Remove fault-armv.o, mmap.o and mm-armv.o from uclinux builds - these
are concerned with MMU-ful operations, and as such are redundant for
uclinux.

Since this also removes iotable_init() and iotable_init() is used
extensively in the platform support files, just make it a no-op.

Based upon a couple of patches by Hyok.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

nommu doesn't require a complex flush_dcache_page implementation
like the MMU-ful CPUs do, so provide a simplified version in nommu.c
and omit flush.c from the build as appropriate.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

nommu doesn't have any form of remapping support, so ioremap, etc
become stubs which just return the casted address, doing nothing
else.

Move ioport_map(), ioport_unmap(), pci_iomap(), pci_iounmap()
into a separate file which is always built.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

This patch adds support for the new XScale v3 core.  This is an
ARMv5 ISA core with the following additions:

- L2 cache
- I/O coherency support (on select chipsets)
- Low-Locality Reference cache attributes (replaces mini-cache)
- Supersections (v6 compatible)
- 36-bit addressing (v6 compatible)
- Single instruction cache line clean/invalidate
- LRU cache replacement (vs round-robin)

I attempted to merge the XSC3 support into proc-xscale.S, but XSC3
cores have separate errata and have to handle things like L2, so it
is simpler to keep it separate.

L2 cache support is currently a build option because the L2 enable
bit must be set before we enable the MMU and there is no easy way to
capture command line parameters at this point.

There are still optimizations that can be done such as using LLR for
copypage (in theory using the exisiting mini-cache code) but those
can be addressed down the road.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Daniel Jacobowitz

After delivering a signal (creating its stack frame) we must check for
additional pending unblocked signals before returning to userspace.
Otherwise signals may be delayed past the next syscall or reschedule.

Once that was fixed it became obvious that the ARM signal mask manipulation
was broken.  It was a little bit broken before the recent SA_NODEFER
changes, and then very broken after them.  We must block the requested
signals before starting the handler or the same signal can be delivered
again before the handler even gets a chance to run.
Signed-off-by: NDaniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM copypage changes in 2.6.12-rc4-git1 removed the preempt locking
from the copypage functions which broke the XScale implementation.
This patch fixes the locking on XScale and removes the now unneeded
minicache code.
Signed-off-by: NRussell King <rmk@arm.linux.org.uk>
Checked-by: Richard Purdie

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!