Miscellaneous Fixes:
- Fix a couple of sparse complaints
- Reset the FCP recovery flag when the node is not a FCP2 device.
- Speed up offline prep delays
- Fixed a memory leak in lpfc_mem_alloc failure path
- Fixed external loopback test.
- Fixed error code returned from the driver when HBA is over heated.
- Correct Max NPIV vport to limits read from adapter
- Add missing locks around fc_flag and FC_NEEDS_REG_VPI
- Add missing hba ids for device identification
- Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands
- Changed all temperature event messages from warning to error
- Fix reporting of link speed when link is down
- Added support for MBX_WRITE_WWN mailbox command
- Change del_timer_sync() in ISR to del_timer() in interrupt handler
- Correct instances of beXX_to_cpu() that should be cpu_to_beXX()
- Perform target flush before releasing node references on module unload
- Avoid bogus devloss_tmo messages when driver unloads
- Fix panic when HBA generates ERATT interupt
- Fix mbox race condition and a workaround on back-to-back mailbox commands
- Force NPIV off for pt2pt mode between 2 NPorts
- Stop worker thread before removing fc_host.
- Fix up discovery timeout error case due to missing clear_la
- Tighten mailbox polling code to speed up detection of fast completions
- Only allow DUMP_MEMORY if adapter offline due to overtemp errors
- Added extended error information to the log messages in chip init.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Add parameters to enable and disable heartbeat and hba resets
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Correct Abort handler logic. It was unconditionally waiting a minimum
of 2 seconds rather than looking for abort completion.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Miscellaneous Discovery/ELS Fixes:
- Delay free's of ELS requests if adapter reject conditions
- Fix concurrent PLOGI vs ADISC state handling
- Add retry mechanism for GFF_ID
- Correct some illegal state transitions around RSCN timeouts
- Fix missing return in FAN handling
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The adapter queue is divided up equally to all the arrays to prevent
command starvation to any individual array. On the other hand,
physical targets are only granted a queue depth of one each. The code
prior to this patch used to deal with the incremental discovery of
targets, but the driver knows how many arrays are present prior to the
scan so this knowledge is used to generate a better estimate for the
queue depth.

Remove the capability of 'physical=0' from preventing access to the
class of adapters that have the RAID/SCSI mode of operation since none
of the physicals on the SCSI channel are candidates ever for an array.

As always, the user can override this default queue depth policy by
making the appropriate adjustments utilizing sysfs.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

In experiments in the lab we managed to trigger an Adapter firmware
panic (BlinkLED) coincidentally while several pass-through ioctl
command from the management software were outstanding on a bug only
present on a class of RAID Adapters that require a hardware reset
rather than a commanded reset. The net result was an attempt to time
out the management software command as if it came from the SCSI layer
resulting in an OS panic.

Adapters that use commanded reset, management commands are returned
failed by the Adapter correctly. The adapter firmware panic that
resulted in this condition was also resolved, and there were no
adapters in the field with this specific firmware bug so we do not
expect any field reports. This is a rare or unlikely corner condition,
and no reports have ever been forwarded from the field.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The 'entry' automatic variable was defined at the top and within a
block that uses it, removed the definition from the block that uses
it. Some cosmetic changes were made while in the same file. This patch
should be inert.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Big endian systems issues discovered in the aacraid driver. Somewhat
reverses a patch from November 7th of last year that removed swap
operations because they formerly were being assigned to an u8 array
when they should have been assigned to an le32 array.

This patch is largely inert for any little endian processor
architecture. It resolves a bug in delivering the BlinkLED AIF event
to registered applications when the adapter or associated hardware was
reset due to ill health. A rare corner case occurrence, also largely
unnoticed by any as it was a new (untested!) feature.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The parameter 'info' is reused, renamed the second to sinfo to
represent supplemental adapter info, to suppress compile warning
message.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Report the RAID level string for the SCSI device representing the
array. Report is in /sys/class/scsi_device/#:#:#:#/device/level.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

aacraid.cache parameter, Disable Queue Flush commands:
        bit 0 - Disable FUA in WRITE SCSI commands
        bit 1 - Disable SYNCHRONIZE_CACHE SCSI command
        bit 2 - Disable only if Battery not protecting adapter supplied Cache

e.g.: aacraid.cache=7 will disable the FUA and SYNCHRONIZE_CACHE
commands if the adapter has reported that it's cache is battery backed
up.

This parameter permits experimentation with tradeoffs between
performance and caching policy.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This conversion makes full use of the is_visible() callback on attribute
groups.  Now, each device appears only with its capability flags in the
transport class directory.  Previously each device appeared with the
capability of the host, so this is a functionality improvement.
Converting to attribute groups allows us to sweep away most of the home
grown #defines that were effectively doing the same thing.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch allows the various users of attribute_groups to selectively
allow the appearance of group attributes.  The primary consumer of
this will be the transport classes in which we currently have
elaborate attribute selection algorithms to do this same thing.
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

While trying to convert the SPI transport class to attribute groups, I
discovered that we don't actually have any transport configure points
for either the target or the host.  This patch adds these missing
transport class triggers.  The host one is simply done after the add,
the target one tries to be more clever and add it after devices may have
been placed on the target (so the device configure will have set up the
target parameters).
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch is the beginning of moving the attribute_containers to use
attribute groups exclusively.  The attr element is now deprecated and
will eventually be removed (along with all the hand rolled code for
doing exactly what attribute groups do) when all the consumers are
converted to attribute groups.
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

I can't see a reason why these shouldn't work on every group.  However,
they only seem to work on named groups.  This patch allows the group
functions to work on anonymous groups (those with NULL names).
Acked-by: NTejun Heo <htejun@gmail.com>
Acked-by: NKay Sievers <kay.sievers@vrfy.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Hugh Dickens noticed that SMART commands issued from user space can
end up corupting memory.  The problem occurs if the buffer used to
read data spans two pages.  The reason is that the PIO sector routines
in libata are expecting physically contiguous pages when they do
sector operations, so the left overs on the second page go into the
next physically adjacent page rather than the next page in the sg
mapping.

Fix this by enforcing strict 512 byte alignment on all buffers from
userspace.
Acked-by: NHugh Dickins <hugh@veritas.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes.  I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.

The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev.  (basically all inquiries it
issues can now be directly mapped).
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The purpose of this is to allow stacked alignment settings, with the
ultimate queue alignment being set to the largest alignment requirement
in the stack.

The reason for this is so that the SCSI mid-layer can relax the default
alignment requirements (which are basically causing a lot of superfluous
copying to go on in the SG_IO interface) while allowing transports,
devices or HBAs to add stricter limits if they need them.
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Looks like that host_cmd_pool_mutex are necessary here.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Based on an original patch from: David Martin <tasio@tasio.net>

When trying to get the drive status via ioctl CDROM_DRIVE_STATUS, with
no disk it gives CDS_TRAY_OPEN even if the tray is closed.

ioctl works as expected with ide-cd driver.

Gentoo bug report: http://bugs.gentoo.org/show_bug.cgi?id=196879

Cc: Maarten Bressers <mbres@gentoo.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This is bad for two reasons:

     1. If they're returned to outside applications, no-one knows what
        they mean.
     2. Eventually they'll clash with the ever expanding standard error
        codes.

The problem error code in question is ETASK.  I've replaced this by
ECOMM (communications error on send) a network error code that seems to
most closely relay what ETASK meant.
Acked-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Currently in BSG, errors returned in req->errors aren't passed back to
the calling programme (either via SG_IO or via read/write).  Fix this,
while preserving the SCSI convention of returning status in
req->errors.

Now update libsas to return errors correctly instead of to ignore
them.
Acked-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

All SMP tasks sent through bsg generate messages like:

sas: smp_execute_task: task to dev 500605b000001450 response: 0x0 status 0x81

Three times (because the task gets retried).  Firstly, don't retry
either overrun or underrun (the data buffer isn't going to change size)
and secondly, just report the underrun but don't set an error for it.
This is necessary so bsg can report back the residual.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This adds support for host side SMP processing, via a separate
SMP interpreter file.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch fixes mptsas_smp_handler to update both din_resid or
dout_resid on success. bsg can report back the residual.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the task management command, i.e whether we can issue this
request for this unit/port. If the error recovery is about to close this
unit/port, then it competes for the queue-lock. If the close request issued by
the error recovery wins, then it is guaranteed that this unit/port has been
blocked for other requests.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Peschke <mp3@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the FCP command, i.e whether we can issue this request for
this unit/port. If the error recovery is about to close this unit/port, then it
competes for the queue-lock. If the close request issued by the error recovery
wins, then it is guaranteed that this unit/port has been blocked for other
requests.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Peschke <mp3@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We need to hold the queue-lock when checking whether we still have a valid port
handle for the ELS command, i.e whether we can issue this request for this
port. If the error recovery is about to close this port, then it competes for
the queue-lock. If the close request issued by the error recovery wins, then it
is guaranteed that this port has been blocked for other requests.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Peschke <mp3@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the abort command, i.e whether we can issue this request
for this unit/port. If the error recovery is about to close this unit/port,
then it competes for the queue-lock. If the close request issued by the error
recovery wins, then it is guaranteed that this unit/port has been blocked for
other requests.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Peschke <mp3@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

According to the FSF spec, word 0 (bytes 0-3) has the handle
specified with the abort command and word 1 (bytes 4-7) has the
handle for the command to be aborted. Fix the if statements
that try to compare those.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Peschke <mp3@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

zfcp_erp_strategy_check_fsfreq() checks if it is safe to access the
fsf_req associated with the erp_action that gets passed. To test if
it is safe it accesses the fsf_req in order to get its index into
the hash list. This is broken since the fsf_req might be freed already
and the read index has no meaning. It could lead to memory corruption.
Fix this by introducing a new zfcp_reqlist_find_safe() method which
just checks if addresses are equal. This is slower, but only gets
called in case of error recovery.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Peschke <mp3@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

megaraid_remove_one() can become __devexit.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: N"Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

SR_REQ is defined 0x20, but bitanding has no effect because '!' has a higher
priority than '&'
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

we are planning a major rewrite of the zfcp driver,
meaning that a lot of patches will hit the mailing-list in the near future.

Since I can't support this additional work-load along with my other
responsibilities we are shifting the maintainership to
Christof Schmitt as the maintainer and
Martin Peschke as the co-maintainer.

Please support the two in providing us a new and more stable
zfcp environment.

Thanks
Swen
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Update version.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If we negotiate for X r2ts we have to use only X r2ts. We cannot
round up (we could send less though). It is ok to fail if it
is not something the driver can handle, so this patch just does
that.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: Nvignesh babu <vignesh.babu@wipro.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

iscsi_data_rsp needs to hold the sesison lock when it calls
iscsi_update_cmdsn.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The previous patches converted iscsi_tcp to support sg chaining.
This patch sets the proper flags and sets sg_table size to
4096. This allows fs io to be capped at max_sectors, but passthrough
IO to be limited by some other part of the kernel.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>