While issuing any ATA passthrough command to firmware the driver will
block the device. But it will unblock the device only if the I/O
completes through the ISR path. If a controller reset occurs before
command completion the device will remain in blocked state.

Make sure we unblock the device following a controller reset if an ATA
passthrough command was queued.

[mkp: clarified patch description]

Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ac6c2a93bd07 ("mpt3sas: Fix for SATA drive in blocked state, after diag reset")
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This is a work around for a bug with LSI Fusion MPT SAS2 when perfoming
secure erase. Due to the very long time the operation takes, commands
issued during the erase will time out and will trigger execution of the
abort hook. Even though the abort hook is called for the specific
command which timed out, this leads to entire device halt
(scsi_state terminated) and premature termination of the secure erase.

Set device state to busy while ATA passthrough commands are in progress.

[mkp: hand applied to 4.9/scsi-fixes, tweaked patch description]
Signed-off-by: NAndrey Grodzovsky <andrey2805@gmail.com>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Trivial fixes, minor spelling mistakes in comments and in a KERN_INFO
message.

[mkp: fixed spelling mistake in patch description]
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use le16_to_cpu only for accessing two byte data provided by controller.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Support Atomic Request Descriptors for Ventura/SAS35 devices.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

An UNMAP command on a PI formatted device will leave the Logical Block
Application Tag and Logical Block Reference Tag as all F's (for those LBAs
that are unmapped). To avoid IO errors if those LBAs are subsequently read
before they are written with valid tag fields, the MPI SCSI IO requests
need to set the EEDPFlags element EEDP Escape Mode field, Bits [7:6]
appropriately. A value of 2 should be set to disable all PI checks if the
Logical Block Application Tag is 0xFFFF for PI types 1 and 2.  A value
of 3 should be set to disable all PI checks if the Logical Block
Application Tag is 0xFFFF and the Logical Block Reference Tag is
0xFFFFFFFF for PI type 3.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For SAS35 devices MSIX vectors are inceased to 128 from 96. To support this
Reply post host index register count is increased to 16. Also variable
msix96_vector is replaced with combined_reply_queue and variable
combined_reply_index_count is added to set different values for SAS3 and
SAS35 devices.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added Device ID's for SAS35 devices (Ventura, Crusader, Harpoon &
Tomcat) and updated mpi header file for the same. Also added
"is_gen35_ioc" to MPT3SAS_ADAPTER structure for identifying SAS35 adapters.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When device missing event arrives, device_remove_in_progress bit will be
set and hence driver has to stop sending IOCTL commands.Now the check has
been added in IOCTL path to test device_remove_in_progress bit is set, if
so then IOCTL will be failed printing failure message.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Return value and Device_handle Arguments passed in correct order
 to match with its format string.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

While merging mpt3sas & mpt2sas code, we added the is_warpdrive check
condition on the wrong line

---------------------------------------------------------------------------
 scsih_target_alloc(struct scsi_target *starget)
                        sas_target_priv_data->handle = raid_device->handle;
                        sas_target_priv_data->sas_address = raid_device->wwid;
                        sas_target_priv_data->flags |= MPT_TARGET_FLAGS_VOLUME;
-                       raid_device->starget = starget;
+                       sas_target_priv_data->raid_device = raid_device;
+                       if (ioc->is_warpdrive)
+                               raid_device->starget = starget;
                }
                spin_unlock_irqrestore(&ioc->raid_device_lock, flags);
                return 0;
------------------------------------------------------------------------------

That check should be for the line sas_target_priv_data->raid_device =
raid_device;

Due to above hunk, we are not initializing raid_device's starget for
raid volumes, and so during raid disk deletion driver is not calling
scsi_remove_target() API as driver observes starget field of
raid_device's structure as NULL.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: 7786ab6a ("mpt3sas: Ported WarpDrive product SSS6200 support")
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In _scsih_io_done() we test if the ioc->logging_level does _not_ have
the MPT_DEBUG_REPLY bit set and if it hasn't we print the debug
messages. This unfortunately is the wrong way around.

Note, the actual bug is older than af009411 but this commit removed the
CONFIG_SCSI_MPT3SAS_LOGGING Kconfig option which hid the bug.

Fixes: af009411 'mpt2sas, mpt3sas: Remove SCSI_MPTXSAS_LOGGING entry from Kconfig'
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Trivial non-functional changes for a couple annoying things:

  1) Functions local to files are not declared static, which is
  frustrating when reading the code because it's non-obvious at first
  glance what's actually called from other files.

  2) Set-but-unused variables abound, presumably to mask -Wunused-result
  errors in the past. None of these are flagged today though (with one
  exception noted below), so remove them.

Fixing (2) exposed the fact that we improperly ignore the return value
of scsi_device_reprobe() in _scsih_reprobe_lun(). Fixing the calling
code to deal with the potential error is non-trivial, so for now just
WARN().
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

With the exception of a single call to wait_for_doorbell_int(), all this
conditional sleeping code is dead. So delete it.
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This flag that conditionally acquires the mutex is confusing and prone
to bugginess: refactor it into two separate function calls, and make the
unlocked one complain if it's called outside the mutex.
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We blindly trust the hardware to give us NUL-terminated strings, which
is a bad idea because it doesn't always do that. For example:

  [  481.184784] mpt3sas_cm0: 	enclosure level(0x0000), connector name(     \x3)

In this case, connector_name is four spaces. We got lucky here because
the 2nd byte beyond our character array happens to be a NUL. Fix this by
explicitly writing '\0' to the end of the string to ensure we don't run
off the edge of the world in printk().
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The _scsih_pci_mmio_enabled called if scsih_pci_error_detected returns
PCI_ERS_RESULT_CAN_RECOVER, at this point, read/write to the device
still works, no need to reset slot.

Or the mpt3sas_base_map_resources in scsih_pci_slot_reset will fail,
and iounamp ioc->chip, then we will meet issue when read ioc->chip
in mpt3sas_base_get_iocstate from _base_fault_reset_work.

Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In _scsih_sas_host_add, the number of HBA phys are determined and then
later used to allocate an array of struct _sas_phy's.  If the routine
sets ioc->sas_hba.num_phys, but then fails to allocate the
ioc->sas_hba.phy array (by kcalloc error or other intermediate
error/exit path), ioc->sas_hba is left in a dangerous state: all readers
of ioc->sas_hba.phy[] do so by indexing it from 0..ioc->sas_hba.num_phys
without checking that the space was ever allocated.

Modify _scsih_sas_host_add to set ioc->sas_hba.num_phys only after
successfully allocating ioc->sas_hba.phy[].
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are some missing curly braces on this if statement, so we end up
printing when we shouldn't.

Fixes: a470a51c ('mpt3sas: Handle active cable exception event')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Set maximum transfer length per IO on RAID volumes to 4MB by setting
VD's queue's max_sector to 8192.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modified driver code to use scsi_prot_ref_tag() API instead of
scsi_get_lba(), while initializing reference tag field in the CDB.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"

This event is only for Intruder/Cutlass HBAs.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member.  The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup".  The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.

Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.

Fixes: 146b16c8 (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Track msix of each IO and use the same msix for issuing abort to timed
out IO. With this driver will process IO's reply first followed by TM.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver assumes HighPriority credit as part of Global credit. But,
Firmware treats HighPriority credit value and global cedits as two
different values. Changed host queue algorithm to treat global credits
and highPriority credits as two different values.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Never block the SEP device (i.e. Never invoke the
scsi_internal_device_block() API for SEP device) even for the delay not
responding events. Blocking the SEP device will create a deadlock while
adding any device to the OS.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1.Wrong size of argument is being passed
 The size of struct being passed as an argument to memset func and area of
 memory being pointed by an instance of struct in memset func should be of
 same structure type.
2.Dereference null return value
3.Array compared against '0'
 Check whether value pointed by particular index of an array is null or not
 in "if" statement.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated hardware description headers with MPI v2.6 and
mpt3sas_pci_table[] with vendor_ids, device_ids of Cutlass and Intruder
HBA which have support for 4 ports.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request
message, check whether TLR is enabled on the drive using
'sas_is_tlr_enabled' API.

Actually in the driver code, driver is using below API's

1. sas_enable_tlr() - to enable the TLR
2. sas_disable_tlr() - to disable the TLR
3. sas_is_tlr_enabled() - to check whether TLR is enabled or not.

but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API,
instead we checking for TLR bit from flag field of driver's 'struct
MPT3SAS_DEVIC' structure. which is corrected with this patch.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.

* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.

* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
  that, during the driver load time driver can use corresponding host
  template(based the pci device ID) while registering a scsi host
  adapter instance for that pci device.

* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
  SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
  processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
  device processes only those ioctl cmds issued for the SAS3 HBAs.

* Added separate indexing for SAS2 and SAS3 HBAs.

* Replaced compile time check 'MPT2SAS_SCSI' to run time check
  'hba_mpi_version_belonged' whereever needed.

* Aliased this merged driver to mpt2sas using MODULE_ALIAS.

* Moved global varaible 'driver_name' to per adapter instance variable.

* Created two raid function template and used corresponding raid
  function templates based on the run time check
  'hba_mpi_version_belonged'.

* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
  renamed it as mpt3sas_warpdrive.c.

* Also renamed the functions in mpt3sas_warpdrive.c file to follow
  current driver function name convention.

* Updated the Makefile to build mpt3sas_warpdrive.o file for these
  WarpDrive-specific functions.

* Also in function mpt3sas_setup_direct_io(), used sector_div() API
  instead of division operator (which gives compilation errors on 32 bit
  machines).

* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.

* Added module parameter 'hbas_to_enumerate' which permits using this
  merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
  driver.

  Here are the available options for this module parameter:

   0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
   1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
   2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs

* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops

1. pci_access_mutex lock added to provide synchronization between IOCTL,
   sysfs, PCI resource handling path

2. gioc_lock spinlock to protect list operations over multiple
   controllers

This patch is ported from commit 6229b414 ("mpt2sas: setpci reset
kernel oops fix").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.

Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.

This patch is ported from commit 008549f6 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.

Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.

This patch is ported from the following mpt2sas driver commit
d224fe0d ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Ported the following list of WarpDrive-specific patches:

1. commit 0bdccdb0 ("mpt2sas: WarpDrive
   New product SSS6200 support added")

2. commit 82a45258 ("mpt2sas: WarpDrive
   Infinite command retries due to wrong scsi command entry in MPI
   message")

3. commit ba96bd0b ("mpt2sas: Support
   for greater than 2TB capacity WarpDrive")

4. commit 4da7af94 ("mpt2sas: Do not
   retry a timed out direct IO for Warpdrive")

5. commit daeaa9df ("mpt2sas: Avoid type
   casting for direct I/O commands").

Also set the mpt2_ioctl_iocinfo adapter_type to:

1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs

2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive

3. MPT2_IOCTL_INTERFACE_SAS2  for other Gen2 HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Do not enable MSI-X vectors for SAS2008 B0 controllers

2. Enable a single MSI-X vector for the following controller:

   a. SAS2004
   b. SAS2008
   c. SAS2008_1
   d. SAS2008_2
   e. SAS2008_3
   f. SAS2116_1
   g. SAS2116_2

3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for Gen3 Invader/Fury C0 and above revision HBAs

4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for all Intruder and Cutlass HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers
since they don't support it.

Also enable fast_path only for SAS3 HBAs.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently there is a logging level option provided for each of our
drivers in the kernel configuration utility. Users can enable this
option to get more verbose information. By default it is enabled.

Only when this option is enabled will the functions which display the
required information get compiled in.

As we are merging the both drivers we can no longer provide this
configuration option. Remove the SCSI_MPTXSAS_LOGGING entry from Kconfig
and unconditionally enable logging (by removing the #ifdef
CONFIG_SCSI_MPT3SAS_LOGGING preprocessor check conditions) so that all
functions which are defined to display more verbose information get
compiled in.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each
individual generation driver functionality at runtime.

2. Declare global variable 'driver_name' and use this variable while
reserving PCI regions and while allocating the IRQs.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Created a mpt3sas_module.c file for mpt3sas driver where it can register
SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the
corresponding interfaces from mpt3sas_scsih.c file.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>