[ Upstream commit 426a593e641ebf0d9288f0a2fcab644a86820220 ]

In the original ftmac100_interrupt(), the interrupts are only disabled when
the condition "netif_running(netdev)" is true. However, this condition
causes kerenl hang in the following case. When the user requests to
disable the network device, kernel will clear the bit __LINK_STATE_START
from the dev->state and then call the driver's ndo_stop function. Network
device interrupts are not blocked during this process. If an interrupt
occurs between clearing __LINK_STATE_START and stopping network device,
kernel cannot disable the interrupts due to the condition
"netif_running(netdev)" in the ISR. Hence, kernel will hang due to the
continuous interruption of the network device.

In order to solve the above problem, the interrupts of the network device
should always be disabled in the ISR without being restricted by the
condition "netif_running(netdev)".

[V2]
Remove unnecessary curly braces.
Signed-off-by: NVincent Chen <vincentc@andestech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a5681e20b541a507c7d4fd48ae4a4040d32ee1ef ]

This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.

Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: NJuliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit eb62cca9bee842e5b23bd0ddfb1f271ca95e8759 ]

The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.

The patch consists of 3 fixes:

 - When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
   returned PQ 0, which can potentially be another function's pq. Verify
   that flag is enabled, otherwise return default start_pq.

 - When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
   returned NULL and could lead to a segmentation fault. Return default
   start_pq instead.

 - A modulo operation was added to MCOS/VFS PQ getters to make sure the
   PQ returned is in range of the required flag.

Fixes: b5a9ee7c ("qed: Revise QM cofiguration")
Signed-off-by: NDenis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 276d43f0ae963312c0cd0e2b9a85fd11ac65dfcc ]

Fix the condition which verifies that only one flag is set. The API
bitmap_weight() should receive size in bits instead of bytes.

Fixes: b5a9ee7c ("qed: Revise QM cofiguration")
Signed-off-by: NDenis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e76ad21d070f79e566ac46ce0b0584c3c93e1b43 ]

During resume from hibernation if ena_restore_device fails,
ena_com_dev_reset() is called, and uses the readless read mechanism,
which was already destroyed by the call to
ena_com_mmio_reg_read_request_destroy(). This causes a NULL pointer
reference.

In this commit we switch the call order of the above two functions
to avoid this crash.

Fixes: d7703ddb ("net: ena: fix rare bug when failed restart/resume is followed by driver removal")
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a97b9565338350d70d8d971c4ee6f0d4fa967418 ]

Add missing semicolon.

Fixes: 291d57f67d244973 ("qed: Fix rdma_info structure allocation")
Cc: Michal Kalderon <michal.kalderon@cavium.com>
Cc: Denis Bolotin <denis.bolotin@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a463146e67c848cbab5ce706d6528281b7cded08 ]

UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow: 1802201963 + 1802201963 cannot be represented
in type 'int'

The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative.  Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.

Fixes: 5a0d0a61 ("mlx4: Structures and init/teardown for VF resource quotas")
Signed-off-by: NAya Levin <ayal@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3ea7e7ea53c9f6ee41cb69a29c375fe9dd9a56a7 ]

Initialize the uid variable to zero to avoid the compilation warning.

Fixes: 7a89399f ("net/mlx4: Add mlx4_bitmap zone allocator")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit bd85fbc2038a1bbe84990b23ff69b6fc81a32b2c ]

When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.

This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).

The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).

Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.

Fixes: e630664c ("mlx4_core: Add helper functions to support MR re-registration")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8dc5ae2d48976764cf3498e97963fa06befefb0e ]

Fix the year and month offset while storing it in
bnxt_fill_coredump_record().

Fixes: 6c5657d0 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ed4eac20dcffdad47709422e0cb925981b056668 ]

The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: NDenis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 291d57f67d2449737d1e370ab5b9a583818eaa0c ]

Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.

Fixes: 51ff1725 ("qed: Add support for RoCE hw init")
Signed-off-by: NMichal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: NDenis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e90202ed1cf9672c48a363c84a929932ebfe6fc0 ]

The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: NDenis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9aaa4e8ba12972d674caeefbc5f88d83235dd697 ]

Release PTT before entering error flow.
Signed-off-by: NDenis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 77e461d14ed141253573eeeb4d34eccc51e38328 ]

Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
  MFW - OCBB/OCSD functionality uses DMAE channel 14/15
  Driver 0-3 and 8-11 (for PF dmae operations)
         4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.

Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 68c8d209cd4337da4fa04c672f0b62bb735969bc ]

Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.

Fixes: 862e2b6a ("can: rcar_can: support all input clocks")
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: NChris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 207681fc5f3d5d398f106d1ae0080fc2373f707a ]

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
 variable 'udev' set but not used [-Wunused-but-set-variable]
  struct usb_device *udev;
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NMartin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b374e8686fc35ae124e62dc78725ea656ba1ef8a ]

When CONFIG_LEDS_CLASS is disabled, or it is a loadable module while
mt76 is built-in, we run into a link error:

drivers/net/wireless/mediatek/mt76/mac80211.o: In function `mt76_register_device':
mac80211.c:(.text+0xb78): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_of_led_classdev_register'

We don't really need a hard dependency here as the driver can presumably
work just fine without LEDs, so this follows the iwlwifi example and
adds a separate Kconfig option for the LED support, this will be available
whenever it will link, and otherwise the respective code gets left out from
the driver object.

Fixes: 17f1de56 ("mt76: add common code shared between multiple chipsets")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3401d42c7ea2d064d15c66698ff8eb96553179ce ]

Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.

This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
   Before: chnum:50 control_ch_num:36
    After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
   Before: chnum:114 control_ch_num:100
    After: chnum:114 control_ch_num:120

Fixes: 330994e8e8ec ("brcmfmac: fix for proper support of 160MHz bandwidth")
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit eab077aa84331afbda071a213925d4cdbca58941 upstream.

In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.

CC: stable <stable@vger.kernel.org>
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c85ddecae6e5e82ca3ae6f20c63f1d865e2ff5ea ]

After switching the r8169 driver to use phylib some user reported that
their network is broken. This was caused by the genphy PHY driver being
used instead of the dedicated PHY driver for the RTL8211B. Users
reported that loading the Realtek PHY driver module upfront fixes the
issue. See also this mail thread:
https://marc.info/?t=154279781800003&r=1&w=2
The issue is quite weird and the root cause seems to be somewhere in
the base driver core. The patch works around the issue and may be
removed once the actual issue is fixed.

The Fixes tag refers to the first reported occurrence of the issue.
The issue itself may have been existing much longer and it may affect
users of other network chips as well. Users typically will recognize
this issue only if their PHY stops working when being used with the
genphy driver.

Fixes: f1e911d5 ("r8169: add basic phylib support")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 18ba58e1c234ea1a2d9835ac8c1735d965ce4640 ]

We don't support partial csumed packet since its metadata will be lost
or incorrect during XDP processing. So fail the XDP set if guest_csum
feature is negotiated.

Fixes: f600b690 ("virtio_net: Add XDP support")
Reported-by: NJesper Dangaard Brouer <brouer@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pavel Popa <pashinho1990@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e59ff2c49ae16e1d179de679aca81405829aee6c ]

We don't disable VIRTIO_NET_F_GUEST_CSUM if XDP was set. This means we
can receive partial csumed packets with metadata kept in the
vnet_hdr. This may have several side effects:

- It could be overridden by header adjustment, thus is might be not
  correct after XDP processing.
- There's no way to pass such metadata information through
  XDP_REDIRECT to another driver.
- XDP does not support checksum offload right now.

So simply disable guest csum if possible in this the case of XDP.

Fixes: 3f93522f ("virtio-net: switch off offloads on demand if possible on XDP set")
Reported-by: NJesper Dangaard Brouer <brouer@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pavel Popa <pashinho1990@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6d0f60b0f8588fd4380ea5df9601e12fddd55ce2 ]

Set xdp_prog pointer to NULL if bpf_prog_add fails since that routine
reports the error code instead of NULL in case of failure and xdp_prog
pointer value is used in the driver to verify if XDP is currently
enabled.
Moreover report the error code to userspace if nicvf_xdp_setup fails

Fixes: 05c773f5 ("net: thunderx: Add basic XDP support")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 45611c61dd503454b2edae00aabe1e429ec49ebe ]

The bug is not easily reproducable, as it may occur very infrequently
(we had machines with 20minutes heavy downloading before it occurred)
However, on a virual machine (VMWare on Windows 10 host) it occurred
pretty frequently (1-2 seconds after a speedtest was started)

dev->tx_skb mab be freed via dev_kfree_skb_irq on a callback
before it is set.

This causes the following problems:
- double free of the skb or potential memory leak
- in dmesg: 'recvmsg bug' and 'recvmsg bug 2' and eventually
  general protection fault

Example dmesg output:
[  134.841986] ------------[ cut here ]------------
[  134.841987] recvmsg bug: copied 9C24A555 seq 9C24B557 rcvnxt 9C25A6B3 fl 0
[  134.841993] WARNING: CPU: 7 PID: 2629 at /build/linux-hwe-On9fm7/linux-hwe-4.15.0/net/ipv4/tcp.c:1865 tcp_recvmsg+0x44d/0xab0
[  134.841994] Modules linked in: ipheth(OE) kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd glue_helper cryptd vmw_balloon intel_rapl_perf joydev input_leds serio_raw vmw_vsock_vmci_transport vsock shpchp i2c_piix4 mac_hid binfmt_misc vmw_vmci parport_pc ppdev lp parport autofs4 vmw_pvscsi vmxnet3 hid_generic usbhid hid vmwgfx ttm drm_kms_helper syscopyarea sysfillrect mptspi mptscsih sysimgblt ahci psmouse fb_sys_fops pata_acpi mptbase libahci e1000 drm scsi_transport_spi
[  134.842046] CPU: 7 PID: 2629 Comm: python Tainted: G        W  OE    4.15.0-34-generic #37~16.04.1-Ubuntu
[  134.842046] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017
[  134.842048] RIP: 0010:tcp_recvmsg+0x44d/0xab0
[  134.842048] RSP: 0018:ffffa6630422bcc8 EFLAGS: 00010286
[  134.842049] RAX: 0000000000000000 RBX: ffff997616f4f200 RCX: 0000000000000006
[  134.842049] RDX: 0000000000000007 RSI: 0000000000000082 RDI: ffff9976257d6490
[  134.842050] RBP: ffffa6630422bd98 R08: 0000000000000001 R09: 000000000004bba4
[  134.842050] R10: 0000000001e00c6f R11: 000000000004bba4 R12: ffff99760dee3000
[  134.842051] R13: 0000000000000000 R14: ffff99760dee3514 R15: 0000000000000000
[  134.842051] FS:  00007fe332347700(0000) GS:ffff9976257c0000(0000) knlGS:0000000000000000
[  134.842052] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  134.842053] CR2: 0000000001e41000 CR3: 000000020e9b4006 CR4: 00000000003606e0
[  134.842055] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  134.842055] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  134.842057] Call Trace:
[  134.842060]  ? aa_sk_perm+0x53/0x1a0
[  134.842064]  inet_recvmsg+0x51/0xc0
[  134.842066]  sock_recvmsg+0x43/0x50
[  134.842070]  SYSC_recvfrom+0xe4/0x160
[  134.842072]  ? __schedule+0x3de/0x8b0
[  134.842075]  ? ktime_get_ts64+0x4c/0xf0
[  134.842079]  SyS_recvfrom+0xe/0x10
[  134.842082]  do_syscall_64+0x73/0x130
[  134.842086]  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[  134.842086] RIP: 0033:0x7fe331f5a81d
[  134.842088] RSP: 002b:00007ffe8da98398 EFLAGS: 00000246 ORIG_RAX: 000000000000002d
[  134.842090] RAX: ffffffffffffffda RBX: ffffffffffffffff RCX: 00007fe331f5a81d
[  134.842094] RDX: 00000000000003fb RSI: 0000000001e00874 RDI: 0000000000000003
[  134.842095] RBP: 00007fe32f642c70 R08: 0000000000000000 R09: 0000000000000000
[  134.842097] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe332347698
[  134.842099] R13: 0000000001b7e0a0 R14: 0000000001e00874 R15: 0000000000000000
[  134.842103] Code: 24 fd ff ff e9 cc fe ff ff 48 89 d8 41 8b 8c 24 10 05 00 00 44 8b 45 80 48 c7 c7 08 bd 59 8b 48 89 85 68 ff ff ff e8 b3 c4 7d ff <0f> 0b 48 8b 85 68 ff ff ff e9 e9 fe ff ff 41 8b 8c 24 10 05 00
[  134.842126] ---[ end trace b7138fc08c83147f ]---
[  134.842144] general protection fault: 0000 [#1] SMP PTI
[  134.842145] Modules linked in: ipheth(OE) kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd glue_helper cryptd vmw_balloon intel_rapl_perf joydev input_leds serio_raw vmw_vsock_vmci_transport vsock shpchp i2c_piix4 mac_hid binfmt_misc vmw_vmci parport_pc ppdev lp parport autofs4 vmw_pvscsi vmxnet3 hid_generic usbhid hid vmwgfx ttm drm_kms_helper syscopyarea sysfillrect mptspi mptscsih sysimgblt ahci psmouse fb_sys_fops pata_acpi mptbase libahci e1000 drm scsi_transport_spi
[  134.842161] CPU: 7 PID: 2629 Comm: python Tainted: G        W  OE    4.15.0-34-generic #37~16.04.1-Ubuntu
[  134.842162] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017
[  134.842164] RIP: 0010:tcp_close+0x2c6/0x440
[  134.842165] RSP: 0018:ffffa6630422bde8 EFLAGS: 00010202
[  134.842167] RAX: 0000000000000000 RBX: ffff99760dee3000 RCX: 0000000180400034
[  134.842168] RDX: 5c4afd407207a6c4 RSI: ffffe868495bd300 RDI: ffff997616f4f200
[  134.842169] RBP: ffffa6630422be08 R08: 0000000016f4d401 R09: 0000000180400034
[  134.842169] R10: ffffa6630422bd98 R11: 0000000000000000 R12: 000000000000600c
[  134.842170] R13: 0000000000000000 R14: ffff99760dee30c8 R15: ffff9975bd44fe00
[  134.842171] FS:  00007fe332347700(0000) GS:ffff9976257c0000(0000) knlGS:0000000000000000
[  134.842173] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  134.842174] CR2: 0000000001e41000 CR3: 000000020e9b4006 CR4: 00000000003606e0
[  134.842177] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  134.842178] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  134.842179] Call Trace:
[  134.842181]  inet_release+0x42/0x70
[  134.842183]  __sock_release+0x42/0xb0
[  134.842184]  sock_close+0x15/0x20
[  134.842187]  __fput+0xea/0x220
[  134.842189]  ____fput+0xe/0x10
[  134.842191]  task_work_run+0x8a/0xb0
[  134.842193]  exit_to_usermode_loop+0xc4/0xd0
[  134.842195]  do_syscall_64+0xf4/0x130
[  134.842197]  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[  134.842197] RIP: 0033:0x7fe331f5a560
[  134.842198] RSP: 002b:00007ffe8da982e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000003
[  134.842200] RAX: 0000000000000000 RBX: 00007fe32f642c70 RCX: 00007fe331f5a560
[  134.842201] RDX: 00000000008f5320 RSI: 0000000001cd4b50 RDI: 0000000000000003
[  134.842202] RBP: 00007fe32f6500f8 R08: 000000000000003c R09: 00000000009343c0
[  134.842203] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe32f6500d0
[  134.842204] R13: 00000000008f5320 R14: 00000000008f5320 R15: 0000000001cd4770
[  134.842205] Code: c8 00 00 00 45 31 e4 49 39 fe 75 4d eb 50 83 ab d8 00 00 00 01 48 8b 17 48 8b 47 08 48 c7 07 00 00 00 00 48 c7 47 08 00 00 00 00 <48> 89 42 08 48 89 10 0f b6 57 34 8b 47 2c 2b 47 28 83 e2 01 80
[  134.842226] RIP: tcp_close+0x2c6/0x440 RSP: ffffa6630422bde8
[  134.842227] ---[ end trace b7138fc08c831480 ]---

The proposed patch eliminates a potential racing condition.
Before, usb_submit_urb was called and _after_ that, the skb was attached
(dev->tx_skb). So, on a callback it was possible, however unlikely that the
skb was freed before it was set. That way (because dev->tx_skb was not set
to NULL after it was freed), it could happen that a skb from a earlier
transmission was freed a second time (and the skb we should have freed did
not get freed at all)

Now we free the skb directly in ipheth_tx(). It is not passed to the
callback anymore, eliminating the posibility of a double free of the same
skb. Depending on the retval of usb_submit_urb() we use dev_kfree_skb_any()
respectively dev_consume_skb_any() to free the skb.
Signed-off-by: NOliver Zweigle <Oliver.Zweigle@faro.com>
Signed-off-by: NBernd Eckstein <3ernd.Eckstein@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit cfc435198f53a6fa1f656d98466b24967ff457d0 ]

skb is freed via dev_kfree_skb_any, however, skb->len is read then. This
may result in a use-after-free bug.

Fixes: e6161d64 ("rapidio/rionet: rework driver initialization and removal")
Signed-off-by: NPan Bian <bianpan2016@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ef2a7cf1d8831535b8991459567b385661eb4a36 ]

Reset snd_queue tso_hdrs pointer to NULL in nicvf_free_snd_queue routine
since it is used to check if tso dma descriptor queue has been previously
allocated. The issue can be triggered with the following reproducer:

$ip link set dev enP2p1s0v0 xdpdrv obj xdp_dummy.o
$ip link set dev enP2p1s0v0 xdpdrv off

[  341.467649] WARNING: CPU: 74 PID: 2158 at mm/vmalloc.c:1511 __vunmap+0x98/0xe0
[  341.515010] Hardware name: GIGABYTE H270-T70/MT70-HD0, BIOS T49 02/02/2018
[  341.521874] pstate: 60400005 (nZCv daif +PAN -UAO)
[  341.526654] pc : __vunmap+0x98/0xe0
[  341.530132] lr : __vunmap+0x98/0xe0
[  341.533609] sp : ffff00001c5db860
[  341.536913] x29: ffff00001c5db860 x28: 0000000000020000
[  341.542214] x27: ffff810feb5090b0 x26: ffff000017e57000
[  341.547515] x25: 0000000000000000 x24: 00000000fbd00000
[  341.552816] x23: 0000000000000000 x22: ffff810feb5090b0
[  341.558117] x21: 0000000000000000 x20: 0000000000000000
[  341.563418] x19: ffff000017e57000 x18: 0000000000000000
[  341.568719] x17: 0000000000000000 x16: 0000000000000000
[  341.574020] x15: 0000000000000010 x14: ffffffffffffffff
[  341.579321] x13: ffff00008985eb27 x12: ffff00000985eb2f
[  341.584622] x11: ffff0000096b3000 x10: ffff00001c5db510
[  341.589923] x9 : 00000000ffffffd0 x8 : ffff0000086868e8
[  341.595224] x7 : 3430303030303030 x6 : 00000000000006ef
[  341.600525] x5 : 00000000003fffff x4 : 0000000000000000
[  341.605825] x3 : 0000000000000000 x2 : ffffffffffffffff
[  341.611126] x1 : ffff0000096b3728 x0 : 0000000000000038
[  341.616428] Call trace:
[  341.618866]  __vunmap+0x98/0xe0
[  341.621997]  vunmap+0x3c/0x50
[  341.624961]  arch_dma_free+0x68/0xa0
[  341.628534]  dma_direct_free+0x50/0x80
[  341.632285]  nicvf_free_resources+0x160/0x2d8 [nicvf]
[  341.637327]  nicvf_config_data_transfer+0x174/0x5e8 [nicvf]
[  341.642890]  nicvf_stop+0x298/0x340 [nicvf]
[  341.647066]  __dev_close_many+0x9c/0x108
[  341.650977]  dev_close_many+0xa4/0x158
[  341.654720]  rollback_registered_many+0x140/0x530
[  341.659414]  rollback_registered+0x54/0x80
[  341.663499]  unregister_netdevice_queue+0x9c/0xe8
[  341.668192]  unregister_netdev+0x28/0x38
[  341.672106]  nicvf_remove+0xa4/0xa8 [nicvf]
[  341.676280]  nicvf_shutdown+0x20/0x30 [nicvf]
[  341.680630]  pci_device_shutdown+0x44/0x88
[  341.684720]  device_shutdown+0x144/0x250
[  341.688640]  kernel_restart_prepare+0x44/0x50
[  341.692986]  kernel_restart+0x20/0x68
[  341.696638]  __se_sys_reboot+0x210/0x238
[  341.700550]  __arm64_sys_reboot+0x24/0x30
[  341.704555]  el0_svc_handler+0x94/0x110
[  341.708382]  el0_svc+0x8/0xc
[  341.711252] ---[ end trace 3f4019c8439959c9 ]---
[  341.715874] page:ffff7e0003ef4000 count:0 mapcount:0 mapping:0000000000000000 index:0x4
[  341.723872] flags: 0x1fffe000000000()
[  341.727527] raw: 001fffe000000000 ffff7e0003f1a008 ffff7e0003ef4048 0000000000000000
[  341.735263] raw: 0000000000000004 0000000000000000 00000000ffffffff 0000000000000000
[  341.742994] page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)

where xdp_dummy.c is a simple bpf program that forwards the incoming
frames to the network stack (available here:
https://github.com/altoor/xdp_walkthrough_examples/blob/master/sample_1/xdp_dummy.c)

Fixes: 05c773f5 ("net: thunderx: Add basic XDP support")
Fixes: 4863dea3 ("net: Adding support for Cavium ThunderX network controller")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 07093b76476903f820d83d56c3040e656fb4d9e3 ]

The TX stats should be started with the tx_stats_syncp,
there seems to be a copy/paste error in the driver.
Signed-off-by: NAndreas Fiedler <andreas.fiedler@gmx.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit cc5922054131f9abefdc0622ae64fc55e6b2671d ]

The lan743x driver, when under heavy traffic load, has been noticed
to sometimes hang, or cause a kernel panic.

Debugging reveals that the TX napi poll routine was returning
the wrong value, 'weight'. Most other drivers return 0.
And call napi_complete, instead of napi_complete_done.

Additionally when creating the tx napi poll routine.
Changed netif_napi_add, to netif_tx_napi_add.

Updates for v3:
    changed 'fixes' tag to match defined format

Updates for v2:
use napi_complete, instead of napi_complete_done in
    lan743x_tx_napi_poll
use netif_tx_napi_add, instead of netif_napi_add for
    registration of tx napi poll routine

fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4df5ce9bc03e47d05f400e64aa32a82ec4cef419 ]

This driver was designed to work with both LAN7430 and LAN7431.
The only difference between the two is the LAN7431 has support
for external phy.

This change adds LAN7431 to the list of recognized devices
supported by this driver.

Updates for v2:
    changed 'fixes' tag to match defined format

fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e05237f9da42ee52e73acea0bb082d788e111229 upstream.

The previous patch changes the TX path to always use the last mailbox
regardless of the used offload scheme (rx-fifo or timestamp based). This
means members "tx_mb" and "tx_mb_idx" of the struct flexcan_priv don't
depend on the offload scheme, so replace them by compile time constants.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cbffaf7aa09edbaea2bc7dc440c945297095e2fd upstream.

Essentially this patch moves the TX mailbox to position 63, regardless
of timestamp based offloading or RX FIFO. So mainly the iflag register
usage regarding TX has changed. The rest is consolidating RX FIFO and
timestamp offloading as they now use both the same TX mailbox.

The reason is a very annoying behavior regarding sending RTR frames when
_not_ using RX FIFO:

If a TX mailbox sent a RTR frame it becomes a RX mailbox. For that
reason flexcan_irq disables the TX mailbox again. But if during the time
the RTR was sent and the TX mailbox is disabled a new CAN frames is
received, it is lost without notice. The reason is that so-called
"Move-in" process starts from the lowest mailbox which happen to be a TX
mailbox set to EMPTY.

Steps to reproduce (I used an imx7d):
1. generate regular bursts of messages
2. send a RTR from flexcan with higher priority than burst messages every
   1ms, e.g. cangen -I 0x100 -L 0 -g 1 -R can0
3. notice a lost message without notification after some seconds

When running an iperf in parallel this problem is occurring even more
frequently. Using filters is not possible as at least one single CAN-ID
is allowed. Handling the TX MB during RX is also not possible as there
is no race-free disable of RX MB.

There is still a slight window when the described problem can occur. But
for that all RX MB must be in use which is essentially next to an
overrun. Still there will be no indication if it ever occurs.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f164d0204b1156a7e0d8d1622c1a8d25752befec upstream.

If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing.  Bus state is "active".
Bringing the interface down and back up reconvenes the reception.  The
issue is not observed when the hi3110 is the sole device on the SPI bus.

Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.

Unfortunately the hi3110 datasheet is mum on the trigger type.  The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ed72bc8bcb9277061e753faf300b20f97323761c upstream.

Current flexcan driver will put TX-ECHO in regular unsorted way, in
this case TX-ECHO can come after the response to the same TXed message.
In some cases, for example for J1939 stack, things will break.
This patch is using new rx-offload API to put the messages just in the
right place.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d788905f68fd4714c82936f6f7f1d3644d7ae7ef upstream.

Currently, in case of bus error, driver will generate error message and put
in the tail of the message queue. To avoid confusions, this change should
place the bus related messages in proper order.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4530ec36bb1e0d24f41c33229694adacda3d5d89 upstream.

This function has nothing todo with error.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions

commit 55059f2b7f868cd43b3ad30e28e18347e1b46ace upstream.

Current CAN framework can't guarantee proper/chronological order
of RX and TX-ECHO messages. To make this possible, drivers should use
this functions instead of can_get_echo_skb().
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7da11ba5c5066dadc2e96835a6233d56d7b7764a upstream.

Prior to echoing a successfully transmitted CAN frame (by calling
can_get_echo_skb()), CAN drivers have to put the CAN frame (by calling
can_put_echo_skb() in the transmit function). These put and get function
take an index as parameter, which is used to identify the CAN frame.

A driver calling can_get_echo_skb() with a index not pointing to a skb
is a BUG, so add an appropriate error message.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

can: dev: __can_get_echo_skb(): Don't crash the kernel if can_priv::echo_skb is accessed out of bounds

commit e7a6994d043a1e31d5b17706a22ce33d2a3e4cdc upstream.

If the "struct can_priv::echo_skb" is accessed out of bounds would lead
to a kernel crash. Better print a sensible warning message instead and
try to recover.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 200f5c49f7a2cd694436bfc6cb0662b794c96736 upstream.

This patch replaces the use of "struct can_frame::can_dlc" by "struct
canfd_frame::len" to access the frame's length. As it is ensured that
both structures have a compatible memory layout for this member this is
no functional change. Futher, this compatibility is documented in a
comment.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>