== The problem ==

There are use-cases when a program of some type can be attached to
multiple attach points and those attach points must have different
permissions to access context or to call helpers.

E.g. context structure may have fields for both IPv4 and IPv6 but it
doesn't make sense to read from / write to IPv6 field when attach point
is somewhere in IPv4 stack.

Same applies to BPF-helpers: it may make sense to call some helper from
some attach point, but not from other for same prog type.

== The solution ==

Introduce `expected_attach_type` field in in `struct bpf_attr` for
`BPF_PROG_LOAD` command. If scenario described in "The problem" section
is the case for some prog type, the field will be checked twice:

1) At load time prog type is checked to see if attach type for it must
   be known to validate program permissions correctly. Prog will be
   rejected with EINVAL if it's the case and `expected_attach_type` is
   not specified or has invalid value.

2) At attach time `attach_type` is compared with `expected_attach_type`,
   if prog type requires to have one, and, if they differ, attach will
   be rejected with EINVAL.

The `expected_attach_type` is now available as part of `struct bpf_prog`
in both `bpf_verifier_ops->is_valid_access()` and
`bpf_verifier_ops->get_func_proto()` () and can be used to check context
accesses and calls to helpers correspondingly.

Initially the idea was discussed by Alexei Starovoitov <ast@fb.com> and
Daniel Borkmann <daniel@iogearbox.net> here:
https://marc.info/?l=linux-netdev&m=152107378717201&w=2Signed-off-by: NAndrey Ignatov <rdna@fb.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

This implements a BPF ULP layer to allow policy enforcement and
monitoring at the socket layer. In order to support this a new
program type BPF_PROG_TYPE_SK_MSG is used to run the policy at
the sendmsg/sendpage hook. To attach the policy to sockets a
sockmap is used with a new program attach type BPF_SK_MSG_VERDICT.

Similar to previous sockmap usages when a sock is added to a
sockmap, via a map update, if the map contains a BPF_SK_MSG_VERDICT
program type attached then the BPF ULP layer is created on the
socket and the attached BPF_PROG_TYPE_SK_MSG program is run for
every msg in sendmsg case and page/offset in sendpage case.

BPF_PROG_TYPE_SK_MSG Semantics/API:

BPF_PROG_TYPE_SK_MSG supports only two return codes SK_PASS and
SK_DROP. Returning SK_DROP free's the copied data in the sendmsg
case and in the sendpage case leaves the data untouched. Both cases
return -EACESS to the user. Returning SK_PASS will allow the msg to
be sent.

In the sendmsg case data is copied into kernel space buffers before
running the BPF program. The kernel space buffers are stored in a
scatterlist object where each element is a kernel memory buffer.
Some effort is made to coalesce data from the sendmsg call here.
For example a sendmsg call with many one byte iov entries will
likely be pushed into a single entry. The BPF program is run with
data pointers (start/end) pointing to the first sg element.

In the sendpage case data is not copied. We opt not to copy the
data by default here, because the BPF infrastructure does not
know what bytes will be needed nor when they will be needed. So
copying all bytes may be wasteful. Because of this the initial
start/end data pointers are (0,0). Meaning no data can be read or
written. This avoids reading data that may be modified by the
user. A new helper is added later in this series if reading and
writing the data is needed. The helper call will do a copy by
default so that the page is exclusively owned by the BPF call.

The verdict from the BPF_PROG_TYPE_SK_MSG applies to the entire msg
in the sendmsg() case and the entire page/offset in the sendpage case.
This avoids ambiguity on how to handle mixed return codes in the
sendmsg case. Again a helper is added later in the series if
a verdict needs to apply to multiple system calls and/or only
a subpart of the currently being processed message.

The helper msg_redirect_map() can be used to select the socket to
send the data on. This is used similar to existing redirect use
cases. This allows policy to redirect msgs.

Pseudo code simple example:

The basic logic to attach a program to a socket is as follows,

  // load the programs
  bpf_prog_load(SOCKMAP_TCP_MSG_PROG, BPF_PROG_TYPE_SK_MSG,
		&obj, &msg_prog);

  // lookup the sockmap
  bpf_map_msg = bpf_object__find_map_by_name(obj, "my_sock_map");

  // get fd for sockmap
  map_fd_msg = bpf_map__fd(bpf_map_msg);

  // attach program to sockmap
  bpf_prog_attach(msg_prog, map_fd_msg, BPF_SK_MSG_VERDICT, 0);

Adding sockets to the map is done in the normal way,

  // Add a socket 'fd' to sockmap at location 'i'
  bpf_map_update_elem(map_fd_msg, &i, fd, BPF_ANY);

After the above any socket attached to "my_sock_map", in this case
'fd', will run the BPF msg verdict program (msg_prog) on every
sendmsg and sendpage system call.

For a complete example see BPF selftests or sockmap samples.

Implementation notes:

It seemed the simplest, to me at least, to use a refcnt to ensure
psock is not lost across the sendmsg copy into the sg, the bpf program
running on the data in sg_data, and the final pass to the TCP stack.
Some performance testing may show a better method to do this and avoid
the refcnt cost, but for now use the simpler method.

Another item that will come after basic support is in place is
supporting MSG_MORE flag. At the moment we call sendpages even if
the MSG_MORE flag is set. An enhancement would be to collect the
pages into a larger scatterlist and pass down the stack. Notice that
bpf_tcp_sendmsg() could support this with some additional state saved
across sendmsg calls. I built the code to support this without having
to do refactoring work. Other features TBD include ZEROCOPY and the
TCP_RECV_QUEUE/TCP_NO_QUEUE support. This will follow initial series
shortly.

Future work could improve size limits on the scatterlist rings used
here. Currently, we use MAX_SKB_FRAGS simply because this was being
used already in the TLS case. Future work could extend the kernel sk
APIs to tune this depending on workload. This is a trade-off
between memory usage and throughput performance.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Tell user space about device on which the map was created.
Unfortunate reality of user ABI makes sharing this code
with program offload difficult but the information is the
same.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

For host JIT, there are "jited_len"/"bpf_func" fields in struct bpf_prog
used by all host JIT targets to get jited image and it's length. While for
offload, targets are likely to have different offload mechanisms that these
info are kept in device private data fields.

Therefore, BPF_OBJ_GET_INFO_BY_FD syscall needs an unified way to get JIT
length and contents info for offload targets.

One way is to introduce new callback to parse device private data then fill
those fields in bpf_prog_info. This might be a little heavy, the other way
is to add generic fields which will be initialized by all offload targets.

This patch follow the second approach to introduce two new fields in
struct bpf_dev_offload and teach bpf_prog_get_info_by_fd about them to fill
correct jited_prog_len and jited_prog_insns in bpf_prog_info.
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NJiong Wang <jiong.wang@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

BPF map offload follow similar path to program offload.  At creation
time users may specify ifindex of the device on which they want to
create the map.  Map will be validated by the kernel's
.map_alloc_check callback and device driver will be called for the
actual allocation.  Map will have an empty set of operations
associated with it (save for alloc and free callbacks).  The real
device callbacks are kept in map->offload->dev_ops because they
have slightly different signatures.  Map operations are called in
process context so the driver may communicate with HW freely,
msleep(), wait() etc.

Map alloc and free callbacks are muxed via existing .ndo_bpf, and
are always called with rtnl lock held.  Maps and programs are
guaranteed to be destroyed before .ndo_uninit (i.e. before
unregister_netdev() returns).  Map callbacks are invoked with
bpf_devs_lock *read* locked, drivers must take care of exclusive
locking if necessary.

All offload-specific branches are marked with unlikely() (through
bpf_map_is_dev_bound()), given that branch penalty will be
negligible compared to IO anyway, and we don't want to penalize
SW path unnecessarily.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

With map offload coming, we need to call program offload structure
something less ambiguous.  Pure rename, no functional changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

All map types reimplement the field-by-field copy of union bpf_attr
members into struct bpf_map.  Add a helper to perform this operation.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

.map_alloc callbacks contain a number of checks validating user-
-provided map attributes against constraints of a particular map
type.  For offloaded maps we will need to check map attributes
without actually allocating any memory on the host.  Add a new
callback for validating attributes before any memory is allocated.
This callback can be selectively implemented by map types for
sharing code with offloads, or simply to separate the logical
steps of validation and allocation.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Since error-injection framework is not limited to be used
by kprobes, nor bpf. Other kernel subsystems can use it
freely for checking safeness of error-injection, e.g.
livepatch, ftrace etc.
So this separate error-injection framework from kprobes.

Some differences has been made:

- "kprobe" word is removed from any APIs/structures.
- BPF_ALLOW_ERROR_INJECTION() is renamed to
  ALLOW_ERROR_INJECTION() since it is not limited for BPF too.
- CONFIG_FUNCTION_ERROR_INJECTION is the config item of this
  feature. It is automatically enabled if the arch supports
  error injection feature for kprobe or ftrace etc.
Signed-off-by: NMasami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: NJosef Bacik <jbacik@fb.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

In addition to commit b2157399 ("bpf: prevent out-of-bounds
speculation") also change the layout of struct bpf_map such that
false sharing of fast-path members like max_entries is avoided
when the maps reference counter is altered. Therefore enforce
them to be placed into separate cachelines.

pahole dump after change:

  struct bpf_map {
        const struct bpf_map_ops  * ops;                 /*     0     8 */
        struct bpf_map *           inner_map_meta;       /*     8     8 */
        void *                     security;             /*    16     8 */
        enum bpf_map_type          map_type;             /*    24     4 */
        u32                        key_size;             /*    28     4 */
        u32                        value_size;           /*    32     4 */
        u32                        max_entries;          /*    36     4 */
        u32                        map_flags;            /*    40     4 */
        u32                        pages;                /*    44     4 */
        u32                        id;                   /*    48     4 */
        int                        numa_node;            /*    52     4 */
        bool                       unpriv_array;         /*    56     1 */

        /* XXX 7 bytes hole, try to pack */

        /* --- cacheline 1 boundary (64 bytes) --- */
        struct user_struct *       user;                 /*    64     8 */
        atomic_t                   refcnt;               /*    72     4 */
        atomic_t                   usercnt;              /*    76     4 */
        struct work_struct         work;                 /*    80    32 */
        char                       name[16];             /*   112    16 */
        /* --- cacheline 2 boundary (128 bytes) --- */

        /* size: 128, cachelines: 2, members: 17 */
        /* sum members: 121, holes: 1, sum holes: 7 */
  };

Now all entries in the first cacheline are read only throughout
the life time of the map, set up once during map creation. Overall
struct size and number of cachelines doesn't change from the
reordering. struct bpf_map is usually first member and embedded
in map structs in specific map implementations, so also avoid those
members to sit at the end where it could potentially share the
cacheline with first map values e.g. in the array since remote
CPUs could trigger map updates just as well for those (easily
dirtying members like max_entries intentionally as well) while
having subsequent values in cache.

Quoting from Google's Project Zero blog [1]:

  Additionally, at least on the Intel machine on which this was
  tested, bouncing modified cache lines between cores is slow,
  apparently because the MESI protocol is used for cache coherence
  [8]. Changing the reference counter of an eBPF array on one
  physical CPU core causes the cache line containing the reference
  counter to be bounced over to that CPU core, making reads of the
  reference counter on all other CPU cores slow until the changed
  reference counter has been written back to memory. Because the
  length and the reference counter of an eBPF array are stored in
  the same cache line, this also means that changing the reference
  counter on one physical CPU core causes reads of the eBPF array's
  length to be slow on other physical CPU cores (intentional false
  sharing).

While this doesn't 'control' the out-of-bounds speculation through
masking the index as in commit b2157399, triggering a manipulation
of the map's reference counter is really trivial, so lets not allow
to easily affect max_entries from it.

Splitting to separate cachelines also generally makes sense from
a performance perspective anyway in that fast-path won't have a
cache miss if the map gets pinned, reused in other progs, etc out
of control path, thus also avoids unintentional false sharing.

  [1] https://googleprojectzero.blogspot.ch/2018/01/reading-privileged-memory-with-side.htmlSigned-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Under speculation, CPUs may mis-predict branches in bounds checks. Thus,
memory accesses under a bounds check may be speculated even if the
bounds check fails, providing a primitive for building a side channel.

To avoid leaking kernel data round up array-based maps and mask the index
after bounds check, so speculated load with out of bounds index will load
either valid value from the array or zero from the padded area.

Unconditionally mask index for all array types even when max_entries
are not rounded to power of 2 for root user.
When map is created by unpriv user generate a sequence of bpf insns
that includes AND operation to make sure that JITed code includes
the same 'index & index_mask' operation.

If prog_array map is created by unpriv user replace
  bpf_tail_call(ctx, map, index);
with
  if (index >= max_entries) {
    index &= map->index_mask;
    bpf_tail_call(ctx, map, index);
  }
(along with roundup to power 2) to prevent out-of-bounds speculation.
There is secondary redundant 'if (index >= max_entries)' in the interpreter
and in all JITs, but they can be optimized later if necessary.

Other array-like maps (cpumap, devmap, sockmap, perf_event_array, cgroup_array)
cannot be used by unpriv, so no changes there.

That fixes bpf side of "Variant 1: bounds check bypass (CVE-2017-5753)" on
all architectures with and without JIT.

v2->v3:
Daniel noticed that attack potentially can be crafted via syscall commands
without loading the program, so add masking to those paths as well.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Descriptor table is a shared object; it's not a place where you can
stick temporary references to files, especially when we don't need
an opened file at all.

Cc: stable@vger.kernel.org # v4.14
Fixes: 98589a09 ("netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'")
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The sockmap infrastructure is only aware of TCP sockets at the
moment. In the future we plan to add UDP. In both cases CONFIG_NET
should be built-in.

So lets only build sockmap if CONFIG_INET is enabled.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Report to the user ifindex and namespace information of offloaded
programs.  If device has disappeared return -ENODEV.  Specify the
namespace using dev/inode combination.

CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Bound programs are quite useless after their device disappears.
They are simply waiting for reference count to go to zero,
don't list them in BPF_PROG_GET_NEXT_ID by freeing their ID
early.

Note that orphaned offload programs will return -ENODEV on
BPF_OBJ_GET_INFO_BY_FD so user will never see ID 0.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

To allow verifier instruction callbacks without any extra locking
NETDEV_UNREGISTER notification would wait on a waitqueue for verifier
to finish.  This design decision was made when rtnl lock was providing
all the locking.  Use the read/write lock instead and remove the
workqueue.

Verifier will now call into the offload code, so dev_ops are moved
to offload structure.  Since verifier calls are all under
bpf_prog_is_dev_bound() we no longer need static inline implementations
to please builds with CONFIG_NET=n.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

We currently use aux->offload to indicate that program is bound
to a specific device.  This forces us to keep the offload structure
around even after the device is gone.  Add a bool member to
struct bpf_prog_aux to indicate if offload was requested.
Suggested-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Typical JIT does several passes over bpf instructions to
compute total size and relative offsets of jumps and calls.
With multitple bpf functions calling each other all relative calls
will have invalid offsets intially therefore we need to additional
last pass over the program to emit calls with correct offsets.
For example in case of three bpf functions:
main:
  call foo
  call bpf_map_lookup
  exit
foo:
  call bar
  exit
bar:
  exit

We will call bpf_int_jit_compile() indepedently for main(), foo() and bar()
x64 JIT typically does 4-5 passes to converge.
After these initial passes the image for these 3 functions
will be good except call targets, since start addresses of
foo() and bar() are unknown when we were JITing main()
(note that call bpf_map_lookup will be resolved properly
during initial passes).
Once start addresses of 3 functions are known we patch
call_insn->imm to point to right functions and call
bpf_int_jit_compile() again which needs only one pass.
Additional safety checks are done to make sure this
last pass doesn't produce image that is larger or smaller
than previous pass.

When constant blinding is on it's applied to all functions
at the first pass, since doing it once again at the last
pass can change size of the JITed code.

Tested on x64 and arm64 hw with JIT on/off, blinding on/off.
x64 jits bpf-to-bpf calls correctly while arm64 falls back to interpreter.
All other JITs that support normal BPF_CALL will behave the same way
since bpf-to-bpf call is equivalent to bpf-to-kernel call from
JITs point of view.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

though bpf_call is still the same call instruction and
calling convention 'bpf to bpf' and 'bpf to helper' is the same
the interpreter has to oparate on 'struct bpf_insn *'.
To distinguish these two cases add a kernel internal opcode and
mark call insns with it.
This opcode is seen by interpreter only. JITs will never see it.
Also add tiny bit of debug code to aid interpreter debugging.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Commit f371b304 ("bpf/tracing: allow user space to
query prog array on the same tp") introduced a perf
ioctl command to query prog array attached to the
same perf tracepoint. The commit introduced a
compilation error under certain config conditions, e.g.,
  (1). CONFIG_BPF_SYSCALL is not defined, or
  (2). CONFIG_TRACING is defined but neither CONFIG_UPROBE_EVENTS
       nor CONFIG_KPROBE_EVENTS is defined.

Error message:
  kernel/events/core.o: In function `perf_ioctl':
  core.c:(.text+0x98c4): undefined reference to `bpf_event_query_prog_array'

This patch fixed this error by guarding the real definition under
CONFIG_BPF_EVENTS and provided static inline dummy function
if CONFIG_BPF_EVENTS was not defined.
It renamed the function from bpf_event_query_prog_array to
perf_event_query_prog_array and moved the definition from linux/bpf.h
to linux/trace_events.h so the definition is in proximity to
other prog_array related functions.

Fixes: f371b304 ("bpf/tracing: allow user space to query prog array on the same tp")
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Using BPF we can override kprob'ed functions and return arbitrary
values.  Obviously this can be a bit unsafe, so make this feature opt-in
for functions.  Simply tag a function with KPROBE_ERROR_INJECT_SYMBOL in
order to give BPF access to that function for error injection purposes.
Signed-off-by: NJosef Bacik <jbacik@fb.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Commit e87c6bc3 ("bpf: permit multiple bpf attachments
for a single perf event") added support to attach multiple
bpf programs to a single perf event.
Although this provides flexibility, users may want to know
what other bpf programs attached to the same tp interface.
Besides getting visibility for the underlying bpf system,
such information may also help consolidate multiple bpf programs,
understand potential performance issues due to a large array,
and debug (e.g., one bpf program which overwrites return code
may impact subsequent program results).

Commit 2541517c ("tracing, perf: Implement BPF programs
attached to kprobes") utilized the existing perf ioctl
interface and added the command PERF_EVENT_IOC_SET_BPF
to attach a bpf program to a tracepoint. This patch adds a new
ioctl command, given a perf event fd, to query the bpf program
array attached to the same perf tracepoint event.

The new uapi ioctl command:
  PERF_EVENT_IOC_QUERY_BPF

The new uapi/linux/perf_event.h structure:
  struct perf_event_query_bpf {
       __u32	ids_len;
       __u32	prog_cnt;
       __u32	ids[0];
  };

User space provides buffer "ids" for kernel to copy to.
When returning from the kernel, the number of available
programs in the array is set in "prog_cnt".

The usage:
  struct perf_event_query_bpf *query =
    malloc(sizeof(*query) + sizeof(u32) * ids_len);
  query.ids_len = ids_len;
  err = ioctl(pmu_efd, PERF_EVENT_IOC_QUERY_BPF, query);
  if (err == 0) {
    /* query.prog_cnt is the number of available progs,
     * number of progs in ids: (ids_len == 0) ? 0 : query.prog_cnt
     */
  } else if (errno == ENOSPC) {
    /* query.ids_len number of progs copied,
     * query.prog_cnt is the number of available progs
     */
  } else {
      /* other errors */
  }
Signed-off-by: NYonghong Song <yhs@fb.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

With the current ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM semantics, an helper
argument can be NULL when the next argument type is ARG_CONST_SIZE_OR_ZERO
and the verifier can prove the value of this next argument is 0. However,
most helpers are just interested in handling <!NULL, 0>, so forcing them to
deal with <NULL, 0> makes the implementation of those helpers more
complicated for no apparent benefits, requiring them to explicitly handle
those corner cases with checks that bpf programs could start relying upon,
preventing the possibility of removing them later.

Solve this by making ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM never accept NULL
even when ARG_CONST_SIZE_OR_ZERO is set, and introduce a new argument type
ARG_PTR_TO_MEM_OR_NULL to explicitly deal with the NULL case.

Currently, the only helper that needs this is bpf_csum_diff_proto(), so
change arg1 and arg3 to this new type as well.

Also add a new battery of tests that explicitly test the
!ARG_PTR_TO_MEM_OR_NULL combination: all the current ones testing the
various <NULL, 0> variations are focused on bpf_csum_diff, so cover also
other helpers.
Signed-off-by: NGianluca Borello <g.borello@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

This reverts commit bd601b6a ("bpf: report offload info to user
space").  The ifindex by itself is not sufficient, we should provide
information on which network namespace this ifindex belongs to.
After considering some options we concluded that it's best to just
remove this API for now, and rework it in -next.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

bpf_prog_get_type() is identical to bpf_prog_get_type_dev(),
with false passed as attach_drv.  Instead of keeping it as
an exported symbol turn it into static inline wrapper.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

With TC shared block changes we can't depend on correct netdev
pointer being available in cls_bpf.  Move the device validation
to the driver.  Core will only make sure that offloaded programs
are always attached in the driver (or in HW by the driver).  We
trust that drivers which implement offload callbacks will perform
necessary checks.

Moving the checks to the driver is generally a useful thing,
in practice the check should be against a switchdev instance,
not a netdev, given that most ASICs will probably allow using
the same program on many ports.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Pass the netdev pointer to bpf_prog_get_type().  This way
BPF code can decide whether the device matches what the
code was loaded/translated for.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend struct bpf_prog_info to contain information about program
being bound to a device.  Since the netdev may get destroyed while
program still exists we need a flag to indicate the program is
loaded for a device, even if the device is gone.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fact that we don't know which device the program is going
to be used on is quite limiting in current eBPF infrastructure.
We have to reverse or limit the changes which kernel makes to
the loaded bytecode if we want it to be offloaded to a networking
device.  We also have to invent new APIs for debugging and
troubleshooting support.

Make it possible to load programs for a specific netdev.  This
helps us to bring the debug information closer to the core
eBPF infrastructure (e.g. we will be able to reuse the verifer
log in device JIT).  It allows device JITs to perform translation
on the original bytecode.

__bpf_prog_get() when called to get a reference for an attachment
point will now refuse to give it if program has a device assigned.
Following patches will add a version of that function which passes
the expected netdev in. @type argument in __bpf_prog_get() is
renamed to attach_type to make it clearer that it's only set on
attachment.

All calls to ndo_bpf are protected by rtnl, only verifier callbacks
are not.  We need a wait queue to make sure netdev doesn't get
destroyed while verifier is still running and calling its driver.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit afdb09c7 ("security: bpf: Add LSM hooks for bpf object related
syscall") included linux/bpf.h in linux/security.h. As a result, bpf
programs including bpf_helpers.h and some other header that ends up
pulling in also security.h, such as several examples under samples/bpf,
fail to compile because bpf_tail_call and bpf_get_stackid are now
"redefined as different kind of symbol".

>From bpf.h:

u64 bpf_tail_call(u64 ctx, u64 r2, u64 index, u64 r4, u64 r5);
u64 bpf_get_stackid(u64 r1, u64 r2, u64 r3, u64 r4, u64 r5);

Whereas in bpf_helpers.h they are:

static void (*bpf_tail_call)(void *ctx, void *map, int index);
static int (*bpf_get_stackid)(void *ctx, void *map, int flags);

Fix this by removing the unused declaration of bpf_tail_call and moving
the declaration of bpf_get_stackid in bpf_trace.c, which is the only
place where it's needed.
Signed-off-by: NGianluca Borello <g.borello@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables multiple bpf attachments for a
kprobe/uprobe/tracepoint single trace event.
Each trace_event keeps a list of attached perf events.
When an event happens, all attached bpf programs will
be executed based on the order of attachment.

A global bpf_event_mutex lock is introduced to protect
prog_array attaching and detaching. An alternative will
be introduce a mutex lock in every trace_event_call
structure, but it takes a lot of extra memory.
So a global bpf_event_mutex lock is a good compromise.

The bpf prog detachment involves allocation of memory.
If the allocation fails, a dummy do-nothing program
will replace to-be-detached program in-place.
Signed-off-by: NYonghong Song <yhs@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a bpf object related check when sending and receiving files
through unix domain socket as well as binder. It checks if the receiving
process have privilege to read/write the bpf map or use the bpf program.
This check is necessary because the bpf maps and programs are using a
anonymous inode as their shared inode so the normal way of checking the
files and sockets when passing between processes cannot work properly on
eBPF object. This check only works when the BPF_SYSCALL is configured.
Signed-off-by: NChenbo Feng <fengc@google.com>
Acked-by: NStephen Smalley <sds@tycho.nsa.gov>
Reviewed-by: NJames Morris <james.l.morris@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce several LSM hooks for the syscalls that will allow the
userspace to access to eBPF object such as eBPF programs and eBPF maps.
The security check is aimed to enforce a per object security protection
for eBPF object so only processes with the right priviliges can
read/write to a specific map or use a specific eBPF program. Besides
that, a general security hook is added before the multiplexer of bpf
syscall to check the cmd and the attribute used for the command. The
actual security module can decide which command need to be checked and
how the cmd should be checked.
Signed-off-by: NChenbo Feng <fengc@google.com>
Acked-by: NJames Morris <james.l.morris@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce the map read/write flags to the eBPF syscalls that returns the
map fd. The flags is used to set up the file mode when construct a new
file descriptor for bpf maps. To not break the backward capability, the
f_flags is set to O_RDWR if the flag passed by syscall is 0. Otherwise
it should be O_RDONLY or O_WRONLY. When the userspace want to modify or
read the map content, it will check the file mode to see if it is
allowed to make the change.
Signed-off-by: NChenbo Feng <fengc@google.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the fact that verifier ops are now separate from program
ops to define a separate set of callbacks for verification of
already translated programs.

Since we expect the analyzer ops to be defined only for
a small subset of all program types initialize their array
by hand (don't use linux/bpf_types.h).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the verifier ops don't have to be associated with
the program for its entire lifetime we can move it to
verifier's struct bpf_verifier_env.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct bpf_verifier_ops contains both verifier ops and operations
used later during program's lifetime (test_run).  Split the runtime
ops into a different structure.

BPF_PROG_TYPE() will now append ## _prog_ops or ## _verifier_ops
to the names.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch connects cpumap to the xdp_do_redirect_map infrastructure.

Still no SKB allocation are done yet.  The XDP frames are transferred
to the other CPU, but they are simply refcnt decremented on the remote
CPU.  This served as a good benchmark for measuring the overhead of
remote refcnt decrement.  If driver page recycle cache is not
efficient then this, exposes a bottleneck in the page allocator.

A shout-out to MST's ptr_ring, which is the secret behind is being so
efficient to transfer memory pointers between CPUs, without constantly
bouncing cache-lines between CPUs.

V3: Handle !CONFIG_BPF_SYSCALL pointed out by kbuild test robot.

V4: Make Generic-XDP aware of cpumap type, but don't allow redirect yet,
 as implementation require a separate upstream discussion.

V5:
 - Fix a maybe-uninitialized pointed out by kbuild test robot.
 - Restrict bpf-prog side access to cpumap, open when use-cases appear
 - Implement cpu_map_enqueue() as a more simple void pointer enqueue

V6:
 - Allow cpumap type for usage in helper bpf_redirect_map,
   general bpf-prog side restriction moved to earlier patch.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2c16d603 ("netfilter: xt_bpf: support ebpf") introduced
support for attaching an eBPF object by an fd, with the
'bpf_mt_check_v1' ABI expecting the '.fd' to be specified upon each
IPT_SO_SET_REPLACE call.

However this breaks subsequent iptables calls:

 # iptables -A INPUT -m bpf --object-pinned /sys/fs/bpf/xxx -j ACCEPT
 # iptables -A INPUT -s 5.6.7.8 -j ACCEPT
 iptables: Invalid argument. Run `dmesg' for more information.

That's because iptables works by loading existing rules using
IPT_SO_GET_ENTRIES to userspace, then issuing IPT_SO_SET_REPLACE with
the replacement set.

However, the loaded 'xt_bpf_info_v1' has an arbitrary '.fd' number
(from the initial "iptables -m bpf" invocation) - so when 2nd invocation
occurs, userspace passes a bogus fd number, which leads to
'bpf_mt_check_v1' to fail.

One suggested solution [1] was to hack iptables userspace, to perform a
"entries fixup" immediatley after IPT_SO_GET_ENTRIES, by opening a new,
process-local fd per every 'xt_bpf_info_v1' entry seen.

However, in [2] both Pablo Neira Ayuso and Willem de Bruijn suggested to
depricate the xt_bpf_info_v1 ABI dealing with pinned ebpf objects.

This fix changes the XT_BPF_MODE_FD_PINNED behavior to ignore the given
'.fd' and instead perform an in-kernel lookup for the bpf object given
the provided '.path'.

It also defines an alias for the XT_BPF_MODE_FD_PINNED mode, named
XT_BPF_MODE_PATH_PINNED, to better reflect the fact that the user is
expected to provide the path of the pinned object.

Existing XT_BPF_MODE_FD_ELF behavior (non-pinned fd mode) is preserved.

References: [1] https://marc.info/?l=netfilter-devel&m=150564724607440&w=2
            [2] https://marc.info/?l=netfilter-devel&m=150575727129880&w=2Reported-by: NRafael Buchbinder <rafi@rbk.ms>
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Instead of u8, use char for prog and map name.  It can avoid the
userspace tool getting compiler's signess warning.  The
bpf_prog_aux, bpf_map, bpf_attr, bpf_prog_info and
bpf_map_info are changed.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>