which are quite a few. It should be evident that dealing with that
many options is a bit complex.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>

And also mention that you cannot do any pci_reset_function,
pci_reset_slot, or such calls. This is because they take the same
lock as SysFS does - and we would end up with a dead-lock if
we call those functions.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>

When the toolstack wants us to drop or add an PCI device it
changes the XenBus state to Configuring - and as result of that
we find out which devices we should still be exporting out and
which ones not. For the ones we don't need anymore we need to
do an PCI reset so that it is ready for the next guest.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>

We were doing the operations of freeing and reset in the wrong
order. Granted nothing broke because the reset functions just
set bar->which = 0.

But nonethless this was incorrect.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NJan Beulich <jbeulich@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>

We are using 'psdev->dev','found_psdev->dev', and 'dev' at the
same time - and they all point to the same structure.

To keep it straight lets just use one - 'dev'.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NJan Beulich <jbeulich@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>

_PAGE_IOMAP is used in xen_remap_domain_mfn_range() to prevent the
pfn_pte() call in remap_area_mfn_pte_fn() from using the p2m to translate
the MFN.  If mfn_pte() is used instead, the p2m look up is avoided and
the use of _PAGE_IOMAP is no longer needed.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

PCI devices may have BARs located above the end of RAM so mark such
frames as identity frames in the p2m (instead of the default of
missing).

PFNs outside the p2m (above MAX_P2M_PFN) are also considered to be
identity frames for the same reason.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

In xen_add_extra_mem(), if the WARN() checks for bad MFNs trigger it is
likely that they will trigger at lot, spamming the log.

Use WARN_ONCE() instead.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Large (multi-GB) identity ranges currently require a unique middle page
(filled with p2m_identity entries) per 1 GB region.

Similar to the common p2m_mid_missing middle page for large missing
regions, introduce a p2m_mid_identity page (filled with p2m_identity
entries) which can be used instead.

set_phys_range_identity() thus only needs to allocate new middle pages
at the beginning and end of the range.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Allow set_phys_range_identity() to work with a range that overlaps
MAX_P2M_PFN by clamping pfn_e to MAX_P2M_PFN.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

early_p2m_alloc_middle() allocates a new leaf page and
early_p2m_alloc() allocates a new middle page.  This is confusing.

Swap the names so they match what the functions actually do.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Execution is not going to continue after telling Xen about the crash.
Let other panic notifiers run by postponing the final hypercall as much
as possible.
Signed-off-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Introduce HYPERVISOR_suspend() and a few additional empty stubs for
Xen arch specific functions called by drivers/xen/manage.c.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

New architectures currently have to provide implementations of 5 different
functions: xen_arch_pre_suspend(), xen_arch_post_suspend(),
xen_arch_hvm_post_suspend(), xen_mm_pin_all(), and xen_mm_unpin_all().

Refactor the suspend code to only require xen_arch_pre_suspend() and
xen_arch_post_suspend().
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>

"arm: xen: implement multicall hypercall support." forgot to do this.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>

virt_to_pfn has been defined in arch/arm/include/asm/memory.h by commit
e26a9e00 "ARM: Better virt_to_page() handling" and Xen has come to rely
on it.  Introduce virt_to_pfn on arm64 too.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>

virt_to_pfn has been defined in asm/memory.h by the commit e26a9e00 "ARM: Better
virt_to_page() handling"

This will result of a compilation warning when CONFIG_XEN is enabled.

arch/arm/include/asm/xen/page.h:80:0: warning: "virt_to_pfn" redefined [enabled by default]
 #define virt_to_pfn(v)          (PFN_DOWN(__pa(v)))
 ^
In file included from arch/arm/include/asm/page.h:163:0,
                 from arch/arm/include/asm/xen/page.h:4,
                 from include/xen/page.h:4,
                 from arch/arm/xen/grant-table.c:33:

The definition in memory.h is nearly the same (it directly expand PFN_DOWN),
so we can safely drop virt_to_pfn in xen include.
Signed-off-by: NJulien Grall <julien.grall@linaro.org>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

As part of this make the usual change to xen_ulong_t in place of unsigned long.
This change has no impact on x86.

The Linux definition of struct multicall_entry.result differs from the Xen
definition, I think for good reasons, and used a long rather than an unsigned
long. Therefore introduce a xen_long_t, which is a long on x86 architectures
and a signed 64-bit integer on ARM.

Use uint32_t nr_calls on x86 for consistency with the ARM definition.

Build tested on amd64 and i386 builds. Runtime tested on ARM.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Pull input updates from Dmitry Torokhov:
 "The main change is that we now publish "firmware ID" for the serio
  devices to help userspace figure out the kind of touchpads it is
  dealing with: i8042 will export PS/2 port's PNP IDs as firmware IDs.

  You will also get more quirks for Synaptics touchpads in various
  Lenovo laptops, a change to elantech driver to recognize even more
  models, and fixups to wacom and couple other drivers"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elantech - add support for newer elantech touchpads
  Input: soc_button_array - fix a crash during rmmod
  Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1
  Input: synaptics - report INPUT_PROP_TOPBUTTONPAD property
  Input: Add INPUT_PROP_TOPBUTTONPAD device property
  Input: i8042 - add firmware_id support
  Input: serio - add firmware_id sysfs attribute
  Input: wacom - handle 1024 pressure levels in wacom_tpc_pen
  Input: wacom - references to 'wacom->data' should use 'unsigned char*'
  Input: wacom - override 'pressure_max' with value from HID_USAGE_PRESSURE
  Input: wacom - use full 32-bit HID Usage value in switch statement
  Input: wacom - missed the last bit of expresskey for DTU-1031
  Input: ads7846 - fix device usage within attribute show
  Input: da9055_onkey - remove use of regmap_irq_get_virq()

Pull radeon drm fixes from Dave Airlie:
 "This is just radeon fixes, primarily the two pll fix and the aux fix,
  it also disables dpm on rv770 gpus, fixes driver reloading, and fixes
  two issues with runtime PM on some GPUS"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: don't allow runpm=1 on systems with out ATPX
  drm/radeon: fix ATPX detection on non-VGA GPUs
  drm/radeon/pm: don't walk the crtc list before it has been initialized (v2)
  drm/radeon: properly unregister hwmon interface (v2)
  drm/radeon: fix count in cik_sdma_ring_test()
  drm/radeon/aux: fix hpd assignment for aux bus
  drm/radeon: improve PLL limit handling in post div calculation
  drm/radeon: use fixed PPL ref divider if needed
  drm/radeon: disable dpm on rv770 by default

Newer elantech touchpads are not recognized by the current driver, since it
fails to detect their firmware version number. This prevents more advanced
touchpad features from being usable such as two-finger scrolling. This
patch allows newer touchpads to be detected and be fully functional. Tested
on Sony Vaio SVF13N17PXB.
Signed-off-by: NJordan Rife <jrife0@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When the system has zero or one button available, trying to rmmod
soc_button_array will cause crash. Fix this by properly handling -ENODEV
in probe().
Signed-off-by: NLejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

1. Further PLL parameter fixes.
2. Fixes for HPD on DP
3. Could of different PM fixes
4. Disabling DPM on RV770

* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: don't allow runpm=1 on systems with out ATPX
  drm/radeon: fix ATPX detection on non-VGA GPUs
  drm/radeon/pm: don't walk the crtc list before it has been initialized (v2)
  drm/radeon: properly unregister hwmon interface (v2)
  drm/radeon: fix count in cik_sdma_ring_test()
  drm/radeon/aux: fix hpd assignment for aux bus
  drm/radeon: improve PLL limit handling in post div calculation
  drm/radeon: use fixed PPL ref divider if needed
  drm/radeon: disable dpm on rv770 by default

fixup_user_fault() is used by the futex code when the direct user access
fails, and the futex code wants it to either map in the page in a usable
form or return an error.  It relied on handle_mm_fault() to map the
page, and correctly checked the error return from that, but while that
does map the page, it doesn't actually guarantee that the page will be
mapped with sufficient permissions to be then accessed.

So do the appropriate tests of the vma access rights by hand.

[ Side note: arguably handle_mm_fault() could just do that itself, but
  we have traditionally done it in the caller, because some callers -
  notably get_user_pages() - have been able to access pages even when
  they are mapped with PROT_NONE.  Maybe we should re-visit that design
  decision, but in the meantime this is the minimal patch. ]

Found by Dave Jones running his trinity tool.
Reported-by: NDave Jones <davej@redhat.com>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull gpio fixes from Linus Walleij:
 "A small batch of GPIO fixes for the v3.15 series.  I expect more to
  come in but I'm a bit behind on mail, might as well get these to you
  right now:

   - Change a crucial semantic ordering in the GPIO irqchip helpers

   - Fix two nasty regressions in the ACPI gpiolib extensions"

* tag 'gpio-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio / ACPI: Prevent potential wrap of GPIO value on OpRegion read
  gpio / ACPI: Don't crash on NULL chip->dev
  gpio: set data first, then chip and handler

Pull x86 vdso fix from Peter Anvin:
 "This is a single build fix for building with gold as opposed to GNU
  ld.  It got queued up separately and was expected to be pushed during
  the merge window, but it got left behind"

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, vdso: Make the vdso linker script compatible with Gold

vgaswitcheroo and the ATPX ACPI methods are required to
power down the dGPU.

bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73901Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Some newer PX laptops have the pci device class
set to DISPLAY_OTHER rather than DISPLAY_VGA.  This
properly detects ATPX on those laptops.

Based on a patch from: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Cc: airlied@gmail.com

Avoids a crash in certain cases when thermal irqs are generated
before the display structures have been initialized.

v2: fix the vblank and vrefresh helpers as well

bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73931Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Need to properly unregister the hwmon device on driver
unload.

v2: minor clean up

bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73931Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Should be 5 rather than 4.
Noticed-by: NMathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NChristian König <christian.koenig@amd.com>

The hpd (hot plug detect) pin assignment got lost
in the conversion to to the common i2c over aux
code.  Without this information, aux transactions
do not work properly.  Fixes DP failures.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

Pull UML fixes from Richard Weinberger:
 "Assorted fixes for UML"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Memory corruption on startup
  um: Missing pipe handling
  uml: Simplify tempdir logic.

Pull ext4 fixes from Ted Ts'o:
 "These are regression and bug fixes for ext4.

  We had a number of new features in ext4 during this merge window
  (ZERO_RANGE and COLLAPSE_RANGE fallocate modes, renameat, etc.) so
  there were many more regression and bug fixes this time around.  It
  didn't help that xfstests hadn't been fully updated to fully stress
  test COLLAPSE_RANGE until after -rc1"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (31 commits)
  ext4: disable COLLAPSE_RANGE for bigalloc
  ext4: fix COLLAPSE_RANGE failure with 1KB block size
  ext4: use EINVAL if not a regular file in ext4_collapse_range()
  ext4: enforce we are operating on a regular file in ext4_zero_range()
  ext4: fix extent merging in ext4_ext_shift_path_extents()
  ext4: discard preallocations after removing space
  ext4: no need to truncate pagecache twice in collapse range
  ext4: fix removing status extents in ext4_collapse_range()
  ext4: use filemap_write_and_wait_range() correctly in collapse range
  ext4: use truncate_pagecache() in collapse range
  ext4: remove temporary shim used to merge COLLAPSE_RANGE and ZERO_RANGE
  ext4: fix ext4_count_free_clusters() with EXT4FS_DEBUG and bigalloc enabled
  ext4: always check ext4_ext_find_extent result
  ext4: fix error handling in ext4_ext_shift_extents
  ext4: silence sparse check warning for function ext4_trim_extent
  ext4: COLLAPSE_RANGE only works on extent-based files
  ext4: fix byte order problems introduced by the COLLAPSE_RANGE patches
  ext4: use i_size_read in ext4_unaligned_aio()
  fs: disallow all fallocate operation on active swapfile
  fs: move falloc collapse range check into the filesystem methods
  ...

The reverse case of this race (you must msync before read) is
well known. This is the not so common one.

It can be triggered only on systems which do a lot of task
switching and only at UML startup. If you are starting 200+ UMLs
~ 0.5% will always die without this fix.
Signed-off-by: NAnton Ivanov <antivano@cisco.com>
[rw: minor whitespace fixes]
Signed-off-by: NRichard Weinberger <richard@nod.at>

UML does not handle sigpipe. As a result when running it under
expect or redirecting the IO from the console to an external program
it will crash if the program stops or exits.
Signed-off-by: NAnton Ivanov <antivano@cisco.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>

Inferring the mount hierarchy correctly from /proc/mounts is hard when MS_MOVE
may have been used, and the previous code did it wrongly. This change simplifies
the logic to only require that /dev/shm be _on_ tmpfs (which can be checked
trivially with statfs) rather than that it be a _mountpoint_ of tmpfs, since
there isn't a compelling reason to be that strict. We also now check for tmpfs
on whatever directory we ultimately use so that the user is better informed.

This change also moves the more standard TMPDIR environment variable check ahead
of the others.

Applies to 3.12.
Signed-off-by: NTristan Schmelcher <tschmelcher@google.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>

Pull slave-dmaengine fixes from Vinod Koul:
 "Back from long weekend here in India and now the time to send fixes
  for slave dmaengine.
   - Dan's fix of sirf xlate code
   - Jean's fix for timberland
   - edma fixes by Sekhar for SG handling and Yuan for changing init
     call"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: fix eDMA driver as a subsys_initcall
  dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
  platform: Fix timberdale dependencies
  dma: edma: fix incorrect SG list handling

Pull iommu fixes from Joerg Roedel:
 "Fixes for regressions:

   - fix wrong IOMMU enumeration causing some SCSI device drivers
     initialization failures
   - ARM-SMMU fixes for a panic condition and a wrong return value"

* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
  iommu/arm-smmu: Return 0 on unmap failure
  iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
  iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
  iommu/vt-d: fix memory leakage caused by commit ea8ea460