This patch adds DT support for the Seagate Personal Cloud 1 and 2-Bay.

Here are some information allowing to identify these devices:

Product name                 | Personal Cloud | Personal Cloud 2-Bay
Code name (board/PCB)        | Cumulus        | Cumulus Max
Model name (case sticker)    | SRN21C         | SRN22C
Material desc (product spec) | STCRxxxxxxx    | STCSxxxxxxx

Chipset list:
- SoC Marvell Armada 370 88F6707, CPU @1GHz
- SDRAM memory: 512MB DDR3 667MHz (16-bits bandwidth)
- SPI flash 1MB (Macronix MX25L8006E)
- 1 or 2 SATA internal ports
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- 1 USB3 host port (PCIe controller ASM1042)
- 1 USB2 host port (SoC)
- 2 push buttons (power and reset)
- 1 SATA LED (bi-color, white and red)

Note that support for the white SATA LED is missing. A dedicated LED
driver is needed.
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This patch adds DT support for the Seagate NAS 2 and 4-Bay.

Here are some information allowing to identify these devices:

Product name                 | Seagate NAS 2-Bay | Seagate NAS 4-Bay
Code name (board/PCB)        | Dart 2-Bay        | Dart 4-Bay
Model name (case sticker)    | SRPD20            | SRPD40
Material desc (product spec) | STCTxxxxxxx       | STCUxxxxxxx

Chipset list (common):
- SoC Marvell Armada 370 88F6707, CPU @1.2GHz
- SDRAM memory: 512MB DDR3 600MHz (16-bits bandwidth)
- NAND flash 256MB, 8-bits (Micron MT29F2G08AAB or Hinyx H27U2G8F2CTR-BC)
- 2 SATA II ports (SoC)
- 1 Ethernet Gigabit ports (PHY Marvell 88E1518)
- 2 USB3 host ports (PCIe controller ASM1042)
- GPIO fan (4 speeds)
- External I2C RTC (MCP7940NT)
- 3 push buttons (power, backup and reset)
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)

Only on 4-Bay models:
- 2 extra SATA III ports (PCIe AHCI controller Marvell 88SE9170)
- 1 extra Ethernet Gigabit ports (PHY Marvell 88E1518)
- I2C GPIO expander (PCA9554A)
- 2 extra SATA LEDs (bi-color, blue and red)

Note that support for the white SATA LEDs associated with HDDs 0 and 1
is missing. A dedicated LED driver is needed.
Signed-off-by: NVincent Donnefort <vdonnefort@gmail.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Explicitly use the SoC specific compatible strings in kirkwood.dtsi and
dove.dtsi, so that the crypto devices have access to the TDMA feature
when attached to the new CESA driver.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The new bindings split the crypto and sram node in two separate devices.
Modify the existing crypto nodes to match the new representation.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add crypto related nodes in armada-38x.dtsi.

[gregory.clement@free-electrons.com: Fix typo for compatible string
armada38x instead of armada375]
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add crypto related nodes in armada-375.dtsi.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add crypto related nodes in armada-370.dtsi.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add crypto related nodes to armada-xp.dtsi.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This commit adds the description of the CPU config registers in the
Armada 370 and Armada XP Device Tree. Since the registers are in fact
different between the two SoCs, a different compatible string is used.

Note that the Armada 370 node is currently unused, but it is
nonetheless added for consistency with the addition on the Armada XP
side.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Use stdout-path so that we don't have to put the console on the
kernel command line.

Cc: Tim Bird <tim.bird@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.

Cc: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.

Cc: Mike Rapoport <mike.rapoport@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Add a label to the serial nodes that are being used for the
console.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SOC specific and the external
clock is board dependent. Adding the corresponding nodes.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Since the LED modes mapping is no longer hardcoded inside the leds-ns2
driver, then it must be provided through the modes-map property in the
ns2-leds nodes.
Signed-off-by: NVincent Donnefort <vdonnefort@gmail.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>

The base addresses for the Ux500 PRCC controllers are hardcoded,
let's move them to the clock node in the device tree and delete
the constants.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NMichael Turquette <mturquette@baylibre.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Specify how the GPIOs map to the pins in Tegra SoCs, so the dependency is
explicit.
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Current base address is wrong by 0x04 bytes for AHB bus device as shown
in dmesg:

	tegra-ahb 6000c004.ahb: incorrect AHB base address in DT data - enabling workaround

To correct old DTBs, commit ce7a10b0 ("ARM: 8334/1: amba: tegra-ahb:
detect and correct bogus base address") checks for the low bit of the
base address and removes theses 0x04 bytes at runtime.

This patch fixes the original DTS, so upstream version doesn't need the
workaround of the base address.

As both addresses are valid, this patch doesn't break compatibility.

Tested on tegra20-paz00 (aka ac100).
Signed-off-by: NNicolas Chauvet <kwizart@gmail.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This patch modifies the device tree for Tegra124 based devices to enable
the Cortex A15 PMU. The interrupt numbers are taken from NVIDIA Tegra K1
TRM (DP-06905-001_v03p). This patch was tested on a Jetson TK1.
Signed-off-by: NKyle Huey <khuey@kylehuey.com>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the device-tree node for the GK20A GPU and leave it disabled.
It is the responsibility of the bootloader to enable it if the
VPR registers have been programmed such that the GPU can operate.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the device-tree node for the GK20A GPU and leave it disabled.
It is the responsibility of the bootloader to enable it if the
VPR registers have been programmed such that the GPU can operate.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>

Nouveau can make use of the IOMMU to make physical appear linear in the
GPU address space.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Specify the CPU voltage regulator for the cpufreq driver.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The Tegra124 cpufreq driver relies on certain clocks being present
in the /cpus/cpu@0 node.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the board-specific properties of the DFLL for the Jetson TK1 board.
On this board, the DFLL will take control of the sd0 regulator on the
on-board AS3722 PMIC.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The DFLL clocksource is a separate IP block from the usual
clock-and-reset controller, so it gets its own device tree node.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Signed-off-by: NMoritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This SoC is integrated with 4 Cortex-A9 cores.  The GIC bindings
document says that the bits[15:8] of the 3rd cell of the interrupts
property represents PPI interrupt CPU mask.  Because the timer
interrupts are wired to all of the 4 cores, bits[15:8] should be set
to 0xf.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

When getting translated from a downstream device tree that used slightly
different DT bindings, these regulators got labeled with the
"on-in-suspend" state, when they were actually supposed to be turned off
for S3 suspend. This was harmless, but not intentional, AFAICT.

Let's turn them off to get the optimal power state.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This DTS file was submitted with non-upstream bindings. I happened
across this while reviewing the jaq DTS.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>