N group

Add to_irq() function to onvert gpio to irq for external interrupt
group (GPN).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The usb-host clock was using the wrong define (the SCLK enable for the
usb-host-bus) to change the HCLK register instead of the HCLK_UHOST bit.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

A few typos seems to have sneaked into the HCLK gate defines, causing the
usb host clock to not get enabled. Fix them according to the reference
manual and throw in the 3d accel bit for good measure.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge branch 'next-mini2440' into next-s3c

This patch introduces the Openmoko GTA02 machine definition.

Much of the code is based on Harald Welte's work, although it
has been largely rewritten several times.

This is intended to be the minimum machine definition to boot and
be able to run a rootfs from NAND on GTA02 / FreeRunner.  It does
not bring up the framebuffer / Glamo and lacks many other peripheral
drivers from outside the SoC.  But once we have this basis in
mainline kernel, we will be able to introduce the other drivers
and add them here.

Thanks to Sven Rebhan <odinshorse@googlemail.com> for his fixes to this
patch (Kconfig and defconfig files).
Signed-off-by: NAndy Green <andy@warmcat.com>
Signed-off-by: NNelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: Fix the GPIO definitions]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch provides initial support for CPU frequency scaling on the
Samsung S3C ARM processors. Currently only S3C6410 processors are
supported, though addition of another data table with supported clock
rates should be sufficient to enable support for further CPUs.

Use the regulator framework to provide optional support for DVFS in
the S3C cpufreq driver. When a software controllable regulator is
configured the driver will use it to lower the supply voltage when
running at a lower frequency, giving improved power savings.

When regulator support is disabled or no regulator can be obtained
for VDDARM the driver will fall back to scaling only the frequency.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This allows the S3C64XX IIS drivers to be converted to the standard
driver model and allows fixes there for problems with attempting to
acquire the clocks for the IIS blocks via the clock API.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove duplicated #include in arch/arm/mach-s3c2410/usb-simtec.c.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The resume_mask wasn't being checked in vic_set_wake()
to see if the IRQ was a valid wakeup source.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This was missed in the DMA changes during the s3c24xx
updates in commit 8970ef47.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove duplicate mach headers for gpio.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Just a working, starting point config file for the board.
Signed-off-by: NMichel Pollet <buserror@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Also explains why the touchscreen support is not present,
and were to find a working one...
Signed-off-by: NMichel Pollet <buserror@gmail.com>
[ben-linux@fluff.org: Fix header description]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The MINI2440 is a chinese made s3c2440 development board with
a large set of peripherals.
This patch provides machine support for almost all the features
of the board.

Since it can come with various "options" fitted, a kernel parameter
is used to specify the lcd size, backlight control and touchscreen.
Signed-off-by: NMichel Pollet <buserror@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] fix compile error in arch/ia64/mm/extable.c

Merge branch 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  timers: Logic to move non pinned timers
  timers: /proc/sys sysctl hook to enable timer migration
  timers: Identifying the existing pinned timers
  timers: Framework for identifying pinned timers
  timers: allow deferrable timers for intervals tv2-tv5 to be deferred

Fix up conflicts in kernel/sched.c and kernel/timer.c manually

Merge branch 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevent: export register_device and delta2ns
  clockevents: tick_broadcast_device can become static

Merge branch 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clocksource: prevent selection of low resolution clocksourse also for nohz=on
  clocksource: sanity check sysfs clocksource changes

Merge branch 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ntp: fix comment typos
  ntp: adjust SHIFT_PLL to improve NTP convergence

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1244 commits)
  pkt_sched: Rename PSCHED_US2NS and PSCHED_NS2US
  ipv4: Fix fib_trie rebalancing
  Bluetooth: Fix issue with uninitialized nsh.type in DTL-1 driver
  Bluetooth: Fix Kconfig issue with RFKILL integration
  PIM-SM: namespace changes
  ipv4: update ARPD help text
  net: use a deferred timer in rt_check_expire
  ieee802154: fix kconfig bool/tristate muckup
  bonding: initialization rework
  bonding: use is_zero_ether_addr
  bonding: network device names are case sensative
  bonding: elminate bad refcount code
  bonding: fix style issues
  bonding: fix destructor
  bonding: remove bonding read/write semaphore
  bonding: initialize before registration
  bonding: bond_create always called with default parameters
  x_tables: Convert printk to pr_err
  netfilter: conntrack: optional reliable conntrack event delivery
  list_nulls: add hlist_nulls_add_head and hlist_nulls_del
  ...

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
  powerpc: Fix bug in move of altivec code to vector.S
  powerpc: Add support for swiotlb on 32-bit
  powerpc/spufs: Remove unused error path
  powerpc: Fix warning when printing a resource_size_t
  powerpc/xmon: Remove unused variable in xmon.c
  powerpc/pseries: Fix warnings when printing resource_size_t
  powerpc: Shield code specific to 64-bit server processors
  powerpc: Separate PACA fields for server CPUs
  powerpc: Split exception handling out of head_64.S
  powerpc: Introduce CONFIG_PPC_BOOK3S
  powerpc: Move VMX and VSX asm code to vector.S
  powerpc: Set init_bootmem_done on NUMA platforms as well
  powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
  powerpc/mm: Fix some SMP issues with MMU context handling
  powerpc: Add PTRACE_SINGLEBLOCK support
  fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
  powerpc/virtex: Add ml510 reference design device tree
  powerpc/virtex: Add Xilinx ML510 reference design support
  powerpc/virtex: refactor intc driver and add support for i8259 cascading
  powerpc/virtex: Add support for Xilinx PCI host bridge
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator/max1586: fix V3 gain calculation integer overflow
  regulator/max1586: support increased V3 voltage range
  regulator: lp3971 - fix driver link error when built-in.
  LP3971 PMIC regulator driver (updated and combined version)
  regulator: remove driver_data direct access of struct device
  regulator: Set MODULE_ALIAS for regulator drivers
  regulator: Support list_voltage for fixed voltage regulator
  regulator: Move regulator drivers to subsys_initcall()
  regulator: build fix for powerpc - renamed show_state
  regulator: add userspace-consumer driver
  Maxim 1586 regulator driver

ad6561df ("module: trim exception table on init
free.") put a bogus trim_init_extable() function into ia64 which didn't compile.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NTony Luck <tony.luck@intel.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (22 commits)
  nilfs2: support contiguous lookup of blocks
  nilfs2: add sync_page method to page caches of meta data
  nilfs2: use device's backing_dev_info for btree node caches
  nilfs2: return EBUSY against delete request on snapshot
  nilfs2: modify list of unsupported features in caveats
  nilfs2: enable sync_page method
  nilfs2: set bio unplug flag for the last bio in segment
  nilfs2: allow future expansion of metadata read out via get info ioctl
  NILFS2: Pagecache usage optimization on NILFS2
  nilfs2: remove nilfs_btree_operations from btree mapping
  nilfs2: remove nilfs_direct_operations from direct mapping
  nilfs2: remove bmap pointer operations
  nilfs2: remove useless b_low and b_high fields from nilfs_bmap struct
  nilfs2: remove pointless NULL check of bpop_commit_alloc_ptr function
  nilfs2: move get block functions in bmap.c into btree codes
  nilfs2: remove nilfs_bmap_delete_block
  nilfs2: remove nilfs_bmap_put_block
  nilfs2: remove header file for segment list operations
  nilfs2: eliminate removal list of segments
  nilfs2: add sufile function that can modify multiple segment usages
  ...

On Thu, May 28, 2009 at 10:59 AM, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote:
> On Thu, May 28, 2009 at 07:15:16AM +0200, Philipp Zabel wrote:
>> The V3 regulator can be configured with an external resistor
>> connected to the feedback pin (R24 in the data sheet) to
>> increase the voltage range.
>>
>> For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
>> V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
>>
>> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
>
> Looks good.
>
> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Thanks, but it turns out I hit a 32 bit integer overflow in
the gain calculation. I'd like to mend that with the following
patch. Now max_uV could be increased up to 4.294 V, enough to
charge LiPo cells.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.

For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

lp3971_i2c_remove' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.devexit.text' of drivers/built-in.o
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Several of the regulator drivers didn't have MODULE_ALIAS so couldn't be
auto loaded. Add the MODULE_ALIAS in case they do get built as modules.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Regulators need to be available early in init in order to allow them
to be available for consumers when requested. This is generally done
by registering them at subsys_initcall() time but not all regulator
drivers have done that. Convert these drivers to do so in order to
mimimise future support.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch fixes the follwing build failure on powerpc:-

> Today's linux-next build (powerpc allyesconfig) failed like this:
>
> drivers/regulator/userspace-consumer.c:43: error: conflicting types
> for 'show_state'
> include/linux/sched.h:273: note: previous definition of 'show_state'
> was here
>
> Caused by commit 5defa2bce704ca4151cfe24e4297aa7797cafd22 ("regulator:
> add userspace-consumer driver") which I have reverted for today.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.

The chip is controlled through the I2C bus.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/scsi/fcoe/fcoe.c
	net/core/drop_monitor.c
	net/core/net-traces.c

Let's use TICKS instead of US, so PSCHED_TICKS2NS and PSCHED_NS2TICKS
(like in PSCHED_TICKS_PER_SEC already) to avoid misleading.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While doing trie_rebalance(): resize(), inflate(), halve() RCU free
tnodes before updating their parents. It depends on RCU delaying the
real destruction, but if RCU readers start after call_rcu() and before
parent update they could access freed memory.

It is currently prevented with preempt_disable() on the update side,
but it's not safe, except maybe classic RCU, plus it conflicts with
memory allocations with GFP_KERNEL flag used from these functions.

This patch explicitly delays freeing of tnodes by adding them to the
list, which is flushed after the update is finished.
Reported-by: NYan Zheng <zheng.yan@oracle.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On systems where CONFIG_SHMEM is disabled, mounting tmpfs filesystems can
fail when tmpfs options are used.  This is because tmpfs creates a small
wrapper around ramfs which rejects unknown options, and ramfs itself only
supports a tiny subset of what tmpfs supports.  This makes it pretty hard
to use the same userspace systems across different configuration systems.
As such, ramfs should ignore the tmpfs options when tmpfs is merely a
wrapper around ramfs.

This used to work before commit c3b1b1cb as previously, ramfs would
ignore all options.  But now, we get:
ramfs: bad mount option: size=10M
mount: mounting mdev on /dev failed: Invalid argument

Another option might be to restore the previous behavior, where ramfs
simply ignored all unknown mount options ... which is what Hugh prefers.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: NMatt Mackall <mpm@selenic.com>
Acked-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>