Failure of initializing one hctx isn't handled, so this patch
introduces blk_mq_init_hctx() and its pair to handle it explicitly.
Also this patch makes code cleaner.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Some ATA drivers need the dma drain size workaround, and thus need to
call blk_mq_start_request before the S/G mapping.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>

Moved blk_mq_rq_timed_out() definition to the private blk-mq.h header.
Signed-off-by: NJens Axboe <axboe@fb.com>

Commit 8cb34819cdd5d(blk-mq: unshared timeout handler) introduces
blk-mq's own timeout handler, and removes following line:

	blk_queue_rq_timed_out(q, blk_mq_rq_timed_out);

which then causes blk_add_timer() to bypass adding the timer,
since blk-mq no longer has q->rq_timed_out_fn defined.

This patch fixes the problem by bypassing the check for blk-mq,
so that both request deadlines are still set and the rolling
timer updated.
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

It's not uncommon for crash dump kernels to be limited to 128MB or
something low in that area. This is normally not a problem for
devices as we don't use that much memory, but for some shared SCSI
setups with huge queue depths, it can potentially fill most of
memory with tons of request allocations. blk-mq does scale back
when it fails to allocate memory, but it scales back just enough
so that blk-mq succeeds. This could still leave the system with
not enough memory to make any real progress.

Check if we are in a kdump environment and limit the hardware
queues and tag depth.
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch removes two unnecessary blk_clear_rq_complete(),
the REQ_ATOM_COMPLETE flag is cleared inside blk_mq_start_request(),
so:

	- The blk_clear_rq_complete() in blk_flush_restore_request()
	needn't because the request will be freed later, and clearing
	it here may open a small race window with timeout.

	- The blk_clear_rq_complete() in blk_mq_requeue_request() isn't
	necessary too, even though REQ_ATOM_STARTED is cleared in
	__blk_mq_requeue_request(), in theory it still may cause a small
	race window with timeout since the two clear_bit() may be
	reordered.
Signed-off-by: NMing Lei <ming.lei@canoical.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Allow blk-mq to pass an argument to the timeout handler to indicate
if we're timing out a reserved or regular command.  For many drivers
those need to be handled different.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Duplicate the (small) timeout handler in blk-mq so that we can pass
arguments more easily to the driver timeout handler.  This enables
the next patch.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Don't do a kmalloc from timer to handle timeouts, chances are we could be
under heavy load or similar and thus just miss out on the timeouts.
Fortunately it is very easy to just iterate over all in use tags, and doing
this properly actually cleans up the blk_mq_busy_iter API as well, and
prepares us for the next patch by passing a reserved argument to the
iterator.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Now that we've changed the driver API on the submission side use the
opportunity to fix up the name on the completion side to fit into the
general scheme.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

When we call blk_mq_start_request from the core blk-mq code before calling into
->queue_rq there is a racy window where the timeout handler can hit before we've
fully set up the driver specific part of the command.

Move the call to blk_mq_start_request into the driver so the driver can start
the request only once it is fully set up.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Pass an explicit parameter for the last request in a batch to ->queue_rq
instead of using a request flag.  Besides being a cleaner and non-stateful
interface this is also required for the next patch, which fixes the blk-mq
I/O submission code to not start a time too early.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Moving patches from for-linus to 3.18 instead, pull in this changes
that will go to Linus today.

When requests are retried due to hw or sw resource shortages,
we often stop the associated hardware queue. So ensure that we
restart the queues when running the requeue work, otherwise the
queue run will be a no-op.
Signed-off-by: NJens Axboe <axboe@fb.com>

__blk_mq_alloc_rq_maps() can be invoked multiple times, if we scale
back the queue depth if we are low on memory. So don't clear
set->tags when we fail, this is handled directly in
the parent function, blk_mq_alloc_tag_set().
Reported-by: NRobert Elliott  <Elliott@hp.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

We should not insert requests into the flush state machine from
blk_mq_insert_request.  All incoming flush requests come through
blk_{m,s}q_make_request and are handled there, while blk_execute_rq_nowait
should only be called for BLOCK_PC requests.  All other callers
deal with requests that already went through the flush statemchine
and shouldn't be reinserted into it.
Reported-by: NRobert Elliott  <Elliott@hp.com>
Debugged-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch should fix the bug reported in
https://lkml.org/lkml/2014/9/11/249.

We have to initialize at least the atomic_flags and the cmd_flags when
allocating storage for the requests.

Otherwise blk_mq_timeout_check() might dereference uninitialized
pointers when racing with the creation of a request.

Also move the reset of cmd_flags for the initializing code to the point
where a request is freed. So we will never end up with pending flush
request indicators that might trigger dereferences of invalid pointers
in blk_mq_timeout_check().

Cc: stable@vger.kernel.org
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Reported-by: NPaulo De Rezende Pinatti <ppinatti@linux.vnet.ibm.com>
Tested-by: NPaulo De Rezende Pinatti <ppinatti@linux.vnet.ibm.com>
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

When we start the request, we set the deadline and flip the bits
marking the request as started and non-complete. However, it's
important that the deadline store is ordered before flipping the
bits, otherwise we could have a small window where the request is
marked started but with an invalid deadline. This can confuse the
timeout handling.
Suggested-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Pull gfs2 fixes from Steven Whitehouse:
 "Here are a number of small fixes for GFS2.

  There is a fix for FIEMAP on large sparse files, a negative dentry
  hashing fix, a fix for flock, and a bug fix relating to d_splice_alias
  usage.

  There are also (patches 1 and 5) a couple of updates which are less
  critical, but small and low risk"

* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: fix d_splice_alias() misuses
  GFS2: Don't use MAXQUOTAS value
  GFS2: Hash the negative dentry during inode lookup
  GFS2: Request demote when a "try" flock fails
  GFS2: Change maxlen variables to size_t
  GFS2: fs/gfs2/super.c: replace seq_printf by seq_puts

Commit d6bb3e90 ("vfs: simplify and shrink stack frame of
link_path_walk()") introduced build problems with GCC versions older
than 4.6 due to the initialisation of a member of an anonymous union in
struct qstr without enclosing braces.

This hits GCC bug 10676 [1] (which was fixed in GCC 4.6 by [2]), and
causes the following build error:

  fs/namei.c: In function 'link_path_walk':
  fs/namei.c:1778: error: unknown field 'hash_len' specified in initializer

This is worked around by adding explicit braces.

[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
[2] https://gcc.gnu.org/viewcvs/gcc?view=revision&revision=159206

Fixes: d6bb3e90 (vfs: simplify and shrink stack frame of link_path_walk())
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull virtio fixes from Rusty Russell:
 "virtio-rng corner case fixes, with cc:stable.

  Survived a few days in linux-next"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  virtio-rng: skip reading when we start to remove the device
  virtio-rng: fix stuck of hot-unplugging busy device

Pull regmap fix from Mark Brown:
 "Fix registers file in debugfs

  Ensure that the mode reported for the registers file in debugfs is
  accurate by marking it as read only when the define to enable writes
  has not been set.  This is on the edge of being a bug fix but it's
  debugfs and it makes it much easier for users to spot what's going
  wrong when they forget to enable writeability"

* tag 'regmap-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Fix debugfs-file 'registers' mode

Pull input updates from Dmitry Torokhov:
 "A few quirks for i8042/AT keyboards and a small device tree doc fix
  for Atmel Touchscreens"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: atmel_mxt_ts - fix merge in DT documentation
  Input: i8042 - also set the firmware id for MUXed ports
  Input: i8042 - add nomux quirk for Avatar AVIU-145A6
  Input: i8042 - add Fujitsu U574 to no_timeout dmi table
  Input: atkbd - do not try 'deactivate' keyboard on any LG laptops

Cut & paste typo from the line above.
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 9226b5b4 ("vfs: avoid non-forwarding large load after small
store in path lookup") made link_path_walk() always access the
"hash_len" field as a single 64-bit entity, in order to avoid mixed size
accesses to the members.

However, what I didn't notice was that that effectively means that the
whole "struct qstr this" is now basically redundant.  We already
explicitly track the "const char *name", and if we just use "u64
hash_len" instead of "long len", there is nothing else left of the
"struct qstr".

We do end up wanting the "struct qstr" if we have a filesystem with a
"d_hash()" function, but that's a rare case, and we might as well then
just squirrell away the name and hash_len at that point.

End result: fewer live variables in the loop, a smaller stack frame, and
better code generation.  And we don't need to pass in pointers variables
to helper functions any more, because the return value contains all the
relevant information.  So this removes more lines than it adds, and the
source code is clearer too.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull crypto fixes from Herbert Xu:
 "This fixes the newly added drbg generator so that it actually works on
  32-bit machines.  Previously the code was only tested on 64-bit and on
  32-bit it overflowed and simply doesn't work"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: drbg - remove check for uninitialized DRBG handle
  crypto: drbg - backport "fix maximum value checks on 32 bit systems"

Pull vfs fixes from Al Viro:
 "double iput() on failure exit in lustre, racy removal of spliced
  dentries from ->s_anon in __d_materialise_dentry() plus a bunch of
  assorted RCU pathwalk fixes"

The RCU pathwalk fixes end up fixing a couple of cases where we
incorrectly dropped out of RCU walking, due to incorrect initialization
and testing of the sequence locks in some corner cases.  Since dropping
out of RCU walk mode forces the slow locked accesses, those corner cases
slowed down quite dramatically.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  be careful with nd->inode in path_init() and follow_dotdot_rcu()
  don't bugger nd->seq on set_root_rcu() from follow_dotdot_rcu()
  fix bogus read_seqretry() checks introduced in b37199e6
  move the call of __d_drop(anon) into __d_materialise_unique(dentry, anon)
  [fix] lustre: d_make_root() does iput() on dentry allocation failure

The performance regression that Josef Bacik reported in the pathname
lookup (see commit 99d263d4 "vfs: fix bad hashing of dentries") made
me look at performance stability of the dcache code, just to verify that
the problem was actually fixed.  That turned up a few other problems in
this area.

There are a few cases where we exit RCU lookup mode and go to the slow
serializing case when we shouldn't, Al has fixed those and they'll come
in with the next VFS pull.

But my performance verification also shows that link_path_walk() turns
out to have a very unfortunate 32-bit store of the length and hash of
the name we look up, followed by a 64-bit read of the combined hash_len
field.  That screws up the processor store to load forwarding, causing
an unnecessary hickup in this critical routine.

It's caused by the ugly calling convention for the "hash_name()"
function, and easily fixed by just making hash_name() fill in the whole
'struct qstr' rather than passing it a pointer to just the hash value.

With that, the profile for this function looks much smoother.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull parisc updates from Helge Deller:
 "The most important patch is a new Light Weigth Syscall (LWS) for 8,
  16, 32 and 64 bit atomic CAS operations which is required in order to
  be able to implement the atomic gcc builtins on our platform.

  Other than that, we wire up the seccomp, getrandom and memfd_create
  syscalls, fixes a minor off-by-one bug and a wrong printk string"

* 'parisc-3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Implement new LWS CAS supporting 64 bit operations.
  parisc: Wire up seccomp, getrandom and memfd_create syscalls
  parisc: dino: fix %d confusingly prefixed with 0x in format string
  parisc: sys_hpux: NUL terminator is one past the end

in the former we simply check if dentry is still valid after picking
its ->d_inode; in the latter we fetch ->d_inode in the same places
where we fetch dentry and its ->d_seq, under the same checks.

Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

return the value instead, and have path_init() do the assignment.  Broken by
"vfs: Fix absolute RCU path walk failures due to uninitialized seq number",
which was Cc-stable with 2.6.38+ as destination.  This one should go where
it went.

To avoid dummy value returned in case when root is already set (it would do
no harm, actually, since the only caller that doesn't ignore the return value
is guaranteed to have nd->root *not* set, but it's more obvious that way),
lift the check into callers.  And do the same to set_root(), to keep them
in sync.

Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pull ntb driver bugfixes from Jon Mason:
 "NTB driver fixes for queue spread and buffer alignment.  Also, update
  to MAINTAINERS to reflect new e-mail address"

* tag 'ntb-3.17' of git://github.com/jonmason/ntb:
  ntb: Add alignment check to meet hardware requirement
  MAINTAINERS: update NTB info
  NTB: correct the spread of queues over mw's

Pull ARM irq chip fixes from Thomas Gleixner:
 "Another pile of ARM specific irq chip fixlets:

   - off by one bugs in the crossbar driver
   - missing annotations
   - a bunch of "make it compile" updates

  I pulled the lot today from Jason, but it has been in -next for at
  least a week"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: gic-v3: Declare rdist as __percpu pointer to __iomem pointer
  irqchip: gic: Make gic_default_routable_irq_domain_ops static
  irqchip: exynos-combiner: Fix compilation error on ARM64
  irqchip: crossbar: Off by one bugs in init
  irqchip: gic-v3: Tag all low level accessors __maybe_unused
  irqchip: gic-v3: Only define gic_peek_irq() when building SMP

irqchip fixes for v3.17 from Jason Cooper

 - GIC/GICV3: Various fixlets
 - crossbar: Fix off-by-one bug
 - exynos-combiner: Fix arm64 build error

The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Update my contact info to my personal email address and add Dave Jiang.
Signed-off-by: NJon Mason <jon.mason@intel.com>
Signed-off-by: NDave Jiang <dave.jiang@intel.com>

The detection of an uneven number of queues on the given memory windows
was not correct.  The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Signed-off-by: NJon Mason <jon.mason@intel.com>

read_seqretry() returns true on mismatch, not on match...

Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

and lock the right list there

Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>