There is QE on platform T104x, add support.
Call funcs qe_ic_init and qe_init if CONFIG_QUICC_ENGINE is defined.
Signed-off-by: NZhao Qiang <B45475@freescale.com>
[scottwood@freesacle.com: whitespace fix]
Signed-off-by: NScott Wood <scottwood@freescale.com>

New QE doesn't have par_io, it doesn't need to init par_io
for new QE.
Split function mpc85xx_qe_init() into mpc85xx_qe_init()
and mpc85xx_qe_par_io_init().
Call mpc85xx_qe_init() for both new and old while
mpc85xx_qe_par_io_init() after mpc85xx_qe_init() for old.
Signed-off-by: NZhao Qiang <B45475@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

If CONFIG_UCC_GETH or CONFIG_SERIAL_QE is not defined then we get a
warning about an used variable which leads to a build error.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NScott Wood <scottwood@freescale.com>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

The one instance where we add an include for init.h covers off
a case where that file was implicitly getting it from another
header which itself didn't need it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

TWR-P1025 Overview
 -----------------
 512Mbyte DDR3 (on board DDR)
 64MB Nor Flash
 eTSEC1: Connected to RGMII PHY AR8035
 eTSEC3: Connected to RGMII PHY AR8035
 Two USB2.0 Type A
 One microSD Card slot
 One mini-PCIe slot
 One mini-USB TypeB dual UART
Signed-off-by: NMichael Johnston <michael.johnston@freescale.com>
Signed-off-by: NXie Xiaobo <X.Xie@freescale.com>
[scottwood@freescale.com: use pr_info rather than KERN_INFO]
Signed-off-by: NScott Wood <scottwood@freescale.com>

Define a QE init function in common file, and avoid
the same codes being duplicated in board files.
Signed-off-by: NXie Xiaobo <X.Xie@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

It makes no sense to initialize the mpic ipi for the SoC which has
doorbell support. So set the smp_85xx_ops.probe to NULL for this
case. Since the smp_85xx_ops.probe is also used in function
smp_85xx_setup_cpu() to check if we need to invoke
mpic_setup_this_cpu(), we introduce a new setup_cpu function
smp_85xx_basic_setup() to remove this dependency.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Commit b5b4bb3f (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org

The P1010RDB-PB is similar to P1010RDB(P1010RDB-PA).
So, P1010RDB-PB use the same platform file as P1010RDB.
Then Add support for P1010RDB-PB platform.
Signed-off-by: NZhao Qiang <B45475@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Currently all these boards use the same machine struct and also select
the same kernel options, so it seems a bit of redundant to keep one
separate kernel option for each board. Also update the defconfigs
according to this change.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

This file is also used by some RDB and QDS boards. So the name seems
not so accurate. Rename it to corenet_generic.c. Also update the
function names in this file according to the change.
Signed-off-by: NKevin Hao <haokexin@gmail.com>

In the current kernel, the board files for p2041rdb, p3041ds, p4080ds,
p5020ds, p5040ds, t4240qds and b4qds are almost the same except the
machine name. So this introduces a cornet_generic machine to support
all these boards to avoid the code duplication.

With these changes the file corenet_ds.h becomes useless. Just delete
it.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Commit 9837b43c ("powerpc/85xx: enable
coreint for all the 64bit boards") removed the ifdef that avoided
coreint on 64-bit, but it missed b4_qds.c.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: Shaveta Leekha <shaveta@freescale.com>

When removing prom.h include by of.h, several OF headers will no longer
be implicitly included. Add explicit includes of of_*.h as needed.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@linaro.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: linuxppc-dev@lists.ozlabs.org

C293PCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module.

 - 512KB platform SRAM in addition to 512K L2 Cache/SRAM
 - 512MB soldered DDR3 32bit memory
 - CPLD System Logic
 - 64MB x16 NOR flash and 4GB x8 NAND flash
 - 16MB SPI flash
Signed-off-by: NMingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: NPo Liu <Po.Liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

P1023RDB Specification:
-----------------------
Memory subsystem:
   512MB DDR3 (Fixed DDR on board)
   64MB NOR flash
   128MB NAND flash

Ethernet:
   eTSEC1: Connected to Atheros AR8035 GETH PHY
   eTSEC2: Connected to Atheros AR8035 GETH PHY

PCIe:
   Three mini-PCIe slots

USB:
   Two USB2.0 Type A ports

I2C:
   AT24C08 8K Board EEPROM (8 bit address)
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Some CPUs (such as e500v1/v2) don't implement mftb and will take a
trap.  mfspr should work on everything that has a timebase, and is the
preferred instruction according to ISA v2.06.

Currently we get away with mftb on 85xx because the assembler converts
it to mfspr due to -Wa,-me500.  However, that flag has other effects
that are undesireable for certain targets (e.g.  lwsync is converted to
sync), and is hostile to multiplatform kernels.  Thus we would like to
stop setting it for all e500-family builds.

mftb/mftbu instances which are in 85xx code or common code are
converted.  Instances which will never run on 85xx are left alone.
Signed-off-by: NScott Wood <scottwood@freescale.com>

Erratum A-006598 says that 64-bit mftb is not atomic -- it's subject
to a similar race condition as doing mftbu/mftbl on 32-bit.  The lower
half of timebase is updated before the upper half; thus, we can share
the workaround for a similar bug on Cell.  This workaround involves
looping if the lower half of timebase is zero, thus avoiding the need
for a scratch register (other than CR0).  This workaround must be
avoided when the timebase is frozen, such as during the timebase sync
code.

This deals with kernel and vdso accesses, but other userspace accesses
will of course need to be fixed elsewhere.
Signed-off-by: NScott Wood <scottwood@freescale.com>

T4, Cell, powernv, and pseries had the same implementation, so switch
them to use a generic version. A2 apparently had a version, but
removed it at some point, so we remove the declaration, too.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The function pci_devs_phb_init is invoked more earlier than we really
probe the pci controller, so it does nothing at all. And we also don't
need the pci_dn stuff for the fsl powerpc64 boards, just remove it.

It also seems that we don't support ISA on all the current corenet ds
boards. So picking a primary bus seems useless, remove that function
too.
Signed-off-by: NKevin Hao <haokexin@gmail.com>

The p1020rdb-pd has the similar feature as the p1020rdb.
Therefore, p1020rdb-pd use the same platform file as the p1/p2 rdb board.
Overview of P1020RDB-PD platform:
- DDR3 2GB
- NOR flash 64MB
- NAND flash 128MB
- SPI flash 16MB
- I2C EEPROM 256Kb
	- eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch
	- eTSEC2 (SGMII PHY)
- eTSEC3 (RGMII PHY)
	- SDHC
	- 2 USB ports
	- 4 TDM ports
	- PCIe
Signed-off-by: NHaijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

With the patch 7230c564 (powerpc: Rework lazy-interrupt handling),
it seems that the coreint works pretty well on the 85xx 64bit kernel.
So use the coreint by default for these boards.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications.  For example, the fix in
commit 5e427ec2 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.

After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out.  Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.

This removes all the powerpc uses of the __cpuinit macros.  There
are no __CPUINIT users in assembly files in powerpc.

[1] https://lkml.org/lkml/2013/5/20/589

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

- Add support for B4 board in board file b4_qds.c,
  It is common for B4860, B4420 and B4220QDS as they share same QDS board
- Add B4QDS support in Kconfig and Makefile

B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor,
with following major features:

    - Four dual-threaded e6500 Power Architecture processors
      organized in one cluster-each core runs up to 1.8 GHz
    - Two DDR3/3L controllers for high-speed memory interface each
      runs at up to 1866.67 MHz
    - CoreNet fabric that fully supports coherency using MESI protocol
      between the e6500 cores, SC3900 FVP cores, memories and
      external interfaces.
    - Data Path Acceleration Architecture having FMAN, QMan, BMan,
      SEC 5.3 and RMAN
    - Large internal cache memory with snooping and stashing capabilities
    - Sixteen 10-GHz SerDes lanes that serve:
        - Two SRIO interfaces. Each supports up to 4 lanes and
          a total of up to 8 lanes
        - Up to 8-lanes Common Public Radio Interface (CPRI) controller
          for glue-less antenna connection
        - Two 10-Gbit Ethernet controllers (10GEC)
        - Six 1G/2.5-Gbit Ethernet controllers for network communications
        - PCI Express controller
        - Debug (Aurora)
    - Various system peripherals

B4420 and B4220 have some differences in comparison to B4860 with fewer
core/clusters(both SC3900 and e6500), fewer DDR controllers,
fewer serdes lanes, fewer SGMII interfaces and reduced target frequencies.

Key differences between B4860 and B4420:
B4420 has:
    - Fewer e6500 cores:
        1 cluster with 2 e6500 cores
    - Fewer SC3900 cores/clusters:
        1 cluster with 2 SC3900 cores per cluster
    - Single DDRC @ 1.6GHz
    - 2 X 4 lane serdes
    - 3 SGMII interfaces
    - no sRIO
    - no 10G

Key differences between B4860 and B4220:
B4220 has:
    - Fewer e6500 cores:
        1 cluster with 1 e6500 core
    - Fewer SC3900 cores/clusters:
        1 cluster with 2 SC3900 cores per cluster
    - Single DDRC @ 1.33GHz
    - 2 X 2 lane serdes
    - 2 SGMII interfaces
    - no sRIO
    - no 10G
Signed-off-by: NShaveta Leekha <shaveta@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

mpic_reset_core() need a logical cpu number instead of physical.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Somehow the driver snuck in with these still in it.
Signed-off-by: NBen Collins <ben.c@servergy.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO, so there is no need to select
it explicitly.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Somehow the driver snuck in with these still in it.
Signed-off-by: NBen Collins <ben.c@servergy.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some minor changes to the common corenet_ds.c code are needed to support
the T4240QDS:
* Add support for "fsl,qoriq-pcie-v3.0" controller
* Bump max # of IRQs to 512 (T4240 supports more interrupts than
  previous SoCs).
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPIC code will disable coreint if it detects an insufficient
MPIC version.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Initial board support for the Prodrive PPA8548 AMC module. Board
is an MPC8548 AMC platform used in RapidIO systems. This module is
also used to test/work on mainline linux RapidIO software.

PPA8548 overview:
- 1.3 GHz Freescale PowerQUICC III MPC8548 processor
- 1 GB DDR2 @ 266 MHz
- 8 MB NOR flash
- Serial RapidIO 1.2
- 1 x 10/100/1000 BASE-T front ethernet
- 1 x 1000 BASE-BX ethernet on AMC connector
Signed-off-by: NStef van Os <stef.van.os@prodrive.nl>
Acked-by: NTimur Tabi <timur@tabi.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Freescale DIU driver was recently updated to not require every DIU
platform function, so now we can remove the unneeded functions from
some boards.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Delete successive tests to the same location.  The code tested the result
of a previous call, that itself was already tested.  It is changed to test
the result of the most recent call.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@

*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
    when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

CTS-1000 is based on P4080. GPIO 27 is used to signal the FPGA to
switch off power, and also associates IRQ 8 with front-panel button
press (which we use to call orderly_poweroff()).

The relevant device-tree looks like this:

	gpio0: gpio@130000 {
		compatible = "fsl,qoriq-gpio";
		reg = <0x130000 0x1000>;
		interrupts = <55 2 0 0>;
		#gpio-cells = <2>;
		gpio-controller;

		/* Allows powering off the system via GPIO signal. */
		gpio-halt@27 {
			compatible = "sgy,gpio-halt";
			gpios = <&gpio0 27 0>;
			interrupts = <8 1 0 0>;
		};
	};

Because the driver cannot match on sgy,gpio-halt (because the node is never
processed through of_platform), it matches on fsl,qoriq-gpio and then
checks child nodes for the matching sgy,gpio-halt. This also ensures that
the GPIO controller is detected prior to sgy_cts1000's probe callback,
since that node wont match via of_platform until the controller is
registered.

Also, because the GPIO handler for triggering system poweroff might sleep,
the IRQ uses a workqueue to call orderly_poweroff().

As a final note, this driver may be expanded for other features specific to
the CTS-1000.
Signed-off-by: NBen Collins <ben.c@servergy.com>
Cc: Jack Smith <jack.s@servergy.com>
Cc: Vihar Rai <vihar.r@servergy.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.

CC: Kumar Gala <galak@kernel.crashing.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NTim Blechmann <tim@klingt.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ePAPR v1.1 requires the spin table to be in cached memory. So we need
to change the call argument of ioremap to enable cache and coherence.
We also flush the cache after writing to spin table to keep it compatible
with previous cache-inhibit spin table. Flushing before and after
accessing spin table is recommended by ePAPR.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>