining to
layout changes and changing functions to be void instead of int instead
of regardlessly returning '0'.
Acked-by: NOla Lilja <ola.o.lilja@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There are four SDIs on the HREF, as opposed to the original two
enabled on Snowball. To get them working we have to pass their DMA
information in the same was as we need with the other two.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

When booting with Device Tree we need a way to call-back to the
DB8500 PMU IRQ handler. This is necessary because the two CPU
IRQ lines are muxed together on the DB8500 chip. The DB8500
PMU IRQ handler contains logic to pass over to the other core
in the case of IRQ_NONE. This patch allows the DB8500 PMU IRQ
handler to be passed to Perf through platform data.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Allow proper initialisation for MMC via the mmci driver
for the Snowball low-cost development board using DT. At
the moment we continue to use DMA setup from platform code.
Once the DMA generic DT bindings have been completed we
can then port the remainder over to DT.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

ST-Ericsson uses User Interface Boards to extend functionality of
some of their development boards. However, these aren't compatible
with all the supported boards found in Mainline (Snowball for
instance). This patch ensures that the UIBs are only probed on
boards which can actually support them. This in turn saves lots of
unnecessary error messages normally found in Snowball's boot log.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

During Device Tree enablement it is necessary to remove
<hw_component>_add_<device> calls one at at time, as and when particular
devices are DT enabled. This patch provides a temporary solution. Once
the new *of_init_devices function has been fully unpopulated it will be
removed again.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This converts the Ux500 family to use the pinctrl driver for
configuring pins.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This updates the Ux500 pin handling to take much more care when
applying pin settings for different platforms and peripherals.
This is an accumulation of a longer history of updates to the
MOP500 family pin file.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

AB8500 GPIO1 is the base of AB8500 gpio number too.
Signed-off-by: NPhilippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch provides a means for any device within ux500
platform code to allocate its own parent. This is particularly
prudent with the introduction of /sys/devices/socX, as a
device can now proclaim to be integral part of an SoC, rather
than a more generic platform device. Latter patches make good
use of this functionality.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This is a more complete list of the MOP500 GPIO pins, especially
for those used with the Snowball board. Sort GPIO number in
falling number order so there is some structure to this file.
Fix some whitespace issues in the process.

Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Properly support the correct SDI-init sequence on the
ST-Ericsson HREFv60 and later boards in order to get
support for SD cards.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Do more work in the per-machine init calls instead of customizing
each init call.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

With SDI support for the Snowball we can boot from the
SD card.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>

This is the board support patch for ab8500 gpio driver
on mach-ux500.Patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: NBibek Basu <bibek.basu@stericsson.com>
[Modify for header file placement]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The HREFv60 variant of the MOP500 family of boards remove the
external GPIO expander and route these pins back to some of the
readily available internal GPIO pins instead.

Based on a patch by Bibek Basu <bibek.basu@stericsson.com> for
an internal kernel version.

Cc: Bibek Basu <bibek.basu@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Split off pin definitions for the MOP500 board family to its
own file.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Proximity sensor is managed as an input event (SW_PROXIMITY).
Signed-off-by: NPhilippe Langlais <philippe.langlais@linaro.org>
[Named GPIO pin]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ST-UIB contains a matrix keypad interfaced with the
STMPE1601 port expander and a ROHM BU2101 touch panel.
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add support for dynamic detection of the UIB used (at the cost of one i2c error
on the lesser-used UIB) and also provide an override via a command line
parameter if needed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Move keylayouts to a dedicated file and plug these keylayouts
for input platform data. This will make addition of new and custom
keylayouts localized.
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NHanumath Prasad <hanumath.prasad@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>