- 21 6月, 2006 1 次提交
-
-
由 Linas Vepstas 提交于
The PCI error recovery code will printk diagnostic info when a PCI error event occurs. Change the messages to include the slot location code, which is how most sysadmins will know the device. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 19 5月, 2006 1 次提交
-
-
由 Linas Vepstas 提交于
When a PCI device driver does not support PCI error recovery, the powerpc/pseries code takes a walk through a branch of code that resets the failure counter. Because of this, if a broken PCI card is present, the kernel will attempt to reset it an infinite number of times. (This is annoying but mostly harmless: each reset takes about 10-20 seconds, and uses almost no CPU time). This patch preserves the failure count across resets. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 22 4月, 2006 1 次提交
-
-
由 Linas Vepstas 提交于
The current PCI error recovery system keeps track of the number of PCI card resets, and refuses to bring a card back up if this number is too large. The goal of doing this was to avoid an infinite loop of resets if a card is obviously dead. However, if the failures are rare, but the machine has a high uptime, this mechanism might still be triggered; this is too harsh. This patch will avoids this problem by decrementing the fail count after an hour. Thus, as long as a pci card BSOD's less than 6 times an hour, it will continue to be reset indefinitely. If it's failure rate is greater than that, it will be taken off-line permanently. This patch is larger than it might otherwise be because it changes indentation by removing a pointless while-loop. The while loop is not needed, as the handler is invoked once fo each event (by schedule_work()); the loop is leftover cruft from an earlier implementation. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 01 4月, 2006 2 次提交
-
-
由 Linas Vepstas 提交于
The recent patch to print device names in EEH reset messages was lacking ... this patch works better. Signed-off-by: NLinas Vepstas <linas@linas.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Linas Vepstas 提交于
The current code prints an ambiguous message if the recovery of a failed PCI device fails. Give this special case its own unique message. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 27 3月, 2006 1 次提交
-
-
由 Linas Vepstas 提交于
This avoids printk'ing a NULL string. Signed-off-by: NLinas Vepstas <linas@linas.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 28 2月, 2006 1 次提交
-
-
由 Olaf Hering 提交于
This patch fixes a crash in handle_eeh_events, but ethtool -t still doesnt work right. ... pepino:~ # cpu 0x3: Vector: 300 (Data Access) at [c00000005192bbe0] pc: c00000000004a380: .handle_eeh_events+0xe0/0x23c lr: c00000000004a374: .handle_eeh_events+0xd4/0x23c sp: c00000005192be60 msr: 9000000000009032 dar: 268 dsisr: 40000000 current = 0xc0000001fe7bf1a0 paca = 0xc00000000048b280 pid = 16322, comm = eehd enter ? for help [c00000005192bf00] c00000000004a808 .eeh_event_handler+0xcc/0x130 [c00000005192bf90] c000000000025e00 .kernel_thread+0x4c/0x68 ... (none):/# /usr/sbin/ethtool -i eth0 driver: e100 version: 3.5.10-k2-NAPI firmware-version: N/A bus-info: 0000:21:01.0 (none):/# /usr/sbin/ethtool -t eth0 Call Trace: [C00000000F8DEFF0] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable) [C00000000F8DF0A0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8 [C00000000F8DF150] [C000000000049E58] .eeh_check_failure+0x10c/0x138 [C00000000F8DF1E0] [C0000000002DFDB0] .e100_hw_reset+0x70/0xf4 [C00000000F8DF270] [C0000000002E1BBC] .e100_hw_init+0x2c/0x260 [C00000000F8DF310] [C0000000002E2464] .e100_loopback_test+0x8c/0x220 [C00000000F8DF3C0] [C0000000002E28DC] .e100_diag_test+0xdc/0x16c [C00000000F8DF490] [C000000000420BE0] .dev_ethtool+0xf24/0x14f8 [C00000000F8DF8F0] [C00000000041F4A8] .dev_ioctl+0x5cc/0x740 [C00000000F8DFA20] [C00000000040FEFC] .sock_ioctl+0x3d0/0x404 [C00000000F8DFAC0] [C0000000000D513C] .do_ioctl+0x68/0x108 [C00000000F8DFB50] [C0000000000D56B0] .vfs_ioctl+0x4d4/0x510 [C00000000F8DFC10] [C0000000000D5740] .sys_ioctl+0x54/0x94 [C00000000F8DFCC0] [C0000000000FB6EC] .ethtool_ioctl+0x11c/0x150 [C00000000F8DFD60] [C0000000000F7E40] .compat_sys_ioctl+0x338/0x3bc [C00000000F8DFE30] [C00000000000871C] syscall_exit+0x0/0x40 EEH: Detected PCI bus error on device 0000:21:01.0 EEH: This PCI device has failed 1 times since last reboot: <NULL> - modprobe: FATAL: Could not load /lib/modules/2.6.16-rc4-git7/modules.dep: No such file or directory Cannot get strings: No such device (none):/# (none):/# EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2 (none):/# Call Trace: [C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable) [C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8 [C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154 [C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc [C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c [C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c [C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8 [C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110 [C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250 [C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140 [C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68 EEH: Detected PCI bus error on device <NULL> EEH: This PCI device has failed 1 times since last reboot: <NULL> - EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2 Call Trace: [C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable) [C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8 [C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154 [C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc [C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c [C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c [C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8 [C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110 [C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250 [C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140 [C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68 EEH: Detected PCI bus error on device <NULL> EEH: This PCI device has failed 1 times since last reboot: <NULL> - EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2 Call Trace: [C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable) [C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8 [C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154 [C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc [C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c [C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c [C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8 [C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110 [C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250 [C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140 [C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68 EEH: Detected PCI bus error on device <NULL> and so on Signed-off-by: NOlaf Hering <olh@suse.de> Acked-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 08 2月, 2006 1 次提交
-
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
- 10 1月, 2006 5 次提交
-
-
由 Paul Mackerras 提交于
<asm/systemcfg.h> is gone now, and the PCI error recovery constants in include/linux/pci.h changed their names in the process of getting accepted. Signed-off-by: NPaul Mackerras <paulus@samba.org> (cherry picked from 5a2516156c591fc3d2059fbd93f97e15eb6010d6 commit)
-
由 Linas Vepstas 提交于
239-eeh-multifunction-consolidate.patch New-style firmware will often place multiple different functions under a non-EEH-aware parent. However, these devices might share a common PE "partition endpoint" and config address, ad thus any EEH events will affect all of the devices in common. This patch makes the effort to find all of these common devices and handle them together. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org> (cherry picked from 216810296bb97d39da8e176822e9de78d2f00187 commit)
-
由 Linas Vepstas 提交于
238-eeh-stop-if-reset_failed.patch If the firmware is unable to reset the PCI slot for some reason, then don't attempt any further recovery steps after that point. Instead, mark the device as permanently failed. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org> (cherry picked from e06b942521eb2cdaf232726f45a820d5837acb12 commit)
-
由 Linas Vepstas 提交于
234-eeh-find-pe.patch The find_device_pe() routine is duplicated in two files. Remove one of the two copies, declare the other extern. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org> (cherry picked from 48408e708282d4d0269136ff27ea5acbd9410b5a commit)
-
由 Linas Vepstas 提交于
Various PCI bus errors can be signaled by newer PCI controllers. The core error recovery routines are architecture dependent. This patch adds a recovery infrastructure for the PPC64 pSeries systems. Signed-off-by: NLinas Vepstas <linas@austin.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org> (cherry picked from e8ca11b460c4c9c7fa6b529be221529ebd770e38 commit)
-