David L Stevens says:

====================
sunvnet: add jumbo frames support

This patch set updates the sunvnet driver to version 1.6 of the VIO protocol
to support per-port exchange of MTU information and allow non-standard MTU
sizes, including jumbo frames.

Using large MTUs shows a nearly 5X throughput improvement Linux-Solaris
and > 10X throughput improvement Linux-Linux.

Changes from v8:
	-add a short timeout to free pending skbs if a new transmit doesn't
	 do it first per Dave Miller <davem@davemloft.net>
Changes from v7:
	-handle skb allocation failures in vnet_skb_shape()
	 per Dave Miller <davem@davemloft.net>
Changes from v6:
	-made kernel transmit path zero-copy to remove memory n^2 scaling issue
	 raised by Raghuram Kothakota <Raghuram.Kothakota@oracle.com>
Changes from v5:
	- fixed comment per Sowmini Varadhan <sowmini.varadhan@oracle.com>
Changes from v4:
	- changed VNET_MAXPACKET per David Laight <David.Laight@ACULAB.COM>
	- added cookies to support non-contiguous buffers of max size
Changes from v3:
	- added version functions per Dave Miller <davem@davemloft.net>
	- moved rmtu to vnet_port per Dave Miller <davem@davemloft.net>
	- explicitly set options bits and capability flags to 0 per
		Raghuram Kothakota <Raghuram.Kothakota@oracle.com>
Changes from v2:
	- make checkpatch clean
Changes from v1:
	- fix brace formatting per Dave Miller <davem@davemloft.net>
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sends ICMP and ICMPv6 messages for Path MTU Discovery when a remote
port MTU is smaller than the device MTU. This allows mixing newer VIO protocol
devices that support MTU negotiation with older devices that do not on the
same vswitch. It also allows Linux-Linux LDOMs to use 64K-1 data packets even
though Solaris vswitch is limited to <16K MTU.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows an admin to set the MTU on a sunvnet device to arbitrary
values between the minimum (68) and maximum (65535) IPv4 packet sizes.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes pre-allocated transmit buffers and instead directly maps
pending packets on demand. This saves O(n^2) maximum-sized transmit buffers,
for n hosts on a vswitch, as well as a copy to those buffers.

Single-stream TCP throughput linux-solaris dropped ~5% for 1500-byte MTU,
but linux-linux at 1500-bytes increased ~20%.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch upgrades the sunvnet driver to support VIO protocol version 1.6.
In particular, it adds per-port MTU negotiation, allowing MTUs other than
ETH_FRAMELEN with ports using newer VIO protocol versions.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No caller uses the return value, so make this function return void.
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lowpan_frags_sysctl_register is only called by __init lowpan_net_frag_init
(part of the lowpan module).
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

irlan_open is only called by __init irlan_init in same module.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix:

arch/mips/net/bpf_jit.c: In function 'build_body':
arch/mips/net/bpf_jit.c:762:6: error: unused variable 'tmp'
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/net/bpf_jit.o] Error 1

Seen when building mips:allmodconfig in -next since next-20140924.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
ARM: Berlin: Ethernet support

This series introduce support for the Ethernet controller on Berlin SoCs,
using the existing pxa168 Ethernet driver. In order to do this, DT
support is added to the driver alongside some other modifications and
fixes.

This has been tested on a Berlin BG2Q DMP board.

Changes since v5:
	- fixed the build when building the driver as a module

Changes since v4:
        - removed the phy-addr property and added a phy subnode
        - added COMPILE_TEST for the pxa168_eth driver

Changes since v3:
        - moved the addition of pxa168_eth_get_mac_address() to the patch
          using it first

Changes since v2:
        - reworked how the MAC address is configured
        - made the clock anonymous

Changes since v1:
        - removed custom Berlin Ethernet driver
        - used the pxa168 Ethernet driver instead
        - made modifications to the pxa168 driver (DT support, fixes)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables the Ethernet port on the Marvell Berlin2Q DMP board.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the Ethernet node, enabling the network unit on Berlin
BG2Q SoCs.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a dependency to COMPILE_TEST so that the driver can be compiled for
test purposes.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Berlin SoCs have an Ethernet controller compatible with the pxa168.
Allow these SoCs to use the pxa168_eth driver.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch rework the way the MAC address is retrieved. The MAC address
can now, in addition to being random, be set in the device tree or
retrieved from the Ethernet controller MAC address registers. The
probing function will try to get a MAC address in the following order:
- From the device tree.
- From the Ethernet controller MAC address registers.
- Generate a random one.

This patch also adds a function to read the MAC address from the
Ethernet Controller registers.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing the MAC address, in addition to updating the dev_addr in
the net_device structure, this patch also update the MAC address
registers (high and low) of the Ethernet controller with the new MAC.
The address stored in these registers is used for IEEE 802.3x Ethernet
flow control, which is already enabled.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IEEE 802.3x Ethernet flow control is disabled when bit (1 << 2) is set
in the port status register. Fix the flow control detection in the link
event handling function which was relying on the opposite assumption.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the binding documentation for the Marvell PXA168 Ethernet
controller, following its DT support.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the device tree support to the pxa168_eth driver.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up a bit the pxa168_eth driver before adding the device tree
support.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4_core driver updates

A series from Jack and Co of low-level fixes for the mlx4_core driver
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ConnectX2 HCAs have max_mtu=4k and max_vl=8 vls. However, if you specify
a 4K mtu, the max_vl supported for 4K is 4 vls. The driver at startup
attempts to set a 4K mtu using the max_vl value obtained from QUERY_PORT.

Since the max_vl value is 8 vls (which is supported up to 2K mtu size),
the first attempt to set the mtl/vl port value will fail, generating
the following error message in the log:

  mlx4_core 0000:06:00.0: command 0xc failed: fw status = 0x40

The driver then tries again, using mtu=4k, vls=4, and this succeeds.

Since we do not want to have this error message always displayed at driver
start when there are ConnectX2 HCAs on the host, we deprecate the error
message for this specific command/input_modifier/opcode_modifier/fw-status
to be debug.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function mlx4_QUERY_PORT_wrapper implements only the
QUERY_PORT "general" case (opcode modifier = 0).

Verify that the opcode modifier is zero, and also that the
input modifier contains only the port number in bits 0..7
(all other bits should be zero).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the new flow, we separate the pci initialization and teardown
from the initialization and teardown of the other resources.

__mlx4_init_one handles the pci resources initialization. It then
calls mlx4_load_one to initialize the remainder of the resources.

When removing a device, mlx4_remove_one is invoked. However, now
mlx4_remove_one calls mlx4_unload_one to free all the resources except the pci
resources. When mlx4_unload_one returns, mlx4_remove_one then frees the
pci resources.

The above separation will allow us to implement 'reset flow' in the future.
It will also enable more EQs for VFs and is a pre-step to the modern API to
enable/disable SRIOV.

Also added nvfs; an integer array of size MLX4_MAX_PORTS + 1; to the mlx4_dev
struct. This new field is used to avoid parsing the num_vfs module parameter
each time the mlx4_restart_one is called.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unloading the host driver while there are VFs active on VMs,
the PF driver disabled sriov anyway, causing kernel crashes.

We now leave SRIOV enabled, to avoid that.

When the driver is reloaded, __mlx4_init_one is invoked on the PF.
It now checks to see if SRIOV is already enabled on the PF -- and
if so does not enable sriov again.
Signed-off-by: NTal Alon <talal@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric reports build failure with
CONFIG_BRIDGE_NETFILTER=n

We insist to build br_nf_core.o unconditionally, but we must only do so
if br_netfilter was enabled, else it fails to build due to
functions being defined to empty stubs (and some structure members
being defined out).

Also, BRIDGE_NETFILTER=y|m makes no sense when BRIDGE=n.

Fixes: 34666d46 (netfilter: bridge: move br_netfilter out of the core)
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Markus Pargmann says:

====================
net: cpsw: Support for am335x chip MACIDs

This series adds support to the cpsw driver to read the MACIDs of the am335x
chip and use them as fallback. These addresses are only used if there are no
mac addresses in the devicetree, for example set by a bootloader.
====================
Acked-by: NMugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are 2 MACIDs stored in the control module of the am33xx. These are
read by the cpsw driver if no valid MACID was found in the devicetree.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a function to get the MACIDs from the am33xx SoC
control module registers which hold unique vendor MACIDs. This is only
used if of_get_mac_address() fails to get a valid mac address.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dev_err instead of pr_err.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"MII_BUS_ID_SIZE" is defined in linux/phy.h which is not included in the
cpsw.h file.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ret is set 0 at this point, so jumping to that error label would result
in a return value of 0. Set ret to -ENOMEM to return a proper error
value.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac-address is an optional property. If no mac-address is set, a random
mac-address will be generated.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the code stands today, bonding stats are based simply on the stats
from the member interfaces.  If a member was to be removed from a bond,
the stats would instantly drop.  This would be confusing to an admin
would would suddonly see interface stats drop while traffic is still
flowing.

In addition to preventing the stats drops mentioned above, new members
will now be added to the bond and only traffic received after the member
was added to the bond will be counted as part of bonding stats.  Bonding
counters will also be updated when any slaves are dropped to make sure
the reported stats are reliable.

v2: Changes suggested by Nik to properly allocate/free stats memory.
v3: Properly destroy workqueue and fix netlink configuration path.
v4: Moved cached stats into bonding and slave structs as there does not
seem to be a complexity/performance benefit to using alloc'd memory vs
in-struct memory.
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After previous patches to simplify qstats the qstats can be
made per cpu with a packed union in Qdisc struct.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes the use of qstats->qlen variable from the classifiers
and makes it an explicit argument to gnet_stats_copy_queue().

The qlen represents the qdisc queue length and is packed into
the qstats at the last moment before passnig to user space. By
handling it explicitely we avoid, in the percpu stats case, having
to figure out which per_cpu variable to put it in.

It would probably be best to remove it from qstats completely
but qstats is a user space ABI and can't be broken. A future
patch could make an internal only qstats structure that would
avoid having to allocate an additional u32 variable on the
Qdisc struct. This would make the qstats struct 128bits instead
of 128+32.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds helpers to manipulate qstats logic and replaces locations
that touch the counters directly. This simplifies future patches
to push qstats onto per cpu counters.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to run qdisc's without locking statistics and estimators
need to be handled correctly.

To resolve bstats make the statistics per cpu. And because this is
only needed for qdiscs that are running without locks which is not
the case for most qdiscs in the near future only create percpu
stats when qdiscs set the TCQ_F_CPUSTATS flag.

Next because estimators use the bstats to calculate packets per
second and bytes per second the estimator code paths are updated
to use the per cpu statistics.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new mode of operation to macvlan, called "source".
It allows one to set a list of allowed mac address, which is used
to match against source mac address from received frames on underlying
interface.
This enables creating mac based VLAN associations, instead of standard
port or tag based. The feature is useful to deploy 802.1x mac based
behavior, where drivers of underlying interfaces doesn't allows that.

Configuration is done through the netlink interface using e.g.:
 ip link add link eth0 name macvlan0 type macvlan mode source
 ip link add link eth0 name macvlan1 type macvlan mode source
 ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
 ip link set link dev macvlan0 type macvlan macaddr add 00:22:22:22:22:22
 ip link set link dev macvlan0 type macvlan macaddr add 00:33:33:33:33:33
 ip link set link dev macvlan1 type macvlan macaddr add 00:33:33:33:33:33
 ip link set link dev macvlan1 type macvlan macaddr add 00:44:44:44:44:44

This allows clients with MAC addresses 00:11:11:11:11:11,
00:22:22:22:22:22 to be part of only VLAN associated with macvlan0
interface. Clients with MAC addresses 00:44:44:44:44:44 with only VLAN
associated with macvlan1 interface. And client with MAC address
00:33:33:33:33:33 to be associated with both VLANs.

Based on work of Stefan Gula <steweg@gmail.com>

v8: last version of Stefan Gula for Kernel 3.2.1
v9: rework onto linux-next 2014-03-12 by Michael Braun
    add MACADDR_SET command, enable to configure mac for source mode
    while creating interface
v10:
  - reduce indention level
  - rename source_list to source_entry
  - use aligned 64bit ether address
  - use hash_64 instead of addr[5]
v11:
  - rebase for 3.14 / linux-next 20.04.2014
v12
  - rebase for linux-next 2014-09-25
Signed-off-by: NMichael Braun <michael-dev@fami-braun.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>