We never set "slots" in this function.

Fixes: a9380b0f ("drivers: net: xgene: Add support for Jumbo frame")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

>From what I can tell, spin_lock(&priv->lock) is not needed, since the
phy_ethtool_ksettings_set call is not given the priv struct.

phy_start_aneg takes the phydev->lock. Calls to phy_adjust_link
from phy_state_machine also takes the phydev->lock.

[   13.718319] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
[   13.726717] in_atomic(): 1, irqs_disabled(): 0, pid: 1307, name: ethtool
[   13.742115] Hardware name: Axis ARTPEC-6 Platform
[   13.746829] [<80110568>] (unwind_backtrace) from [<8010c2bc>] (show_stack+0x18/0x1c)
[   13.754575] [<8010c2bc>] (show_stack) from [<80433484>] (dump_stack+0x80/0xa0)
[   13.761801] [<80433484>] (dump_stack) from [<80145428>] (___might_sleep+0x108/0x170)
[   13.769554] [<80145428>] (___might_sleep) from [<806c9b50>] (mutex_lock+0x24/0x44)
[   13.777128] [<806c9b50>] (mutex_lock) from [<8050cbc0>] (phy_start_aneg+0x1c/0x13c)
[   13.784783] [<8050cbc0>] (phy_start_aneg) from [<8050d338>] (phy_ethtool_ksettings_set+0x98/0xd0)
[   13.793656] [<8050d338>] (phy_ethtool_ksettings_set) from [<80517adc>] (stmmac_ethtool_set_link_ksettings+0xa0/0xb4)
[   13.804184] [<80517adc>] (stmmac_ethtool_set_link_ksettings) from [<805c5138>] (ethtool_set_settings+0xd4/0x13c)
[   13.814358] [<805c5138>] (ethtool_set_settings) from [<805c9718>] (dev_ethtool+0x13c4/0x211c)
[   13.822882] [<805c9718>] (dev_ethtool) from [<805dc7c0>] (dev_ioctl+0x480/0x8e0)
[   13.830291] [<805dc7c0>] (dev_ioctl) from [<80260e34>] (do_vfs_ioctl+0x94/0xa00)
[   13.837699] [<80260e34>] (do_vfs_ioctl) from [<802617dc>] (SyS_ioctl+0x3c/0x60)
[   13.845011] [<802617dc>] (SyS_ioctl) from [<801088bc>] (__sys_trace_return+0x0/0x10)
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.

Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
 max_sec_before_overflow = max_counter_val / rftclk_freq.

Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.

Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.

Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.

This patch splits CPTS initialization and deinitialization on two parts:

- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;

- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.

As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries.  When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: NWingMan Kwok <w-kwok2@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpts now is left enabled after unregistration.
Hence, disable it in cpts_unregister().
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ptp clock registered before spinlock, which is protecting it, and
before timecounter and cyclecounter initialization in cpts_register().

So, ensure that ptp clock is registered the last, after everything
else is done.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two issues with TI CPTS code which are reproducible when TI
CPSW ethX device passes few up/down iterations:
- cpts refclk prepare counter continuously incremented after each
up/down iteration;
- devm_clk_get(dev, "cpts") is called many times.

Hence, fix these issues by using clk_disable_unprepare() in
cpts_clk_release() and skipping devm_clk_get() if cpts refclk has been
acquired already.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will provide more flexibility in changing CPTS internals and also
required for further changes.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also
present as part of NETCP on TI Keystone 2 SoCs. So, It's required
to enable build of CPTS for both this drivers and this can be
achieved by allowing CPTS to be built separately.

Hence, allow cpts to be built separately and convert it to be
a module as both CPSW and NETCP drives can be built as modules.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to readl/writel_relaxed() APIs, because this is recommended
API and the CPTS IP is reused on Keystone 2 SoCs
where LE/BE modes are supported.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.

1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success.  After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.

2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.

3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device().  A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.

4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.

5. 1 stats context is reserved when the RDMA driver registers.  MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.

6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.

v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver register function with firmware consists of passing version
information and registering for async events.  To support the RDMA driver,
the async events that we need to register may change.  Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device supports RDMA, we'll setup network default rings so that
there are enough minimum resources for RDMA, if possible.  However, the
user can still increase network rings to the max if he wants.  The actual
RDMA resources won't be reserved until the RDMA driver registers.

v2: Fix compile warning when BNXT_CONFIG_SRIOV is not set.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA.  The earlier workaround code of capping the rings by the
statistics context is removed.

When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources.  Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that MSIX is enabled in bnxt_init_one(), resources may be allocated by
the RDMA driver before the network device is opened.  So we cannot do
function reset in bnxt_open() which will clear all the resources.

The proper place to do function reset now is in bnxt_init_one().
If we get AER, we'll do function reset as well.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To better support the new RDMA driver, we need to move pci_enable_msix()
from bnxt_open() to bnxt_init_one().  This way, MSIX vectors are available
to the RDMA driver whether the network device is up or down.

Part of the existing bnxt_setup_int_mode() function is now refactored into
a new bnxt_init_int_mode().  bnxt_init_int_mode() is called during
bnxt_init_one() to enable MSIX.  The remaining logic in
bnxt_setup_int_mode() to map the IRQs to the completion rings is called
during bnxt_open().

v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By refactoring existing code into this new function.  The new function
will be used in subsequent patches.

v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to how we handled exiting VLAN mode, move the logic
in i40e_vsi_add_vlan into i40e_sync_vsi_filters. Extract this logic into
its own function for ease of understanding as it will become quite
complex.

The new function, i40e_correct_mac_vlan_filters() correctly updates all
filters for when we need to enter VLAN mode, exit VLAN mode, and also
enforces the PVID when assigned.

Call i40e_correct_mac_vlan_filters from i40e_sync_vsi_filters passing it
the number of active VLAN filters, and the two temporary lists.

Remove the function for updating VLAN=0 filters from i40e_vsi_add_vlan.

The end result is that the logic for entering and exiting VLAN mode is
in one location which has the most knowledge about all filters. This
ensures that we always correctly have the non-VLAN filters assigned to
VID=0 or VID=-1 regardless of how we ended up getting to this result.

Additionally this enforces the PVID at sync time so that we know for
certain that an assigned PVID results in only filters with that PVID
will be added to the firmware.

Change-ID: I895cee81e9c92d0a16baee38bd0ca51bbb14e372
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.

Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.

It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.

(a) we're adding a new PVID
  In this case, if we already had VLAN filters the VSI is knocked
  offline so we don't need to worry about pre-existing VLAN filters

(b) we're replacing an existing PVID
  In this case, we can't have any VLAN filters except those with the old
  PVID which we already take care of manually.

(c) we're removing an existing PVID
  Similarly to above, we can't have any existing VLAN filters except
  those with the old PVID which we already take care of correctly.

Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.

Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A future refactor of how the PF assigns a PVID to a VF will want to be
able to add and remove a block of filters by VLAN without worrying about
accidentally triggering the accounting for I40E_VLAN_ANY. Additionally
the PVID assignment would like to be able to batch several changes under
one use of the mac_filter_hash_lock.

Factor out the addition and deletion of a VLAN on all MACs into their
own function which i40e_vsi_(add|kill)_vlan can use. These new functions
expect the caller to take the hash lock, as well as perform any
necessary accounting for updating I40E_VLAN_ANY filters if we are now
operating under VLAN mode.

Change-ID: If79e5b60b770433275350a74b3f1880333a185d5
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a subtle issue with the code for converting VID=-1 filters into VID=0
filters when adding a new VLAN. Previously the code deleted the VID=-1
filter, and then added a new VID=0 filter. In the rare case that the
addition fails due to -ENOMEM, we end up completely deleting the filter
which prevents recovery if memory pressure subsides. While it is not
strictly an issue because it is likely that memory issues would result
in many other problems, we shouldn't delete the filter until after the
addition succeeds.

Change-ID: Icba07ddd04ecc6a3b27c2e29f2c1c8673d266826
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current caller of i40e_update_filter_state incorrectly passes
aq_ret, an i40e_status variable, instead of the expected aq_err. This
happens to work because i40e_status is actually just a typedef integer,
and 0 is still the successful return. However i40e_update_filter_state
has special handling for ENOSPC which is currently being ignored.

Also notice that firmware does not update the per-filter response for
many types of errors, such as EINVAL. Thus, modify the filter setup so
that the firmware response memory is pre-set with I40E_AQC_MM_ERR_NO_RES.

This enables us to refactor i40e_update_filter_state, removing the need
to pass aq_err and avoiding a need for having 3 different flows for
checking the filter state.

The resulting code for i40e_update_filter_state is much simpler, only
a single loop and we always check each filter response value every time.
Since we pre-set the response value to match our expected error this
correctly works for all success and error flows.

Change-ID: Ie292c9511f34ee18c6ef40f955ad13e28b7aea7d
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previous code refactors have accidentally caused issues with the
counting of active_filters. Avoid similar issues in the future by simply
re-counting the active filters every time after we handle add and delete
of all the filters. Additionally this allows us to simplify the check
for when we exit promiscuous mode since we can combine the check for
failed filters at the same time.

Additionally since we recount filters at the end we need to set
vsi->promisc_threshold as well.

The resulting code takes a bit longer since we do have to loop over
filters again. However, the result is more readable and less likely to
become incorrect due to failed accounting of filters in the future.
Finally, this ensures that it is not possible for vsi->active_filters to
ever underflow since we never decrement it.

Change-ID: Ib4f3a377e60eb1fa6c91ea86cc02238c08edd102
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A product decision has been made to defeature detection of PTP frames
over L4 (UDP) on the XL710 MAC. Do not advertise support for L4
timestamping.

Change-ID: I41fbb0f84ebb27c43e23098c08156f2625c6ee06
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The service task lock was being set in the scheduling function, not the
actual service task. This would potentially leave the bit set for a long
time before the task actually ran. Furthermore, if the service task
takes too long, it calls the schedule function to reschedule itself -
which would fail to take the lock and do nothing.

Instead, set and clear the lock bit in the service task itself. In the
process, get rid of the i40e_service_event_complete() function, which is
really just two lines of code that can be put right in the service task
itself.

Change-ID: I83155e682b686121e2897f4429eb7d3f7c669168
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Depending on external PHY type, register access method should be
different. Clause22 or Clause45 can be chosen for different PHYs.
Implemented functions apply correct access method for used device.

Change-ID: If39d5f0da9c0b905a8cbdc1ab89885535e7d0426
Signed-off-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds adminq support for Forward Error
Correction ("FEC")for 25g products.

Change-ID: Iaff4910737c239d2c730e5c22a313ce9c37d3964
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJacek Naczyk <jacek.naczyk@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for 25G devices - defines and data structures.

One tricky part here is that the firmware support for these
Devices introduces a mismatch between the PHY type enum and
the bitfields for the phy types.

This change creates a macro and uses it to increment the 25G
PHY values when creating 25G bitfields.

Change-ID: I69b24d837d44cf9220bf5cb8dd46c5be89ce490b
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace the %d specifier used for printing vsi->active_filters and
vsi->promisc_threshold with an unsigned %u format specifier. While it is
unlikely in practice that these values will ever reach such a large
number they are unsigned values and thus should not be interpreted as
negative numbers.

Change-ID: Iff050fad5a1c8537c4c57fcd527441cd95cfc0d4
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Before this patch "ethtool -p" was not blinking the LEDs on boards
with 1G BaseT PHYs.

This commit identifies 1G BaseT boards as having the LEDs connected
to the MAC. Also, renamed the flag to be more descriptive of usage.
The flag is now I40E_FLAG_PHY_CONTROLS_LEDS.

Change-ID: I4eb741da9780da7849ddf2dc4c0cb27ffa42a801
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The netdev->dev_addr MAC filter already exists in the
MAC/VLAN hash table, as it is added when we configure
the netdev in i40e_configure_netdev. Because we already
know that this address will be updated in the
hash_for_each loops, we do not need to handle it
specially. This removes duplicate code and simplifies
the i40e_vsi_add_vlan and i40e_vsi_kill_vlan functions.
Because we know these filters must be part of the
MAC/VLAN hash table, this should not have any functional
impact on what filters are included and is merely a code
simplification.

Change-ID: I5e648302dbdd7cc29efc6d203b7019c11f0b5705
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the function i40e_napi-poll() returns 0 when it clean completely
the Rx rings, but this foul budget accounting in core code.

Fix this by returning the actual work done, capped to budget - 1, since
the core doesn't allow to return the full budget when the driver modifies
the NAPI status

This is based on a similar change that was made for the ixgbe driver by
Paolo Abeni.

Change-ID: Ic3d93ad2fa2fc8ce3164bc461e69367da0f9173b
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous commit 53cb6e9e ("i40e: Removal of workaround for simple
MAC address filter deletion") removed a workaround for some
firmware versions which was reported to not be necessary in production
NICs. Unfortunately this workaround is necessary in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+ (8086:1583).

Without this patch, the mentioned NICs with current firmware exhibit
issues when adding VLANs, as outlined by the following reproduction:

  $modprobe i40e
  $ip link set <device> up
  $ip link add link <device> vlan100 type vlan id 100
  $dmesg | tail
  <snip>
  kernel: i40e 0000:82:00.0: Error I40E_AQ_RC_EINVAL adding RX
filters on PF, promiscuous mode forced on

This results in filters being marked as FAILED and setting the device in
promiscuous mode.

The root cause of receiving the -EINVAL error response appears to be due
to a conflict with the default MAC filter which still exists on the
default firmware for this device. Attempting to add a new VLAN filter on
the default MAC address conflicts with the IGNORE_VLAN setting on the
default rule.

Change-ID: I4d8f6d48ac5f60cfe981b3baad30eb4d7c170d61
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e_txd_use_count function was fast but confusing. In the comments,
it even admits that it's ugly. So replace it with a new function that is
(very) slightly faster and has extensive commenting to help the thicker
among us (including the author, who will forget in a week) understand
how it works.

Change-ID: Ifb533f13786a0bf39cb29f77969a5be2c83d9a87
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes the driver log link speed change. Before applying the
patch link messages were printed only on state change. Now message is
printed when link is brought up or down and when speed changes.

Change-ID: Ifbee14b4b16c24967450b3cecac6e8351dcc8f74
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>