Clean up whitespace, capitalization, etc. in comments.  No functional
change intended.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

No functional change intended.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

[ Note, this is a Git cherry-pick of the following commit:

    506458ef ("locking/barriers: Convert users of lockless_dereference() to READ_ONCE()")

  ... for easier x86 PTI code testing and back-porting. ]

READ_ONCE() now has an implicit smp_read_barrier_depends() call, so it
can be used instead of lockless_dereference() without any change in
semantics.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1508840570-22169-4-git-send-email-will.deacon@arm.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

We'd like to use the 'PTI' acronym for 'Page Table Isolation' - free up the
namespace by renaming the <linux/pti.h> driver header to <linux/intel-pti.h>.

(Also standardize the header guard name while at it.)

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Currently mdio read/write takes around ~115us as the timeout
between status check is set to 100us.
By reducing the timeout to 1us mdio read/write takes ~15us to
complete. This improves the link up event response.
Signed-off-by: NHemanth Puranik <hpuranik@codeaurora.org>
Acked-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for Telit ME910 PID 0x1101.
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a suffix to distinguish kernel mainline version and aquantia releases
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On very first start we should read out current HW counter values
to make diff based calculations later.
This also should be done each time NIC gets down/up or wakes up
after sleep state. We reset link state explicitly to prevent diffs
from being summed this first time.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce timeout from 2 secs to 1 sec. If link is down,
reduce it to 500msec. This speeds up link detection.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This metric comes from HW and is also diff-calculated, like other counters
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Originally they were filled from ring sw counters.
These sometimes incorrectly calculate byte and packet amounts
when using LRO/LSO and jumboframes. Filling ndev counters from
hardware makes them precise.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device hardware provides only 32bit counters. Using these directly
causes byte counters to overflow soon. A separate nic level structure
with 64 bit counters is now used to collect incrementally all the stats
and report these counters to ethtool stats and ndev stats.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Systems with large MRRS on device (2K, 4K) with high data rates and/or
large MTU, atlantic observes DMA packet buffer overflow. On some systems
that causes PCIe transaction errors, hardware NMIs or datapath freeze.
This patch
1) Limits MRRS from device side to 2K (thats maximum our hardware supports)
2) Limit maximum size of outstanding TX DMA data read requests. This makes
hardware buffers running fine.
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different hardware device Ids correspond to different maximum speed
available. Extra checks were added for devices D108 and D109 to
remove unsupported speeds from these device capabilities list.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modifying the flags of an IP addr object needs to be protected against
eg. concurrent removal of the same object from the IP table.

Fixes: 5f78e29c ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When takeover is switched off, current code clears the 'TAKEOVER' flag on
all IPs. But the flag is also used for RXIP addresses, and those should
not be affected by the takeover mode.
Fix the behaviour by consistenly applying takover logic to NORMAL
addresses only.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just as for an explicit enable/disable, toggling the takeover mode also
requires that the IP addresses get updated. Otherwise all IPs that were
added to the table before the mode-toggle, get registered with the old
settings.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Learning is currently enabled for ports which are OVS slaves -
even though OVS doesn't need this indication.
Since we're not associating a fid with the port, HW would continuously
notify driver of learned [& aged] MACs which would be logged as errors.

Fixes: 2b94e58d ("mlxsw: spectrum: Allow ports to work under OVS master")
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously enabled clks are only disabled if clk_prepare_enable() fails.
However, there are other error paths were the previously enabled
clocks are not disabled.

To fix the problem, fsl_disable_clocks() now takes the number of clocks
that shall be disabled + unprepared. For existing calls were all clocks
were already successfully prepared + enabled, DMAMUX_NR is passed to
disable + unprepare all clocks.

In error paths were only some clocks were successfully prepared +
enabled the loop counter is passed, in order to disable + unprepare
all successfully prepared + enabled clocks.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAndreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Add a variant of rbtree_replace_node() that maintains the leftmost cache
of struct rbtree_root_cached when replacing nodes within the rbtree.

As drm_mm is the only rb_replace_node() being used on an interval tree,
the mistake looks fairly self-contained.  Furthermore the only user of
drm_mm_replace_node() is its testsuite...

Testcase: igt/drm_mm/replace

Link: http://lkml.kernel.org/r/20171122100729.3742-1-chris@chris-wilson.co.uk
Link: https://patchwork.freedesktop.org/patch/msgid/20171109212435.9265-1-chris@chris-wilson.co.uk
Fixes: f808c13f ("lib/interval_tree: fast overlap detection")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recent rework of the virtio_mmio probe/remove paths balanced a
devm_ioremap() with an iounmap() rather than its devm variant. This ends
up corrupting the devm datastructures, and results in the following
boot-time splat on arm64 under QEMU 2.9.0:

[    3.450397] ------------[ cut here ]------------
[    3.453822] Trying to vfree() nonexistent vm area (00000000c05b4844)
[    3.460534] WARNING: CPU: 1 PID: 1 at mm/vmalloc.c:1525 __vunmap+0x1b8/0x220
[    3.475898] Kernel panic - not syncing: panic_on_warn set ...
[    3.475898]
[    3.493933] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc3 #1
[    3.513109] Hardware name: linux,dummy-virt (DT)
[    3.525382] Call trace:
[    3.531683]  dump_backtrace+0x0/0x368
[    3.543921]  show_stack+0x20/0x30
[    3.547767]  dump_stack+0x108/0x164
[    3.559584]  panic+0x25c/0x51c
[    3.569184]  __warn+0x29c/0x31c
[    3.576023]  report_bug+0x1d4/0x290
[    3.586069]  bug_handler.part.2+0x40/0x100
[    3.597820]  bug_handler+0x4c/0x88
[    3.608400]  brk_handler+0x11c/0x218
[    3.613430]  do_debug_exception+0xe8/0x318
[    3.627370]  el1_dbg+0x18/0x78
[    3.634037]  __vunmap+0x1b8/0x220
[    3.648747]  vunmap+0x6c/0xc0
[    3.653864]  __iounmap+0x44/0x58
[    3.659771]  devm_ioremap_release+0x34/0x68
[    3.672983]  release_nodes+0x404/0x880
[    3.683543]  devres_release_all+0x6c/0xe8
[    3.695692]  driver_probe_device+0x250/0x828
[    3.706187]  __driver_attach+0x190/0x210
[    3.717645]  bus_for_each_dev+0x14c/0x1f0
[    3.728633]  driver_attach+0x48/0x78
[    3.740249]  bus_add_driver+0x26c/0x5b8
[    3.752248]  driver_register+0x16c/0x398
[    3.757211]  __platform_driver_register+0xd8/0x128
[    3.770860]  virtio_mmio_init+0x1c/0x24
[    3.782671]  do_one_initcall+0xe0/0x398
[    3.791890]  kernel_init_freeable+0x594/0x660
[    3.798514]  kernel_init+0x18/0x190
[    3.810220]  ret_from_fork+0x10/0x18

To fix this, we can simply rip out the explicit cleanup that the devm
infrastructure will do for us when our probe function returns an error
code, or when our remove function returns.

We only need to ensure that we call put_device() if a call to
register_virtio_device() fails in the probe path.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Fixes: 7eb781b1 ("virtio_mmio: add cleanup for virtio_mmio_probe")
Fixes: 25f32223 ("virtio_mmio: add cleanup for virtio_mmio_remove")
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: weiping zhang <zhangweiping@didichuxing.com>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cohuck@redhat.com>

This case can been seen when creating the lease with the same objects passed.

[  605.515097] 2 locks held by testapp/3337:
[  605.519027]  #0:  (&dev->mode_config.idr_mutex){......}, at: [<ffff0000085f1664>] drm_mode_create_lease_ioctl+0x384/0x858
[  605.530045]  #1:  (&dev->mode_config.idr_mutex){......}, at: [<ffff0000085f11bc>] drm_lease_destroy+0x2c/0x110

Which was causing the process to hang:

[  605.398827] [<ffff0000080856cc>] __switch_to+0x94/0xa8
[  605.404030] [<ffff000008c05d00>] __schedule+0x1b0/0x698
[  605.409322] [<ffff000008c06224>] schedule+0x3c/0xa8
[  605.414260] [<ffff000008c06628>] schedule_preempt_disabled+0x20/0x38
[  605.420677] [<ffff000008c07370>] mutex_lock_nested+0x158/0x340
[  605.426572] [<ffff0000085f11bc>] drm_lease_destroy+0x2c/0x110
[  605.432389] [<ffff0000085cecf0>] drm_master_put+0xc0/0xc8
[  605.437845] [<ffff0000085f175c>] drm_mode_create_lease_ioctl+0x47c/0x858
[  605.444612] [<ffff0000085d4460>] drm_ioctl+0x198/0x448
[  605.449811] [<ffff000008201134>] do_vfs_ioctl+0xa4/0x748
[  605.455192] [<ffff000008201864>] SyS_ioctl+0x8c/0xa0
[  605.460216] [<ffff000008082f4c>] __sys_trace_return+0x0/0x4

drm_mode_create_lease_ioctl() calls drm_lease_create() which acquires a lock
on dev->mode_config.idr_mutex. In case of failure, drm_lease_create() calls
drm_master_put() which in turn tries to acquire the same lock when calling
drm_lease_destroy().

v2: - Reverse the order at exit in case of fail, so that unlocking takes place
before dropping the reference.
    - Include detail information about deadlock (Daniel Vetter)
Signed-off-by: NMarius Vlad <marius-cristian.vlad@nxp.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213181048.32719-1-marius-cristian.vlad@nxp.com

PROBE_DEFER also uses system_wq to reprobe drivers, which means when
that again fails, and we try to flush the overall system_wq (to get
all the delayed connectore cleanup work_struct completed), we
deadlock.

Fix this by using just a single cleanup work, so that we can only
flush that one and don't block on anything else. That means a free
list plus locking, a standard pattern.

v2:
- Correctly free connectors only on last ref. Oops (Chris).
- use llist_head/node (Chris).

v3
- Add init_llist_head (Chris).

Fixes: a703c550 ("drm: safely free connectors from connector_iter")
Fixes: 613051da ("drm: locking&new iterators for connector_list")
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: <stable@vger.kernel.org> # v4.11+: 613051da ("drm: locking&new iterators for connector_list"
Cc: <stable@vger.kernel.org> # v4.11+
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Guillaume Tucker <guillaume.tucker@collabora.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Matt Hart <matthew.hart@linaro.org>
Cc: Thierry Escande <thierry.escande@collabora.co.uk>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213124936.17914-1-daniel.vetter@ffwll.ch

Before this patch, the stats_lock was acquired twice. In between the
locks Driver sent command to gather some more statistics (per priority
and counter statistics). If the stats lock was acquired by get
statistics NDO in between we would have report out of sync counters.

Fix this by collecting all stats from Firmware in advance and then
fill the Software structs under one lock.

Fixes: 0b131561 ("net/mlx4_en: Add Flow control statistics display via ethtool")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The field res_free indicates the total number of counters which are
available for allocation (reserved and unreserved). Fixed a bug where
the reserved counters were subtracted from res_free before any
allocation was performed.

Before this fix, free counters which were not reserved could not be
allocated.

Fixes: 9de92c60 ("net/mlx4_core: Adjust counter grant policy in the resource tracker")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the minimal MTU threshold for running loopback selftest.
MTU should be big enough to include packet payload, NET_IP_ALIGN,
Ethernet headers and preamble length.

Fixes: e7c1c2c4 ("mlx4_en: Added self diagnostics test implementation")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When in SGMII-to-Copper mode, the fiber page is used for the MAC facing
link, and does not require configuration of the fiber auto-negotiation
settings.  Avoid trying.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to handle multi-port SKGE boards was freeing IRQ
twice. The first one was under lock and might sleep.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function meson_gxl_read_status is local to the source and does
not need to be in global scope, so make it static.

Cleans up sparse warning:
symbol 'meson_gxl_read_status' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure that all mdio devices populate the struct device fwnode pointer
as well as the of_node pointer to allow drivers that wish to use
fwnode APIs to work.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a PHY has the BMCR_PDOWN bit set, it may decide to ignore writes
to other registers, or reset the registers to power-on defaults.
Micrel PHYs do this for their interrupt registers.

The current structure of phylib tries to enable interrupts before
resuming (and releasing) the BMCR_PDOWN bit.  This fails, causing
Micrel PHYs to stop working after a suspend/resume sequence if they
are using interrupts.

Fix this by ensuring that the PHY driver resume methods do not take
the phydev->lock mutex themselves, but the callers of phy_resume()
take that lock.  This then allows us to move the call to phy_resume()
before we enable interrupts in phy_start().
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XGMII is a 32-bit bus plus two clock signals per direction.  XAUI is
four serial lanes per direction.  The 88e6190 supports XAUI but not
XGMII as it doesn't have enough pins.  The same is true of 88e6176.

Match on PHY_INTERFACE_MODE_XAUI for the XAUI port type, but keep
accepting XGMII for backwards compatibility.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver may sleep under a spinlock.
The function call path is:
rr_close (acquire the spinlock)
  free_irq --> may sleep

To fix it, free_irq is moved to the place without holding the spinlock.

This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).

Changes since v2 [1]:
* Merged with latest code changes

Changes since v1:
Update made thanks to David's review, much appreciated David.
* Improved inconsistent failure handling of clock rate setting
* For completeness of usecase, added arc_emac_probe error handling
Signed-off-by: NBranislav Radocaj <branislav@radocaj.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sierra Wireless EM7565 is an Qualcomm MDM9x50 based M.2 modem.
The USB id is added to qmi_wwan.c to allow QMI communication
with the EM7565.
Signed-off-by: NSebastian Sjoholm <ssjoholm@mac.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

memalloc_noio_save modifies the behavior of MM, we must restore it after
we are done.

Fixes: d83187dd ("IB/IPoIB: Convert IPoIB to memalloc_noio_* calls")
Signed-off-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

This reverts commit fbf3d034.

As of commit 56086910 ("clk: renesas: cpg-mssr: Restore module
clocks during resume"), the workaround is no longer needed.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a set of values in the drm_display_info structure for each
connector which hold information derived from EDID. These are computed
in drm_add_display_info. Before this patch, that was only called in
drm_add_edid_modes. This meant that they were only set when EDID was
present and never reset when EDID was not, as happened when the
display was disconnected.

One of these fields, non_desktop, is used from
drm_mode_connector_update_edid_property, the function responsible for
assigning the new edid value to the application-visible property.

Various drivers call these two functions (drm_add_edid_modes and
drm_mode_connector_update_edid_property) in different orders. This
means that even when EDID is present, the drm_display_info fields may
not have been computed at the time that
drm_mode_connector_update_edid_property used the non_desktop value to
set the non_desktop property.

I've added a public function (drm_reset_display_info) that resets the
drm_display_info field values to default values and then made the
drm_add_display_info function public. These two functions are now
called directly from drm_mode_connector_update_edid_property so that
the drm_display_info fields are always computed from the current EDID
information before being used in that function.

This means that the drm_display_info values are often computed twice,
once when the EDID property it set and a second time when EDID is used
to compute modes for the device. The alternative would be to uniformly
ensure that the values were computed once before being used, which
would require that all drivers reliably invoke the two paths in the
same order. The computation is inexpensive enough that it seems more
maintainable in the long term to simply compute them in both paths.

The API to drm_add_display_info has been changed so that it no longer
takes the set of edid-based quirks as a parameter. Rather, it now
computes those quirks itself and returns them for further use by
drm_add_edid_modes.

This patch also includes a number of 'const' additions caused by
drm_mode_connector_update_edid_property taking a 'const struct edid *'
parameter and wanting to pass that along to drm_add_display_info.

v2: after review by Daniel Vetter <daniel.vetter@ffwll.ch>

	Removed EXPORT_SYMBOL_GPL for drm_reset_display_info and
	drm_add_display_info.

	Added FIXME in drm_mode_connector_update_edid_property about
	potentially merging that with drm_add_edid_modes to avoid
	the need for two driver calls.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213084427.31199-1-keithp@keithp.com
(danvet: cherry picked from commit 12a889bf4bca ("drm: rework delayed
connector cleanup in connector_iter") from drm-misc-next since
functional conflict with changes in -next and we need to make sure
both have the right version and nothing gets lost.)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>