The QID_MGMT is assigned to the beacon and atim queue
during initialization. This means we don't need a seperate
check in write_tx_desc()..
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework the interface handling. Delete the interface structure
and replace it with a per-interface structure. This changes the
way rt2x00 handles the active interface drastically.

Copy ieee80211_bss_conf to the this rt2x00_intf structure during
the bss_info_changed() callback function. This will allow us to
reference it later, and removes the requirement for the device flag
SHORT_PREAMBLE flag which is interface specific.

Drivers receive the option to give the maximum number of virtual
interfaces the device can handle. Virtual interface support:
rt2400pci: 1 sta or 1 ap, * monitor interfaces
rt2500pci: 1 sta or 1 ap, * monitor interfaces
rt2500usb: 1 sta or 1 ap, * monitor interfaces
rt61pci: 1 sta or 4 ap, * monitor interfaces
rt73usb: 1 sta or 4 ap, * monitor interfaces

At the moment none of the drivers support AP and STA interfaces
simultaneously, this is a hardware limitation so future support
will be very unlikely.

Each interface structure receives its dedicated beacon entry,
with this we can easily work with beaconing while multiple master
mode interfaces are currently active.

The configuration handlers for the MAC, BSSID and type are
often called together since they all belong to the interface
configuration. Merge the 3 configuration calls and cleanup
the API between rt2x00lib and the drivers. While we are cleaning
up the interface configuration anyway, we might as well clean up
the configuration handler as well.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver should select what CRC algorithm is required
when performing a checksum on the firmware.

rt61pci & rt73usb require crc-itu-t
rt2800pci & rt2800usb require crc-ccitt

Legacy 2800pci/usb driver uses crc-itu-t + bit order reversion,
but that is just inefficient especially since the end result is
the same as a different algorithm which is also available as library. ;)
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This introduces a big queue handling overhaul, this also
renames "ring" to "queues".

Move queue handling into rt2x00queue.c and the matching header,
use Kerneldoc to improve rt2x00 library documentation.

Access to the queues is now protected under a spinlock, this
to prevent race conditions which could corrupt the indexing
system of the queue.

Each queue entry allocates x bytes for driver/device specific data,
this cleans up the queue structure significantly and improves
code readability.

rt2500usb no longer needs 2 entries in the beacon queue to correctly
send out the guardian byte. This is now handled in the entry specific
structure.

rt61 and rt73 now use the correct descriptor size for beacon frames,
since this data is written into the registers not the entire TXD
descriptor was used but instead of a subset of it named TXINFO.

Finally this also fixes numerous other bugs related to incorrect
beacon handling or beacon related code.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.

Reorder the things that should be done during a
link tuner reset and during a link tuner start.

Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.

Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix 2 issues in antenna diversity selection.

1) the following statement will always return true.
	if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.

2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For TX rings the queue_idx should start at
IEEE80211_TX_QUEUE_DATA0 and for each followup
ring this index needs to be increased.

For the RX ring the queue_idx should be set
to 0. We don't need to initialize the tx_params.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.

This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.

This new BSS configuration infrastructure adds the following
new features:
 * drivers are notified of their association AID
 * drivers are notified of association status

and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prior to enabling the radio rt2x00lib should go through all
rings and for each entry should call the callback function
init_txentry() and init_rxentry().
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the MY_BSS descriptor field to determine if the
received frame belongs to the same BSS as the interface.
This can be used by rxdone to determine if the frame
should be updated or not.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Send the skb structure with write_tx_desc() and use
the skbdesc structure to read all information about
the frame. This saves several arguments in the function
definition and it is easier to send more information
later as well.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The packet filter flags don't belong in the interface structure
because they are device based instead of interface based.
So move the filter fields out of struct interface and into rt2x00_dev.

Additionally we shouldn't change the filter based on the working
mode, if such a thing is needed than mac80211 should have done that.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

suspend & resume was broken since it called rt2x00mac_start()
and rt2x00mac_stop() which would fail to execute because the
DEVICE_PRESENT flag was not set.

Move the start and stop handlers into rt2x00lib.c which are called
from rt2x00mac_start() and rt2x00mac_stop() after they have checked
the DEVICE_PRESENT flag, while suspend and resume handlers can
directly call those functions.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Store the queue idx inside structure data_ring
Store the entry idx inside structure data_entry
This saves us a few calls to ARRAY_INDEX() which is now unused.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restrict rssi average updating to beacon frames of the bssid the
interface is
associated with. Without this restriction, strong signals belonging to other
BSS, e.g. beacon frames coming from a nearby AP, would cause incorrectly high
rssi approximation values. This would then cause the link tuner to reduce
sensitivity, resulting in transmissions from the BSS associated to to be
missed.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to use a seperate define INVALID_INTERFACE while
we can use IEEE80211_IF_TYPE_INVALID directly.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds TX/RX frame dumping capabilities through debugfs.
The intention is that with this approach debugging of rt2x00 is
simplified since _all_ frames going in and out of the device
are send to debugfs as well along with additional information
like the hardware descriptor.

Based on the patch by Mattias Nissler.
Mattias also has some tools that will make the dumped frames
available to wireshark: http://www-user.rhrk.uni-kl.de/~nissler/rt2x00/Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the skb->cb field to add a frame description that can be used
to transfer information passed each rt2x00 layer. This reduces the
required arguments for rt2x00lib_write_tx_desc().
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DRV_NAME was always set to the KBUILD_MODNAME value,
lets clean everything up by removing DRV_NAME and just
use KBUILD_MODNAME directly.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a flag to struct txdata_entry_desc that specifies whether an ack for the
frame is to be expected. Use this flag to set the ACK bit in the tx descriptor.
Previously, the ACK bit could be set incorrectly on CTS-to-self frames, so they
caused retries and were reported to be failed in the txdone handlers.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coverty indicated that data_desc with a single
element array is bad coding style. This removes
the structure and forces everybody to use __le32.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mac80211 indicates that the default antenna setup
should be used _and_ that this default setup is SW_DIVERSITY.

This requires sampling and storing the RSSI per antenna
and check once every 2 seconds to determine if the RSSI
has changed significantly. Once this is the case we should sample
the other antenna for a short period and evaluate if
we need to swap antenna or not.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rt2x00_clear_link() was becoming too large for statically inline,
also it was used on a single location and shouldn't really be
used anywhere else. So move the entire code into the function
rt2x00lib_start_link_tuner()
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac80211 has 3 values for the antenna setup:
 0 - default
 1 - use antenna 1
 2 - use antenna 2

This means that rt2x00 should store the default value
from the EEPROM somwhere and use that when mac80211 indicates
that the antenna setup is 0.
This also implies that rt2x00 should no longer write the
hw->config.antenna_sel_* values based on the EEPROM input.

This also adds the basis in rt2x00lib for correct software
diversity handling. By default rt2x00lib will now configure
antenna B instead of hardware diversity.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all link quality statistics variables into
the link_qual structure. This cleans up the link
structure and allows us to use it for more then
just statistics.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because rt2x00 implements the residual calculation different from what the
legacy code does (i.e. scaled values), we need to adjust the residual check.
Again, we are only mimicking the behaviour of the ralink driver without
actually knowing what we do :-(
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reorganize configuration handling by creating a extra
structure which contains precalculated values based
on the mac80211 values which are usefull for all
individual drivers.

This also fixes the preamble configuration problem,
up untill now preamble was never configured since
by default the rate->val value was used when changing
the mode.
Now rate->val will only be used to set the basic rate mask.
The preamble configuration will now be done correctly
through the erp_ie_changed callback function.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Directly pass a value from the enum dev_state with rt2x00lib_toggle_rx,
this will save us a ? : statement, and it is clearer then passing a 1 0
argument.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As reported by Modestas Vainius, enabling rkfill in 1 driver and
disabling it in a second could cause a NULL pointer exception when
the rfkill-disabled driver still sets the CONFIG_SUPPORT_HW_BUTTON flag.

Furthermore, rfkill expects the timeout as a value in milliseconds
instead of jiffies. Also increase the timeout to a second,
since this 250ms would be overkill.

Also the flag DEVICE_ENABLED_RADIO_HW is causing problems
for devices which do not support the hardware button
while rfkill is enabled in the driver.

To remidy this we should inverse the flag and its meaning,
rename the flag to DEVICE_DISABLED_RADIO_HW this means that
by default the radio is enabled by the hardware button (if present)
and can only be disabled explicitely.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We shouldn't use changed_flags when configuring the packet filter,
we work directly with the total_flags which is safe enough since
we already check if something has changed after we applied our
packet filtering flag rules.
Also make sure that when the packet filter is scheduled, the
rt2x00dev->interface.filter is cleared to make sure the drivers
will update the packet filter instead of failing at the check:
*total_flags == rt2x00dev->interface.filter
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Store the started state into a new flag DEVICE_STARTED_SUSPEND
and set this when suspending while the device was started.
We can't check for is_interface_present() since only mac80211
knows if there are monitor interfaces present.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't check if the radio is enabled in rt2x00lib_toggle_rx,
this is required since the link tuner should be disabled
when shutting down the device. The remaining calls inside the
rt2x00lib_toggle_rx handler should deliver no problems when
called while the radio is done.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When ieee80211_hw.config indicates that the radio
is enabled and is configuring options that require
the link tuner to be restarted the link tuner will
cause a kernel panic when rfkill has indicated the
radio was in fact disabled.
Signed-off-by: NModestas Vainius <modestas@vainius.eu>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As pointed out by Modestas Vainius the link tuner
could continue working while the radio is already
down. This because at the start of disable_radio
the ENABLED_RADIO flag is cleared and causes the
toggle_rx to skip the stop_link_tuner() call.
This will add a check to the start of the link tuner
which will automatically stop the link tuner when the
radio is disabled.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calling cancel_delayed_work_sync() unconditionally won't hurt
and it will avoid race conditions when another CPU is already
executing link_tuner work.
Signed-off-by: NModestas Vainius <modestas@vainius.eu>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rt2x00dev->flags has become a chaos over time,
this will reorganize the flags by renaming, deleting, adding
and properly implement the flags.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The call to rt2x00lib_precalculate_link_signal resets link.rx_success
which is needed when calculating the average rssi for the link
tuner. Change the call order so the link tuner runs first as it
doesn't need the result of the precalculate.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.

This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.

Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.

At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().

The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.

Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>