In the GICv3 redistributor there are the PENDBASER and PROPBASER
registers which we did not emulate so far, as they only make sense
when having an ITS. In preparation for that emulate those MMIO
accesses by storing the 64-bit data written into it into a variable
which we later read in the ITS emulation.
We also sanitise the registers, making sure RES0 regions are respected
and checking for valid memory attributes.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NEric Auger <eric.auger@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In the moment our struct vgic_irq's are statically allocated at guest
creation time. So getting a pointer to an IRQ structure is trivial and
safe. LPIs are more dynamic, they can be mapped and unmapped at any time
during the guest's _runtime_.
In preparation for supporting LPIs we introduce reference counting for
those structures using the kernel's kref infrastructure.
Since private IRQs and SPIs are statically allocated, we avoid actually
refcounting them, since they would never be released anyway.
But we take provisions to increase the refcount when an IRQ gets onto a
VCPU list and decrease it when it gets removed. Also this introduces
vgic_put_irq(), which wraps kref_put and hides the release function from
the callers.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NEric Auger <eric.auger@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

kvm_register_device_ops() can return an error, so lets check its return
value and propagate this up the call chain.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NEric Auger <eric.auger@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When reading back from the list registers, we need to perform
two actions for level interrupts:
1) clear the soft-pending bit if the interrupt is not pending
   anymore *in the list register*
2) resample the line level and propagate it to the pending state

But these two actions shouldn't be linked, and we should *always*
resample the line level, no matter what state is in the list
register. Otherwise, we may end-up injecting spurious interrupts
that have been already retired.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Enable the VGIC operation by properly initialising the registers
in the hypervisor GIC interface.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>

map_resources is the last initialization step. It is executed on
first VCPU run. At that stage the code checks that userspace has provided
the base addresses for the relevant VGIC regions, which depend on the
type of VGIC that is exposed to the guest.  Also we check if the two
regions overlap.
If the checks succeeded, we register the respective register frames with
the kvm_io_bus framework.

If we emulate a GICv2, the function also forces vgic_init execution if
it has not been executed yet. Also we map the virtual GIC CPU interface
onto the guest's CPU interface.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>

This patch allocates and initializes the data structures used
to model the vgic distributor and virtual cpu interfaces. At that
stage the number of IRQs and number of virtual CPUs is frozen.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>

Implements kvm_vgic_hyp_init and vgic_probe function.
This uses the new firmware independent VGIC probing to support both ACPI
and DT based systems (code from Marc Zyngier).

The vgic_global struct is enriched with new fields populated
by those functions.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>

Since the GIC CPU interface is always virtualized by the hardware,
we don't have CPU interface state information readily available in our
emulation if userland wants to save or restore it.
Fortunately the GIC hypervisor interface provides the VMCR register to
access the required virtual CPU interface bits.
Provide wrappers for GICv2 and GICv3 hosts to have access to this
register.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>

As the GICv3 virtual interface registers differ from their GICv2
siblings, we need different handlers for processing maintenance
interrupts and reading/writing to the LRs.
Implement the respective handler functions and connect them to
existing code to be called if the host is using a GICv3.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>