Conflicts:
	drivers/hid/hid-core.c

Merge branches 'for-3.11/battery', 'for-3.11/elo', 'for-3.11/holtek' and 'for-3.11/i2c-hid-fixed' into for-linus

The current i2c hid driver does not support sending HID output reports using
the output register for devices which support receiving reports through this
method. This patch determines which method to use to send output reports based
 on the value of wMaxOutputLength in the device's HID descriptor.
Signed-off-by: NAndrew Duggan <aduggan@synaptics.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Genius Gila Gaming Mouse presents an obviously wrong report descriptor.
the Consumer control (report ID 3) is the following:
0x05, 0x0c,                    // Usage Page (Consumer Devices)       105
0x09, 0x01,                    // Usage (Consumer Control)            107
0xa1, 0x01,                    // Collection (Application)            109
0x85, 0x03,                    //   Report ID (3)                     111
0x19, 0x00,                    //   Usage Minimum (0)                 113
0x2a, 0xff, 0x7f,              //   Usage Maximum (32767)             115
0x15, 0x00,                    //   Logical Minimum (0)               118
0x26, 0xff, 0x7f,              //   Logical Maximum (32767)           120
0x75, 0x10,                    //   Report Size (16)                  123
0x95, 0x03,                    //   Report Count (3)                  125
0x81, 0x00,                    //   Input (Data,Arr,Abs)              127
0x75, 0x08,                    //   Report Size (8)                   129
0x95, 0x01,                    //   Report Count (1)                  131
0x81, 0x01,                    //   Input (Cnst,Arr,Abs)              133
0xc0,                          // End Collection                      135

So the first input whithin this report has a count of 3 but a usage range
of 32768. So this value is obviously wrong as it should not be greater than
the report count.

Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=959721Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Extend the comment explaining the condition for discarding
out-of-range values to clarify the cases in which devices don't
provide any logical min/max.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit 6da70669 introduced in 3.3
"HID: ignore absolute values which don't fit between logical min and max"
prevents some Posiflex touch screen to work because they do not provide
logical min and max for their buttons.
Thus, logical min and max are at 0, discarding the buttons events, and
preventing the device to report appropriate X Y.

Adding a check on "min < max" solves the problem.
Reported-by: NJan Kandziora <jjj@gmx.de>
Tested-by: NJan Kandziora <jjj@gmx.de>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Return value of cdev_add in hid_roccat.c init was not checked.
Signed-off-by: NMichael Rissi <michael.rissi@dectris.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Let's follow the structure we are trying to keep for most of the
specific HID drivers, and let the separation follow the producing
vendor.
Merge functionality provided by ps3remote driver into hid-sony.
Tested-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Pull networking update from David Miller:

 1) Fix dump iterator in nfnl_acct_dump() and ctnl_timeout_dump() to
    dump all objects properly, from Pablo Neira Ayuso.

 2) xt_TCPMSS must use the default MSS of 536 when no MSS TCP option is
    present.  Fix from Phil Oester.

 3) qdisc_get_rtab() looks for an existing matching rate table and uses
    that instead of creating a new one.  However, it's key matching is
    incomplete, it fails to check to make sure the ->data[] array is
    identical too.  Fix from Eric Dumazet.

 4) ip_vs_dest_entry isn't fully initialized before copying back to
    userspace, fix from Dan Carpenter.

 5) Fix ubuf reference counting regression in vhost_net, from Jason
    Wang.

 6) When sock_diag dumps a socket filter back to userspace, we have to
    translate it out of the kernel's internal representation first.
    From Nicolas Dichtel.

 7) davinci_mdio holds a spinlock while calling pm_runtime, which
    sleeps.  Fix from Sebastian Siewior.

 8) Timeout check in sh_eth_check_reset is off by one, from Sergei
    Shtylyov.

 9) If sctp socket init fails, we can NULL deref during cleanup.  Fix
    from Daniel Borkmann.

10) netlink_mmap() does not propagate errors properly, from Patrick
    McHardy.

11) Disable powersave and use minstrel by default in ath9k.  From Sujith
    Manoharan.

12) Fix a regression in that SOCK_ZEROCOPY is not set on tuntap sockets
    which prevents vhost from being able to use zerocopy.  From Jason
    Wang.

13) Fix race between port lookup and TX path in team driver, from Jiri
    Pirko.

14) Missing length checks in bluetooth L2CAP packet parsing, from Johan
    Hedberg.

15) rtlwifi fails to connect to networking using any encryption method
    other than WPA2.  Fix from Larry Finger.

16) Fix iwlegacy build due to incorrect CONFIG_* ifdeffing for power
    management stuff.  From Yijing Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
  b43: stop format string leaking into error msgs
  ath9k: Use minstrel rate control by default
  Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity"
  ath9k: Disable PowerSave by default
  net: wireless: iwlegacy: fix build error for il_pm_ops
  rtlwifi: Fix a false leak indication for PCI devices
  wl12xx/wl18xx: scan all 5ghz channels
  wl12xx: increase minimum singlerole firmware version required
  wl12xx: fix minimum required firmware version for wl127x multirole
  rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks
  mwifiex: debugfs: Fix out of bounds array access
  Bluetooth: Fix mgmt handling of power on failures
  Bluetooth: Fix missing length checks for L2CAP signalling PDUs
  Bluetooth: btmrvl: support Marvell Bluetooth device SD8897
  Bluetooth: Fix checks for LE support on LE-only controllers
  team: fix checks in team_get_first_port_txable_rcu()
  team: move add to port list before port enablement
  team: check return value of team_get_port_by_index_rcu() for NULL
  tuntap: set SOCK_ZEROCOPY flag during open
  netlink: fix error propagation in netlink_mmap()
  ...

Pull input layer bugfix from Jiri Kosina:
 "Memory leak regression fix from Benjamin Tissoires"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: multitouch: prevent memleak with the allocated name

Pull block layer fixes from Jens Axboe:
 "Outside of bcache (which really isn't super big), these are all
  few-liners.  There are a few important fixes in here:

   - Fix blk pm sleeping when holding the queue lock

   - A small collection of bcache fixes that have been done and tested
     since bcache was included in this merge window.

   - A fix for a raid5 regression introduced with the bio changes.

   - Two important fixes for mtip32xx, fixing an oops and potential data
     corruption (or hang) due to wrong bio iteration on stacked devices."

* 'for-linus' of git://git.kernel.dk/linux-block:
  scatterlist: sg_set_buf() argument must be in linear mapping
  raid5: Initialize bi_vcnt
  pktcdvd: silence static checker warning
  block: remove refs to XD disks from documentation
  blkpm: avoid sleep when holding queue lock
  mtip32xx: Correctly handle bio->bi_idx != 0 conditions
  mtip32xx: Fix NULL pointer dereference during module unload
  bcache: Fix error handling in init code
  bcache: clarify free/available/unused space
  bcache: drop "select CLOSURES"
  bcache: Fix incompatible pointer type warning

Merge misc fixes from Andrew Morton:
 "Bunch of fixes and one little addition to math64.h"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
  include/linux/math64.h: add div64_ul()
  mm: memcontrol: fix lockless reclaim hierarchy iterator
  frontswap: fix incorrect zeroing and allocation size for frontswap_map
  kernel/audit_tree.c:audit_add_tree_rule(): protect `rule' from kill_rules()
  mm: migration: add migrate_entry_wait_huge()
  ocfs2: add missing lockres put in dlm_mig_lockres_handler
  mm/page_alloc.c: fix watermark check in __zone_watermark_ok()
  drivers/misc/sgi-gru/grufile.c: fix info leak in gru_get_config_info()
  aio: fix io_destroy() regression by using call_rcu()
  rtc-at91rm9200: use shadow IMR on at91sam9x5
  rtc-at91rm9200: add shadow interrupt mask
  rtc-at91rm9200: refactor interrupt-register handling
  rtc-at91rm9200: add configuration support
  rtc-at91rm9200: add match-table compile guard
  fs/ocfs2/namei.c: remove unecessary ERROR when removing non-empty directory
  swap: avoid read_swap_cache_async() race to deadlock while waiting on discard I/O completion
  drivers/rtc/rtc-twl.c: fix missing device_init_wakeup() when booted with device tree
  cciss: fix broken mutex usage in ioctl
  audit: wait_for_auditd() should use TASK_UNINTERRUPTIBLE
  drivers/rtc/rtc-cmos.c: fix accidentally enabling rtc channel
  ...

There is div64_long() to handle the s64/long division, but no mocro do
u64/ul division.  It is necessary in some scenarios, so add this
function.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The lockless reclaim hierarchy iterator currently has a misplaced
barrier that can lead to use-after-free crashes.

The reclaim hierarchy iterator consist of a sequence count and a
position pointer that are read and written locklessly, with memory
barriers enforcing ordering.

The write side sets the position pointer first, then updates the
sequence count to "publish" the new position.  Likewise, the read side
must read the sequence count first, then the position.  If the sequence
count is up to date, it's guaranteed that the position is up to date as
well:

  writer:                         reader:
  iter->position = position       if iter->sequence == expected:
  smp_wmb()                           smp_rmb()
  iter->sequence = sequence           position = iter->position

However, the read side barrier is currently misplaced, which can lead to
dereferencing stale position pointers that no longer point to valid
memory.  Fix this.
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Reported-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NTejun Heo <tj@kernel.org>
Acked-by: NMichal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: <stable@kernel.org>		[3.10+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The bitmap accessed by bitops must have enough size to hold the required
numbers of bits rounded up to a multiple of BITS_PER_LONG.  And the
bitmap must not be zeroed by memset() if the number of bits cleared is
not a multiple of BITS_PER_LONG.

This fixes incorrect zeroing and allocation size for frontswap_map.  The
incorrect zeroing part doesn't cause any problem because frontswap_map
is freed just after zeroing.  But the wrongly calculated allocation size
may cause the problem.

For 32bit systems, the allocation size of frontswap_map is about twice
as large as required size.  For 64bit systems, the allocation size is
smaller than requeired if the number of bits is not a multiple of
BITS_PER_LONG.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

audit_add_tree_rule() must set 'rule->tree = NULL;' firstly, to protect
the rule itself freed in kill_rules().

The reason is when it is killed, the 'rule' itself may have already
released, we should not access it.  one example: we add a rule to an
inode, just at the same time the other task is deleting this inode.

The work flow for adding a rule:

    audit_receive() -> (need audit_cmd_mutex lock)
      audit_receive_skb() ->
        audit_receive_msg() ->
          audit_receive_filter() ->
            audit_add_rule() ->
              audit_add_tree_rule() -> (need audit_filter_mutex lock)
                ...
                unlock audit_filter_mutex
                get_tree()
                ...
                iterate_mounts() -> (iterate all related inodes)
                  tag_mount() ->
                    tag_trunk() ->
                      create_trunk() -> (assume it is 1st rule)
                        fsnotify_add_mark() ->
                          fsnotify_add_inode_mark() ->  (add mark to inode->i_fsnotify_marks)
                        ...
                        get_tree(); (each inode will get one)
                ...
                lock audit_filter_mutex

The work flow for deleting an inode:

    __destroy_inode() ->
     fsnotify_inode_delete() ->
       __fsnotify_inode_delete() ->
        fsnotify_clear_marks_by_inode() ->  (get mark from inode->i_fsnotify_marks)
          fsnotify_destroy_mark() ->
           fsnotify_destroy_mark_locked() ->
             audit_tree_freeing_mark() ->
               evict_chunk() ->
                 ...
                 tree->goner = 1
                 ...
                 kill_rules() ->   (assume current->audit_context == NULL)
                   call_rcu() ->   (rule->tree != NULL)
                     audit_free_rule_rcu() ->
                       audit_free_rule()
                 ...
                 audit_schedule_prune() ->  (assume current->audit_context == NULL)
                   kthread_run() ->    (need audit_cmd_mutex and audit_filter_mutex lock)
                     prune_one() ->    (delete it from prue_list)
                       put_tree(); (match the original get_tree above)
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When we have a page fault for the address which is backed by a hugepage
under migration, the kernel can't wait correctly and do busy looping on
hugepage fault until the migration finishes.  As a result, users who try
to kick hugepage migration (via soft offlining, for example) occasionally
experience long delay or soft lockup.

This is because pte_offset_map_lock() can't get a correct migration entry
or a correct page table lock for hugepage.  This patch introduces
migration_entry_wait_huge() to solve this.
Signed-off-by: NNaoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NWanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: NMichal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>	[2.6.35+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

dlm_mig_lockres_handler() is missing a dlm_lockres_put() on an error path.
Signed-off-by: Njoyce <xuejiufei@huawei.com>
Reviewed-by: Nshencanquan <shencanquan@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The watermark check consists of two sub-checks.  The first one is:

	if (free_pages <= min + lowmem_reserve)
		return false;

The check assures that there is minimal amount of RAM in the zone.  If
CMA is used then the free_pages is reduced by the number of free pages
in CMA prior to the over-mentioned check.

	if (!(alloc_flags & ALLOC_CMA))
		free_pages -= zone_page_state(z, NR_FREE_CMA_PAGES);

This prevents the zone from being drained from pages available for
non-movable allocations.

The second check prevents the zone from getting too fragmented.

	for (o = 0; o < order; o++) {
		free_pages -= z->free_area[o].nr_free << o;
		min >>= 1;
		if (free_pages <= min)
			return false;
	}

The field z->free_area[o].nr_free is equal to the number of free pages
including free CMA pages.  Therefore the CMA pages are subtracted twice.
This may cause a false positive fail of __zone_watermark_ok() if the CMA
area gets strongly fragmented.  In such a case there are many 0-order
free pages located in CMA.  Those pages are subtracted twice therefore
they will quickly drain free_pages during the check against
fragmentation.  The test fails even though there are many free non-cma
pages in the zone.

This patch fixes this issue by subtracting CMA pages only for a purpose of
(free_pages <= min + lowmem_reserve) check.

Laura said:

  We were observing allocation failures of higher order pages (order 5 =
  128K typically) under tight memory conditions resulting in driver
  failure.  The output from the page allocation failure showed plenty of
  free pages of the appropriate order/type/zone and mostly CMA pages in
  the lower orders.

  For full disclosure, we still observed some page allocation failures
  even after applying the patch but the number was drastically reduced and
  those failures were attributed to fragmentation/other system issues.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Tested-by: NLaura Abbott <lauraa@codeaurora.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NMinchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>	[3.7+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The "info.fill" array isn't initialized so it can leak uninitialized stack
information to user space.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NRobin Holt <holt@sgi.com>
Acked-by: NDimitri Sivanich <sivanich@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was a regression introduced by 36f55889 ("aio: refcounting
cleanup"), reported by Jens Axboe - the refcounting cleanup switched to
using RCU in the shutdown path, but the synchronize_rcu() was done in
the context of the io_destroy() syscall greatly increasing the time it
could block.

This patch switches it to call_rcu() and makes shutdown asynchronous
(more asynchronous than it was originally; before the refcount changes
io_destroy() would still wait on pending kiocbs).

Note that there's a global quota on the max outstanding kiocbs, and that
quota must be manipulated synchronously; otherwise io_setup() could
return -EAGAIN when there isn't quota available, and userspace won't
have any way of waiting until shutdown of the old kioctxs has finished
(besides busy looping).

So we release our quota before kioctx shutdown has finished, which
should be fine since the quota never corresponded to anything real
anyways.
Signed-off-by: NKent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: NJens Axboe <axboe@kernel.dk>
Tested-by: NJens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Tested-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the at91sam9x5-family which must use the shadow
interrupt mask due to a hardware issue (causing RTC_IMR to always be
zero).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add shadow interrupt-mask register which can be used on SoCs where the
actual hardware register is broken.

Note that some care needs to be taken to make sure the shadow mask
corresponds to the actual hardware state.  The added overhead is not an
issue for the non-broken SoCs due to the relatively infrequent
interrupt-mask updates.  We do, however, only use the shadow mask value
as a fall-back when it actually needed as there is still a theoretical
possibility that the mask is incorrect (see the code for details).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add accessors for the interrupt register.

This will allow us to easily add a shadow interrupt-mask register to use
on SoCs where the interrupt-mask register cannot be used.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add configuration support which can be used to implement SoC-specific
workarounds for broken hardware.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The members of Atmel's at91sam9x5 family (9x5) have a broken RTC
interrupt mask register (AT91_RTC_IMR).  It does not reflect enabled
interrupts but instead always returns zero.

The kernel's rtc-at91rm9200 driver handles the RTC for the 9x5 family.
Currently when the date/time is set, an interrupt is generated and this
driver neglects to handle the interrupt.  The kernel complains about the
un-handled interrupt and disables it henceforth.  This not only breaks
the RTC function, but since that interrupt is shared (Atmel's SYS
interrupt) then other things break as well (e.g.  the debug port no
longer accepts characters).

Tested on the at91sam9g25.  Bug confirmed by Atmel.

This patch (of 5):

Add missing match-table compile guard.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While removing a non-empty directory, the kernel dumps a message:

  (rmdir,21743,1):ocfs2_unlink:953 ERROR: status = -39

Suppress the error message from being printed in the dmesg so users
don't panic.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: NSunil Mushran <sunil.mushran@gmail.com>
Reviewed-by: NJie Liu <jeff.liu@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

read_swap_cache_async() can race against get_swap_page(), and stumble
across a SWAP_HAS_CACHE entry in the swap map whose page wasn't brought
into the swapcache yet.

This transient swap_map state is expected to be transitory, but the
actual placement of discard at scan_swap_map() inserts a wait for I/O
completion thus making the thread at read_swap_cache_async() to loop
around its -EEXIST case, while the other end at get_swap_page() is
scheduled away at scan_swap_map().  This can leave the system deadlocked
if the I/O completion happens to be waiting on the CPU waitqueue where
read_swap_cache_async() is busy looping and !CONFIG_PREEMPT.

This patch introduces a cond_resched() call to make the aforementioned
read_swap_cache_async() busy loop condition to bail out when necessary,
thus avoiding the subtle race window.
Signed-off-by: NRafael Aquini <aquini@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Acked-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When booted in legacy mode device_init_wakeup() gets called by
drivers/mfd/twl-core.c when the children are initialized.  However, when
booted using device tree, the children are created with
of_platform_populate() instead add_children().

This means that the RTC driver will not have device_init_wakeup() set,
and we need to call it from the driver probe like RTC drivers typically
do.

Without this we cannot test PM wake-up events on omaps for cases where
there may not be any physical wake-up event.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Reported-by: NKevin Hilman <khilman@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If a new logical drive is added and the CCISS_REGNEWD ioctl is invoked
(as is normal with the Array Configuration Utility) the process will
hang as below.  It attempts to acquire the same mutex twice, once in
do_ioctl() and once in cciss_unlocked_open().  The BKL was recursive,
the mutex isn't.

  Linux version 3.10.0-rc2 (scameron@localhost.localdomain) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Fri May 24 14:32:12 CDT 2013
  [...]
  acu             D 0000000000000001     0  3246   3191 0x00000080
  Call Trace:
    schedule+0x29/0x70
    schedule_preempt_disabled+0xe/0x10
    __mutex_lock_slowpath+0x17b/0x220
    mutex_lock+0x2b/0x50
    cciss_unlocked_open+0x2f/0x110 [cciss]
    __blkdev_get+0xd3/0x470
    blkdev_get+0x5c/0x1e0
    register_disk+0x182/0x1a0
    add_disk+0x17c/0x310
    cciss_add_disk+0x13a/0x170 [cciss]
    cciss_update_drive_info+0x39b/0x480 [cciss]
    rebuild_lun_table+0x258/0x370 [cciss]
    cciss_ioctl+0x34f/0x470 [cciss]
    do_ioctl+0x49/0x70 [cciss]
    __blkdev_driver_ioctl+0x28/0x30
    blkdev_ioctl+0x200/0x7b0
    block_ioctl+0x3c/0x40
    do_vfs_ioctl+0x89/0x350
    SyS_ioctl+0xa1/0xb0
    system_call_fastpath+0x16/0x1b

This mutex usage was added into the ioctl path when the big kernel lock
was removed.  As it turns out, these paths are all thread safe anyway
(or can easily be made so) and we don't want ioctl() to be single
threaded in any case.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mike Miller <mike.miller@hp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

audit_log_start() does wait_for_auditd() in a loop until
audit_backlog_wait_time passes or audit_skb_queue has a room.

If signal_pending() is true this becomes a busy-wait loop, schedule() in
TASK_INTERRUPTIBLE won't block.

Thanks to Guy for fully investigating and explaining the problem.

(akpm: that'll cause the system to lock up on a non-preemptible
uniprocessor kernel)

(Guy: "Our customer was in fact running a uniprocessor machine, and they
reported a system hang.")
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Reported-by: NGuy Streeter <streeter@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During resume, we call hpet_rtc_timer_init after masking an irq bit in
hpet.  This will cause the call to hpet_disable_rtc_channel to be undone
if RTC_AIE is the only bit not masked.

Allowing the cmos interrupt handler to run before resuming caused some
issues where the timer for the alarm was not removed.  This would cause
other, later timers to not be cleared, so utilities such as hwclock
would time out when waiting for the update interrupt.

[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: NDerek Basehore <dbasehore@chromium.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use device_init_wakeup() instead of device_set_wakeup_capable() and move
it before rtc dev registering.  This fixes alarmtimer not registered
when tps6586x rtc is the only wakeup compatible rtc in the system.
Signed-off-by: NDmitry Osipenko <digetx@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

struct memcg_cache_params has a union.  Different parts of this union
are used for root and non-root caches.  A part with destroying work is
used only for non-root caches.

  BUG: unable to handle kernel paging request at 0000000fffffffe0
  IP: kmem_cache_alloc+0x41/0x1f0
  Modules linked in: netlink_diag af_packet_diag udp_diag tcp_diag inet_diag unix_diag ip6table_filter ip6_tables i2c_piix4 virtio_net virtio_balloon microcode i2c_core pcspkr floppy
  CPU: 0 PID: 1929 Comm: lt-vzctl Tainted: G      D      3.10.0-rc1+ #2
  Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
  RIP: kmem_cache_alloc+0x41/0x1f0
  Call Trace:
   getname_flags.part.34+0x30/0x140
   getname+0x38/0x60
   do_sys_open+0xc5/0x1e0
   SyS_open+0x22/0x30
   system_call_fastpath+0x16/0x1b
  Code: f4 53 48 83 ec 18 8b 05 8e 53 b7 00 4c 8b 4d 08 21 f0 a8 10 74 0d 4c 89 4d c0 e8 1b 76 4a 00 4c 8b 4d c0 e9 92 00 00 00 4d 89 f5 <4d> 8b 45 00 65 4c 03 04 25 48 cd 00 00 49 8b 50 08 4d 8b 38 49
  RIP  [<ffffffff8116b641>] kmem_cache_alloc+0x41/0x1f0
Signed-off-by: NAndrey Vagin <avagin@openvz.org>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: NMichal Hocko <mhocko@suse.cz>
Cc: Li Zefan <lizefan@huawei.com>
Cc: <stable@vger.kernel.org>	[3.9.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If an error occurs, for example an EIO in __ocfs2_prepare_orphan_dir,
ocfs2_prep_new_orphaned_file will release the inode_ac, then when the
caller of ocfs2_prep_new_orphaned_file gets a 0 return, it will refer to
a NULL ocfs2_alloc_context struct in the following functions.  A kernel
panic happens.
Signed-off-by: N"Xiaowei.Hu" <xiaowei.hu@oracle.com>
Reviewed-by: Nshencanquan <shencanquan@huawei.com>
Acked-by: NSunil Mushran <sunil.mushran@gmail.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For 'while' looping, need stop when 'nbytes == 0', or will cause issue.
('nbytes' is size_t which is always bigger or equal than zero).

The related warning: (with EXTRA_CFLAGS=-W)

  lib/mpi/mpicoder.c:40:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The dmesg_restrict sysctl currently covers the syslog method for access
dmesg, however /dev/kmsg isn't covered by the same protections.  Most
people haven't noticed because util-linux dmesg(1) defaults to using the
syslog method for access in older versions.  With util-linux dmesg(1)
defaults to reading directly from /dev/kmsg.

To fix /dev/kmsg, let's compare the existing interfaces and what they
allow:

 - /proc/kmsg allows:
  - open (SYSLOG_ACTION_OPEN) if CAP_SYSLOG since it uses a destructive
    single-reader interface (SYSLOG_ACTION_READ).
  - everything, after an open.

 - syslog syscall allows:
  - anything, if CAP_SYSLOG.
  - SYSLOG_ACTION_READ_ALL and SYSLOG_ACTION_SIZE_BUFFER, if
    dmesg_restrict==0.
  - nothing else (EPERM).

The use-cases were:
 - dmesg(1) needs to do non-destructive SYSLOG_ACTION_READ_ALLs.
 - sysklog(1) needs to open /proc/kmsg, drop privs, and still issue the
   destructive SYSLOG_ACTION_READs.

AIUI, dmesg(1) is moving to /dev/kmsg, and systemd-journald doesn't
clear the ring buffer.

Based on the comments in devkmsg_llseek, it sounds like actions besides
reading aren't going to be supported by /dev/kmsg (i.e.
SYSLOG_ACTION_CLEAR), so we have a strict subset of the non-destructive
syslog syscall actions.

To this end, move the check as Josh had done, but also rename the
constants to reflect their new uses (SYSLOG_FROM_CALL becomes
SYSLOG_FROM_READER, and SYSLOG_FROM_FILE becomes SYSLOG_FROM_PROC).
SYSLOG_FROM_READER allows non-destructive actions, and SYSLOG_FROM_PROC
allows destructive actions after a capabilities-constrained
SYSLOG_ACTION_OPEN check.

 - /dev/kmsg allows:
  - open if CAP_SYSLOG or dmesg_restrict==0
  - reading/polling, after open

Addresses https://bugzilla.redhat.com/show_bug.cgi?id=903192

[akpm@linux-foundation.org: use pr_warn_once()]
Signed-off-by: NKees Cook <keescook@chromium.org>
Reported-by: NChristian Kujau <lists@nerdbynature.de>
Tested-by: NJosh Boyer <jwboyer@redhat.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We recently noticed that reboot of a 1024 cpu machine takes approx 16
minutes of just stopping the cpus.  The slowdown was tracked to commit
f96972f2 ("kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()").

The current implementation does all the work of hot removing the cpus
before halting the system.  We are switching to just migrating to the
boot cpu and then continuing with shutdown/reboot.

This also has the effect of not breaking x86's command line parameter
for specifying the reboot cpu.  Note, this code was shamelessly copied
from arch/x86/kernel/reboot.c with bits removed pertaining to the
reboot_cpu command line parameter.
Signed-off-by: NRobin Holt <holt@sgi.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are instances in the kernel where we would like to disable CPU
hotplug (from sysfs) during some important operation.  Today the freezer
code depends on this and the code to do it was kinda tailor-made for
that.

Restructure the code and make it generic enough to be useful for other
usecases too.
Signed-off-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

John W. Linville says:

====================
For now I have dropped the mac80211 tree from this request.
We are developing a little backlog of fixes and I would like to
avoid introducing any more uncertainty to this pull request for the
3.10 stream.  All the other bits are the same as what was in the
2013-06-06 request, including the ath9k fixes intended to address
the problems observed by Linus w/ his Pixel, and a CVE fix for a
potential security issue in the b43 driver.

Regarding the wl12xx bits, Luca says:

"Here are three patches that I'd like to get into 3.10.  Two of them, by
me, are related to the firmware version checks in our driver.  Without
them, the firmwares fail to load.  The other one, by Eliad, fixes a typo
bug in our 5GHz scanning code."

And as for the Bluetooth bits, Gustavo says:

"The following patches are important bug fixes for 3.10, plus the
support for a new device. We do have three fixes from Johan. The first
one is a fix to avoid LE-only devices to rely on the (inexistent)
extended features data. The second patch fixes length checks on
incoming L2CAP signalling PDUs so we can discard PDU whose size
doesn't match the one reported in the header.  The last one fixes
the handling of power on failures, we now report proper errors to
mgmt when hci_dev_open()."

Along with that...

Larry Finger corrects an rtlwifi problem that caused some devices to
refuse to connect to non-WPA2 networks if the device had previously
assocated with a WPA2 network.  He also adds a one-line fix to prevent
false reports from kmemleak.

Mark A. Greer fixes an out of bounds array access in mwifiex.

Felix Fietkau reverts an earlier ath9k initval patch that reduced rx
sensitivity in a number of ath9k devices with no corresponding benefit.

Kees Cook fixes a potential uid-0 to ring-0 escalation in b43
(CVE-2013-2852).

Sujith Manoharan turns-off powersave mode by default for ath9k, and
also defaults ath9k to use the minstrel_ht rate control algorithm.
Both of these are believed to contribute to greater stability/usability
of ath9k in real-world situations.

Yijing Wang fixes an iwlegacy build error for il_pm_ops if CONFIG_PM
is set but CONFIG_PM_SLEEP is not set.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>