Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Turns out ath5k and ath9k can share the same helper to
allocates RX skbs. We allocate skbs aligned to the cache line
size. This requirement seems to have come from AR5210; when
this was not done it seems sometimes we'd get bogus data. I'm
also told it may have been a performance enhancement
consideration. In the end I can't be sure we can remove this
on new hardware so just keep this and start sharing it through
ath.ko.

Make ath9k start using this, ath5k is next.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We re-label the device driver initialization routines from the
ath_softc, the "Software Carrier" fillers. This should make it
clearer what each of these do.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Location: ath9k/phy#/xmit
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a small window where the mac80211 changes the IEEE80211_CONF_PS
flag, and then informs the driver about the change. We have a race
condition if we are checking the flag in the same time. Avoid it by
introducing a local variable, and using that instead of checking the
IEEE80211_CONF_PS flag directly.

This fix the problem reported by Luis:
http://article.gmane.org/gmane.linux.kernel.wireless.general/34363

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup aggregation start/stop function interfaces.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These can be obtained from mac80211.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This uses the new configuration changes indicated up by
mac80211 when all interfaces are marked idle. We need to do
a little more work as we have our own set of virtual
wiphys within ath9k.

Only when all virtual wiphys are inactive do we allow an idle
state change for a wiphy to trigger disabling the radio.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These functions are changing the power mode of the chip, but this may
have unpredictable effects, if another code are trying to set the power
mode via 'ath9k_hw_setpower' in the same time from another context.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Uninline these functions before we add functional changes to them.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because ath9k_setpower is called from various contexts, we have to
protect it against concurrent calls.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hardware doesn't generate interrupts in some cases and so work
around this by monitoring the TX status periodically and reset the
chip if required.

This behavior of the hardware not generating the TX interrupts can
be noticed through ath9k debugfs interrupt statistics when heavy
traffic is being sent from STA to AP. One can easily see this behavior
when the STA is transmitting at a higher rates. The interrupt statistics
in the debugfs interface clearly shows that only RX interrupts alone
being generated and TX being stuck.

TX should be monitored through a timer and reset the chip only when
frames are queued to the hardware but TX interrupts are not generated
for the same even after one second. Also, we shouldn't remove holding
descriptor from AC queue if it happens to be the only descriptor and
schedule TX aggregation regarless of queue depth as it improves
scheduling of AMPDUs from software to hardware queue.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RSSI reported by the RX descriptor requires little manipulation.
Manipulate and report the correct RSSI to the stack. This will
fix the improper signal levels reported by iwconfig iw dev wlanX
station dump. Also the Link Quality reported seems to be varying
(falls to zero also sometimes) when iperf is run from STA to AP.

Also use the default noise floor for now as the one reported
during the caliberation seems to be wrong.

The Signal and Link Quality before this patch (taken while TX is
in progress from STA to AP)

09:59:13.285428037 Link Quality=29/70  Signal level=-81 dBm
09:59:13.410660084 Link Quality=20/70  Signal level=-90 dBm
09:59:13.586864392 Link Quality=21/70  Signal level=-89 dBm
09:59:13.710296281 Link Quality=21/70  Signal level=-89 dBm
09:59:13.821683064 Link Quality=25/70  Signal level=-85 dBm
09:59:13.933402989 Link Quality=24/70  Signal level=-86 dBm
09:59:14.045839276 Link Quality=26/70  Signal level=-84 dBm
09:59:14.193926673 Link Quality=23/70  Signal level=-87 dBm
09:59:14.306230262 Link Quality=31/70  Signal level=-79 dBm
09:59:14.419459667 Link Quality=26/70  Signal level=-84 dBm
09:59:14.530711167 Link Quality=37/70  Signal level=-73 dBm
09:59:14.642593962 Link Quality=29/70  Signal level=-81 dBm
09:59:14.754361169 Link Quality=21/70  Signal level=-89 dBm
09:59:14.866217355 Link Quality=21/70  Signal level=-89 dBm
09:59:14.976963623 Link Quality=28/70  Signal level=-82 dBm
09:59:15.089149809 Link Quality=26/70  Signal level=-84 dBm
09:59:15.205039887 Link Quality=27/70  Signal level=-83 dBm
09:59:15.316368003 Link Quality=23/70  Signal level=-87 dBm
09:59:15.427684036 Link Quality=36/70  Signal level=-74 dBm
09:59:15.539756380 Link Quality=21/70  Signal level=-89 dBm
09:59:15.650549093 Link Quality=22/70  Signal level=-88 dBm
09:59:15.761171672 Link Quality=32/70  Signal level=-78 dBm
09:59:15.872793750 Link Quality=23/70  Signal level=-87 dBm
09:59:15.984421694 Link Quality=22/70  Signal level=-88 dBm
09:59:16.097315093 Link Quality=21/70  Signal level=-89 dBm

The link quality and signal level after this patch (take while
TX is in progress from STA to AP)

17:21:25.627848091 Link Quality=65/70  Signal level=-45 dBm
17:21:25.762805607 Link Quality=65/70  Signal level=-45 dBm
17:21:25.875521888 Link Quality=66/70  Signal level=-44 dBm
17:21:25.987468448 Link Quality=66/70  Signal level=-44 dBm
17:21:26.100628151 Link Quality=66/70  Signal level=-44 dBm
17:21:26.213129671 Link Quality=66/70  Signal level=-44 dBm
17:21:26.324923070 Link Quality=65/70  Signal level=-45 dBm
17:21:26.436831357 Link Quality=65/70  Signal level=-45 dBm
17:21:26.610356973 Link Quality=65/70  Signal level=-45 dBm
17:21:26.723340047 Link Quality=65/70  Signal level=-45 dBm
17:21:26.835715293 Link Quality=64/70  Signal level=-46 dBm
17:21:26.949542748 Link Quality=64/70  Signal level=-46 dBm
17:21:27.062261613 Link Quality=65/70  Signal level=-45 dBm
17:21:27.174511563 Link Quality=64/70  Signal level=-46 dBm
17:21:27.287616232 Link Quality=64/70  Signal level=-46 dBm
17:21:27.400598119 Link Quality=64/70  Signal level=-46 dBm
17:21:27.511381404 Link Quality=64/70  Signal level=-46 dBm
17:21:27.624530421 Link Quality=65/70  Signal level=-45 dBm
17:21:27.737807109 Link Quality=64/70  Signal level=-46 dBm
17:21:27.850861352 Link Quality=65/70  Signal level=-45 dBm
17:21:27.963369436 Link Quality=64/70  Signal level=-46 dBm
17:21:28.076582289 Link Quality=64/70  Signal level=-46 dBm
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This has no functional change and just cleans up the code
to be more legible and removes a useless variable for
Multi Rate Retry.

For regular frames we use 2 retries for MRR segments [0-2].
For the last MRR segment [3] we use 4.

MRR[0] = 2
MRR[1] = 2
MRR[2] = 2
MRR[3] = 4

Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ANI calibration shouldn't be done when we are not on our home channel.
This is already verified. However, it is racy. Fix this by proper
spin locks.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 already has one to keep track of number of failure
addba attempts.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have to remain awake if the SC_OP_WAIT_FOR_CAB flag is set.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This ports the ath9k rfkill code to the new API offered by
cfg80211 and thus removes a lot of useless stuff.

("With this series a kernel panic, which is a regression, during module
unload disappears." -- Vasanthakumar Thiagarajan <vasanth@atheros.com>

Other patches in the series:

  ath9k: Add helper to get ath9k specific current channel
  ath9k: Make sure we have current channel in ah_curchan before rf
    disable/enable

-- JWL)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Luis Rodriguez <mcgrof@gmail.com>
Tested-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch completely rewrites the rfkill core to address
the following deficiencies:

 * all rfkill drivers need to implement polling where necessary
   rather than having one central implementation

 * updating the rfkill state cannot be done from arbitrary
   contexts, forcing drivers to use schedule_work and requiring
   lots of code

 * rfkill drivers need to keep track of soft/hard blocked
   internally -- the core should do this

 * the rfkill API has many unexpected quirks, for example being
   asymmetric wrt. alloc/free and register/unregister

 * rfkill can call back into a driver from within a function the
   driver called -- this is prone to deadlocks and generally
   should be avoided

 * rfkill-input pointlessly is a separate module

 * drivers need to #ifdef rfkill functions (unless they want to
   depend on or select RFKILL) -- rfkill should provide inlines
   that do nothing if it isn't compiled in

 * the rfkill structure is not opaque -- drivers need to initialise
   it correctly (lots of sanity checking code required) -- instead
   force drivers to pass the right variables to rfkill_alloc()

 * the documentation is hard to read because it always assumes the
   reader is completely clueless and contains way TOO MANY CAPS

 * the rfkill code needlessly uses a lot of locks and atomic
   operations in locked sections

 * fix LED trigger to actually change the LED when the radio state
   changes -- this wasn't done before
Tested-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some APs seem to drift away from the expected TBTT (timestamp %
beacon_int_in_usec differs quite a bit from zero) which can result in
us waking up way too early to receive a Beacon frame. In order to work
around this, re-configure the Beacon timers after having received a
Beacon frame from the AP (i.e., when we know the offset between the
expected TBTT and the actual time the AP is sending out the Beacon
frame).
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using timeout=0 (PS-Poll) with mac80211, the driver will need to
wake up for TX requests and remain awake until the TX has been
completed (ACK received or timeout) or until the buffer frame(s) have
been received (in case the TX is for a PS-Poll frame).
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch configures the beacon timers with beacon interval
and beacon period passed through vif.bss_conf. Also cache the
currecnt beacon configuration which will be used to configure
the beacon timers when the driver triggers it after reset.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The previous implementation was moving back to NETWORK SLEEP state
immediately after receiving a Beacon frame. This means that we are
unlikely to receive all the buffered broadcast/multicast frames that
would be sent after DTIM Beacon frames. Fix this by parsing the Beacon
frame and remaining awake, if needed, to receive the buffered
broadcast/multicast frames. The last buffered frame will trigger the
move back into NETWORK SLEEP state.

If the last broadcast/multicast frame is not received properly (or if
the AP fails to send it), the next Beacon frame will work as a backup
trigger for returning into NETWORK SLEEP.

A new debug type, PS (debug=0x800 module parameter), is added to make
it easier to debug potential power save issues in the
future. Currently, this is only used for the Beacon frame and buffered
broadcast/multicast receiving.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On x86 this allows us to do the following small savings:
shave off 23 % off of the module's data, and
shave off 6  % off of the module's text.

We save 456 bytes, for those counting.

$ size ath9k.ko
   text    data     bss     dec     hex filename
 250794    3628    1600  256022   3e816 ath9k.ko
$ size ath9k-old.ko
   text    data     bss     dec     hex filename
 239114   15308    1600  256022   3e816 ath9k-old.ko

$ du -b ath9k.ko
4034244 ath9k.ko
$ du -b ath9k-old.ko
4033788 ath9k-old.ko
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The spin_lock handling uses lots of instructions on some archs.
With this patch the size of the ath9k module will be significantly
smaller.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.

This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.

NOTE: The hw.conf.beacon_int setting is retained for now due
      to drivers still using it -- I couldn't untangle all
      drivers, some are updated in this patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are unnecessary constructs in a function.
This patch removes these from both RX and TX init
routines.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We never handle TIM, TIM_TIMER is used instead.
Remove this and the unnecessary swBeaconProcess variable.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

struct aggr_rifs_param and ath_tx_stat are not used anywhere.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using a u32 to store a single flag is overkill.
Use a bool to store whether the buffer is stale or not.
Also, use u8 instead of u32 to store the buffer type.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change the void pointer to struct sk_buff and access
bf_mpdu directly, removing all casts in the process.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unused HW capability flags and
HW operation variables, and a chainmask flag that
we don't use anywhere.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

How time flies.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the TSF offset calculation for staggered Beacon frames
and sets ATH_BCBUF back to the earlier value 4 to enable multi-BSS
configurations of up to four BSSes.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All 802.11n PCI devices (Cardbus, PCI, mini-PCI) require
serialization of IO when on non-uniprocessor systems. PCI
express devices not not require this.

This should fix our only last standing open ath9k kernel.org
bugzilla bug report:

http://bugzilla.kernel.org/show_bug.cgi?id=12110

A port is probably required to older kernels and I can work on
that.

Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>