iwl_set_rxon_ht() only get called in iwl_post_associate(); which cause
possible incorrect ht configuration. Adding the call in iwl_mac_config() if
IEEE80211_CONF_CHANGE_CHANNEL flag is set to re-configure and send rxon
command.

Fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2146Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On beacon change update notification from mac we are not disabling
the tx in adhoc mode. Mac sends BSS_CHANGED_BEACON_ENABLED when
station leaves IBSS. Driver should indicate uCode to not to send
anything on receiving this notification.

Functionality to indicate uCode is duplicated across
two notifications so created a common function called iwl_set_no_assoc.

Fix the issue at
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2133.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Tested-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To help iwlagn uCode debugging, event log will dump to syslog when driver
detect uCode error occurred, but this only happen when compile with
CONFIG_IWLWIFI_DEBUG and debug flag is enabled; which is not always
the case. Also, there is another problem, if the flag is set, the entire
event log buffer will be dump to syslog, it can flood the syslog and
make it very difficult to debug the problem.

Change the default to only dump last 20 entries of event log to syslog
unless the following condition meets:
1. both compile with CONFIG_IWLWIFI_DEBUG and debug flag
is enabled, and then dump the entire event buffer to syslog.
2. dump event log request from debugfs
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we get a state change of associated or not, we need to tell the
ucode via the RX_ON command using the filter flags.  This will prevent
the ucode from sending any packets when not associated, specifically not
sending NULL QOS packets after a deauthentication which causes the AP to
repeatedly send deauth's in some situations.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

uCode error log contain information as to what the error was and where
it occurred necessary to debug any uCode issues.

Always log the information without special debug flag, this can help to
capture the important information when error happened.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.

Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.

Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LED blinking rate is based on tx/rx traffic, the most reasonable place
to do it is after update the traffic byte counts

This fixes the recent LED blinking breakage on 3945 introduced by "iwlwifi:
separate led function from statistic notification"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CSR_INT_COALESCING previously had only one, but now has two single-byte fields.
With only one single-byte field (lowest order byte) it was okay to write via
iwl_write32(), but now with two, an iwl_write32() to the lower order field
clobbers the other field (odd-address CSR_INT_PERIODIC_REG, offset 0x5), and an
iwl_write32() to CSR_INT_PERIODIC_REG could clobber the lowest byte of the
next-higher register (CSR_INT, offset 0x8).

Fortunately, no bad side effects have been produced by the iwl_write32()
usage, due to order of execution (low order byte was always written before
higher order byte), and the fact that writing "0" to the low byte of the
next higher register has no effect (only action is when writing "1"s).

Nonetheless, this cleans up the accesses so no bad side effects might occur
in the future, if execution order changes, or more bit fields get added to
CSR_INT_COALESCING.

Add some comments regarding periodic interrupt usage.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handle BSS_CHANGED_BEACON_ENABLED to enable the sending
of beacons. Also set the correct HT RXON and QoS config.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending beacon commands to the uCode, we must
inform it of the offset in the beacon frame of the
TIM Element so it can transmit packets from the
correct queue. This functionality is implemented
in iwl_set_beacon_tim().

Fix a bug setting the rate_n_flags for the beacon
packet. First, it should not use the station table's
rate (it's a management frame), and second it needs
to properly configure the TX antennas.

Finally, also, clean up and comment relevant functions.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags

bit 0: Clear statistics
       0: Do not clear Statistics counters
       1: Clear to zero Statistics counters

Allow "clear" parameter to be set from the caller.

Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not use AP's SM_PS setting for our own SM_PS setting.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.

Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To help debug rx related issues, if IWL_DEBUG_RADIO flag is set, print
the rxon configuration when rxon host command send to uCode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.

For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For 6x50 series, it is wimax/wifi combo device, so driver need to enable
the wimax/wifi co-exist function and send the coexist event priority
table to uCode for operation.

The priority table will be used by uCode to determine what is the proper
action it should take when co-exist with WiMAX.
For example, when WiFi runs a scan, it must own radio exclusively, therefore
will disconnect WiMAX if WiMAX is connected.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Spatial Multiplexing Power Save was disabled to achieve better
throughput while in power save mode by activating all the rx chains all the time.
By doing so, the device power consumption is high.

Enable static/dynamic spatial multiplexing power save if device support
it, which can lower the power consumption without impact throughput.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since iwlagn is the only user of these functions, move it to this module.
This results in a bit more code moving than just these functions since the
functions only used by them are also moved and we need to export the
symbols previously available to them directly.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus.
Workaround disables L0S state so device moves directly from L0->L1.
Workaround needed on all devices since and including 4965; add to 6000/1000.

Describe bug and workaround better in comments.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since priv->reg_lock was added to keep multi-access register manipulation
atomic, priv->lock protection is no longer needed.  Remove this from
iwl_apm_stop_master() and iwl_apm_stop().

Add warning of timeout when polling for busmaster disablement confirmation,
and some comments.

NOTE:  This is needed to enable use of apm_ops.stop() within iwl_eeprom_init();
priv->lock does not get initialized until after this flow.  See patch
"remove power-wasting calls to apm_ops.init()"
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support "channel switch" request by issue "channel switch" host command
to uCode.

There is no separated "channel switch" indication from mac80211,
when detected "IEEE80211_CONF_CHANGE_CHANNEL" flag in iwl_mac_config(),
if the station is in "associated" state, then assume "channel switch
announcement" IE was received by mac80211.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using device configuration structure to decide how to configure
ct_kill host command.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding parameter ranges for bt co-exist configuration command.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Consolidate most iwlXXXX_apm_init() functions into single iwl_apm_init().
Keep iwl3945_apm_init(), but leverage iwl_apm_init() for most functionality.
Update 4965 init sequence to follow most recent factory recommendations.

Add following members to struct iwl_cfg to guide the init sequence:
pll_cfg_val (replaces needs_pll_cfg), set_l0s, use_bsm

Move L0S enable/disable from nic_config() functions to iwl_apm_init().
This satisifies the "FIXME: put here L1A -L0S w/a" notice, and complies
with factory-recommended sequence.

Add debug info message in iwl_apm_init(), and symmetrical message
in iwl_apm_stop().
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function is only used in iwlagn so there is no need to have it in
iwlcore.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This switches the iwlwifi driver to use paged skb from linear skb for Rx
buffer. So that it relieves some Rx buffer allocation pressure for the
memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for
Rx buffer. Due to the trailing skb_shared_info in the skb->data,
alloc_skb() will do the next order allocation, which is 16K bytes. This
is suboptimal and more likely to fail when the system is under memory
usage pressure. Switching to paged Rx skb lets us allocate the RXB
directly by alloc_pages(), so that only order 1 allocation is required.

It also adjusts the area spin_lock (with IRQ disabled) protected in the
tasklet because tasklet guarentees to run only on one CPU and the new
unprotected code can be preempted by the IRQ handler. This saves us from
spawning another workqueue to make skb_linearize/__pskb_pull_tail happy
(which cannot be called in hard irq context).

Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb
for all the management frames and software decryption or defragmentation
required data frames before handed to mac80211. For all the other frames,
we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211
to handle them properly.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the ununsed variable data_retry_limit
from priv.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3945 and 4965 share the functionality for setting RTS and CTS to
the tx_cmd. Unify these functions and move the common
functionality to core.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of always allocate the max number of tx queue structure,
use dynamic allocation based on the number of queues in device
configuration. With these changes, device does not have to allocate more
memory than the h/w can support.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

Replace iwl_poll_direct_bit with iwl_poll_bit when accessing CSR registers.
There is no need to power up the mac to access CSR registers.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: NBen M Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.

Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.

At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When instructing the microcode to use just a single
chain when we have power saving enabled, we should
also tell the AP that we are doing SM powersave.
However, using a single chain doesn't actually have
any power saving advantage while idle -- measurements
show that the power consumption is no different when
using one vs. two or three chains.

Therefore, always instruct the microcode to use all
chains.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We never have four chains, but let's fix the typo
while we noticed it. You count 0, 1, 2, 3, not
0, 1, 2, 4 :)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).

Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.

Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).

All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.

For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>