If the ucb1x00 touchscreen is resumed while the touchscreen is being
touched, the main thread stops responding.  This occurs because two
things happen:

1. When we suspended, we were woken up, and executed the loop.
   Finding that the touchscreen was not pressed, we prepare to
   schedule for a maximum timeout, before being stopped in
   try_to_freeze().

2. an irq occurs, we disable the irq, and mark it as disabled,
   and wake the thread.  This wake occurs while the thread is
   still within __refrigerator()

3. The thread is unfrozen, and __refrigerator() sets the threads
   state back to INTERRUPTIBLE.

We then drop into schedule_timeout() with an infinite timeout and the
IRQ disabled.  This prevents any further screen touches activating
the thread.

Fix this by using kthread_freezable_should_stop() which handles the
freezing issues for us outside of the hotspot where the task state
matters.  Include a flag to ignore the touchscreen until it is
released to avoid sending unintended data to the application.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

gpiolib drivers should first set the output data before setting the
direction to avoid putting glitches on an output signal.  As an
additional bonus, we tweak the code to avoid unnecessary register
writes to the output and direction registers if they have no need
to be updated.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We were not restoring the UCB1x00 gpio output data on resume, resulting
in incorrect GPIO output data after a resume.  Add the missing register
write.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The genirq layer complains if an interrupt handler returns with
interrupts enabled.  The UCB1x00 handler does just this, because
ucb1x00_enable() calls mcp_enable(), which uses spin_lock_irq()
rather than spin_lock_irqsave().  Convert this, and the divisor
setting functions to use spin_lock_irqsave().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 5dd7bf59.

Conflicts:

	scripts/mod/file2alias.c

This change is wrong on many levels.  First and foremost, it causes a
regression.  On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:

	ucb1x00 ID not found: 1005

0x1005 is a valid ID for the UCB1300 device.

Secondly, this patch is way over the top in terms of complexity.  The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver.  Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.

This reverts commit af9081ae.

This revert is necessary to revert 5dd7bf59.

This patch fixes an (ACPI S3) suspend regression introduced in commit
68d6e671 ("tpm: Introduce function to poll for result of self test")
and occurring with an Infineon TPM and tpm_tis and tpm_infineon drivers
active.

The suspend problem occurred if the TPM was disabled and/or deactivated
and therefore the TPM_PCRRead checking the result of the (asynchronous)
self test returned an error code which then caused the tpm_tis driver to
become inactive and this then seemed to have negatively influenced the
suspend support by the tpm_infineon driver...  Besides that the tpm_tis
drive may stay active even if the TPM is disabled and/or deactivated.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The type of 'make_request_fn' changed in 5a7bbad2 ("block: remove
support for bio remapping from ->make_request"), but the merge of the
nvme driver didn't take that into account, and as a result the driver
would compile with a warning:

  drivers/block/nvme.c: In function 'nvme_alloc_ns':
  drivers/block/nvme.c:1336:2: warning: passing argument 2 of 'blk_queue_make_request' from incompatible pointer type [enabled by default]
  include/linux/blkdev.h:830:13: note: expected 'void (*)(struct request_queue *, struct bio *)' but argument is of type 'int (*)(struct request_queue *, struct bio *)'

It's benign, but the warning is annoying.
Reported-by: NStephen Rothwell <sfr@canb.auug.org>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix these warnings:

  drivers/xen/biomerge.c:14:1: warning: data definition has no type or storage class [enabled by default]
  drivers/xen/biomerge.c:14:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
  drivers/xen/biomerge.c:14:1: warning: parameter names (without types) in function declaration [enabled by default]

And this build error:

  ERROR: "xen_biovec_phys_mergeable" [drivers/block/nvme.ko] undefined!
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using the correct gpio offset for setting the initial value
of gpio when setting output direction.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

ACPI 5.0 provides extensions to the EINJ mechanism to specify the
target for the error injection - by APICID for cpu related errors,
by address for memory related errors, and by segment/bus/device/function
for PCIe related errors. Also extensions for vendor specific error
injections.
Tested-by: NChen Gong <gong.chen@linux.intel.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Function split up, should have no functional change.

Provides entry point for physically hotplugged CPUs
to initialize and activate cpuidle.
Signed-off-by: NThomas Renninger <trenn@suse.de>
CC: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
CC: Shaohua Li <shaohua.li@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

V2: Fix typo: pr->handle -> pr, here: acpi_processor_hotadd_init(pr)

This is a very small part taken from patches which afaik
are coming from Yunhong Jiang (for a Xen not a Linus repo?).

Cleanup only: no functional change.

Advantage (beside cleanup) is that other data of the pr (acpi_processor) struct
in the acpi_processor_hotadd_init() is needed later, for example a newly
introduced flag:
pr->flags.need_hotplug_init
Signed-off-by: NThomas Renninger <trenn@suse.de>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Jiang, Yunhong <yunhong.jiang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled.  However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup.  When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.

This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt.  In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

due to broken suspend functionality.
Signed-off-by: NBenjamin Larsson <benjamin@southpole.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

BF54x on-chip ATAPI controller allows maximum 0x1fffe bytes to be transfered
in one ATAPI transfer. So, set the max sg_tablesize to 4.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: NYutaka Ando <r46913@freescale.com>
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This saves devices suspend/resume time.

Tested system suspend/resume with SATA IDE/AHCI mode 3 times.
Below is the time took for devices suspend/resume.

SATA mode    vanilla-kernel           patched-kernel
---------    ---------------------    ---------------------
IDE          suspend: 0.744           suspend: 0.432
             (0.716, 0.768, 0.748)    (0.440, 0.428, 0.428)

             resume: 5.084            resume: 2.209
             (5.100, 5.064, 5.088)    (2.168, 2.232, 2.228)

AHCI:        suspend: 0.725           suspend: 0.449
             (0.740, 0.708, 0.728)    (0.456, 0.448, 0.444)

             resume: 2.556            resume: 1.896
             (2.604, 2.492, 2.572)    (1.932, 1.872, 1.884)
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The as3645a driver calls kzalloc(). Include slab.h.
Reported-by: NFredrik Lingvall <fredrik.lingvall@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The intent here was to test if the FE_HAS_LOCK was set.  The current
test is equivalent to "if (status) { ..."
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Several control names used inconsistent capitalization or were inconsistent
in other ways. I also corrected a spelling mistake and fixed four strings
that were too long (>31 characters). Harmless, but the string is cut off when
it is returned with QUERYCTRL.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add an override of read_status to intercept lock status. This allows
us to switch LEDs appropriately on and off with signal un/locked.

The second phase is to override sleep to properly turn off both.

This is a hackish way to achieve that.

Thanks to Mike Krufky for his help.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This means cut & paste from the former f. attach. But while at it write
to the right GPIO to turn on the right LED. Also turn the other two
off jsut for sure.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The start is common for both stk7070pd and novatd specific routine.
This is just a preparation for the next patch.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

To properly support the three LEDs which are on the stick, we need
a special handling in the ->frontend_attach function. Thus let's have
a separate ->frontend_attach instead of ifs in the common one.

The hadnling itself will be added in further patches.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The dib0700 needs a binary firmware file. This patch added the MODULE_FIRMWARE-macro.
Signed-off-by: NChristoph Anton Mitterer <calestyo@scientia.net>
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This small patch removes superfluous DTV_CMDs from dvb_frontend.c which were added in the initially when ISBD-T support was added.
They were there unnoticed even though compilers should have warning about those duplicates. Finally they did and now we can remove them.

Thanks to Dan Carpenter <dan.carpenter@oracle.com> for pointing that out.
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

queue_setup callback has been extended with struct v4l2_format *fmt
parameter in 2d86401c commit. This patch adds this parameter to
s5p-jpeg driver.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rewrite a duplicated test to test the correct value

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E;
@@

(
* E
  || ... || E
|
* E
  && ... && E
)
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rewrite a duplicated test to test the correct value

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E;
@@

(
* E
  || ... || E
|
* E
  && ... && E
)
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the mismatch between control IDs (CID) and controls
for hflip, vflip and rotate.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver does an unconditional read of io space during module init which
causes a bad dereference on ARM.  It looks to me like this is an x86 only
drivers, so restrict it to only compile on x86.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Denis Turischev <denis@compulab.co.il>

On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

ML7831 is companion chip for Intel Atom E6xx series.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch modified the setting value of
I2C Bus Transfer Rate Setting Counter regisrer.
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>