In x2apic mode, we need to set the upper address register of the fault
handling interrupt register of the vt-d hardware. Without this
irq migration of the vt-d fault handling interrupt is broken.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <1291225233.2648.39.camel@sbsiddha-MOBL3>
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: NChris Wright <chrisw@sous-sol.org>
Tested-by: NTakao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.

During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).

Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the  system to hang.

Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: stable@kernel.org	[v2.6.32+]
Reported-by: NMax Asbock <masbock@linux.vnet.ibm.com>
Reported-and-tested-by: NTakao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Alignment of alloc_bootmem() depends on the value of
L1_CACHE_SHIFT. What we need here, however, is 64 byte alignment.  Use
alloc_bootmem_align() and explicitly specify the alignment instead.

This fixes a kernel boot crash reported by Jody when the cpu in .config
is set to MPENTIUMII but the kernel is booted on a xsave-capable CPU.
Reported-by: NJody Bruchon <jody@nctritech.com>
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101116212442.059967454@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>

Add an alloc_bootmem_align() interface to allocate bootmem with
specified alignment.  This is necessary to be able to allocate the
xsave area in a subsequent patch.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101116212441.977574826@sbsiddha-MOBL3.sc.intel.com>
Acked-by: NH. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>

The vdso Makefile passes linker-style -m options not to the linker but
to gcc.  This happens to work with earlier gcc, but fails with gcc
4.6.  Pass gcc-style -m options, instead.

Note: all currently supported versions of gcc supports -m32, so there
is no reason to conditionalize it any more.
Reported-by: NH. J. Lu <hjl.tools@gmail.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <tip-*@git.kernel.org>
Cc: <stable@kernel.org>

commit 995bd3bb (x86: Hpet: Avoid the comparator readback penalty)
chose 8 HPET cycles as a safe value for the ETIME check, as we had the
confirmation that the posted write to the comparator register is
delayed by two HPET clock cycles on Intel chipsets which showed
readback problems.

After that patch hit mainline we got reports from machines with newer
AMD chipsets which seem to have an even longer delay. See
http://thread.gmane.org/gmane.linux.kernel/1054283 and
http://thread.gmane.org/gmane.linux.kernel/1069458 for further
information.

Boris tried to come up with an ACPI based selection of the minimum
HPET cycles, but this failed on a couple of test machines. And of
course we did not get any useful information from the hardware folks.

For now our only option is to chose a paranoid high and safe value for
the minimum HPET cycles used by the ETIME check. Adjust the minimum ns
value for the HPET clockevent accordingly.
Reported-Bistected-and-Tested-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1012131222420.2653@localhost6.localdomain6>
Cc: Simon Kirby <sim@hostway.ca>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andreas Herrmann <Andreas.Herrmann3@amd.com>
Cc: John Stultz <johnstul@us.ibm.com>

arch/x86/kernel/apic/io_apic.c: In function 'ack_apic_level':
arch/x86/kernel/apic/io_apic.c:2433: warning: unused variable 'desc'
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
LKML-Reference: <201010272107.o9RL7rse018212@imap1.linux-foundation.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Merge branches 'x86-fixes-for-linus', 'perf-fixes-for-linus' and 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86/pvclock: Zero last_value on resume

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf record: Fix eternal wait for stillborn child
  perf header: Don't assume there's no attr info if no sample ids is provided
  perf symbols: Figure out start address of kernel map from kallsyms
  perf symbols: Fix kallsyms kernel/module map splitting

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  nohz: Fix printk_needs_cpu() return value on offline cpus
  printk: Fix wake_up_klogd() vs cpu hotplug

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: i915 cannot provide switcher services.
  drm/radeon/kms: fix vram base calculation on rs780/rs880
  drm/radeon/kms: fix formatting of vram and gtt info
  drm/radeon/kms: forbid big bo allocation (fdo 31708) v3
  drm: Don't try and disable an encoder that was never enabled
  drm: Add missing drm_vblank_put() along queue vblank error path
  drm/i915/dp: Only apply the workaround if the select is still active
  drm/i915: Emit a request to clear a flushed and idle ring for unbusy bo
  drm/i915/lvds: Always restore panel-fitter when enabling the LVDS
  drm/i915/ringbuffer: Only print an error on the second attempt to reset head
  drm/i915: announce to userspace that the bsd ring is coherent
  agp/intel: Fix wrong kunmap in i830_cleanup()
  drm/i915: Factor in pixel-repeat in FDI M/N calculation
  drm/i915: Death to the unnecessary 64bit divide
  drm/i915: Clean conflicting modesetting registers upon init
  drm/i915: Apply a workaround for transitioning from DP on pipe B to HDMI.
  drm/i915: Always set the DP transcoder config to 8BPC.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wacom - add new Bamboo PT (0xdb)
  Input: add input driver for polled GPIO buttons
  Input: turbografx - fix reference counting
  Input: synaptics - fix handling of 2-button ClickPads
  Input: wacom - add IDs for two new Bamboo PTs
  Input: document struct input_absinfo
  Input: add keycodes for touchpad on/off keys
  Input: usbtouchscreen - add support for LG Flatron T1710B

it has a DSM but the switcher is done via WMI.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Adds new Bamboo Pen & Touch model - Bamboo P & T Special Edition
Medium (CTH661/L; Product ID = 0xdb).
Tested-by: NTobias Verbeke <tobias.verbeke@gmail.com>
Signed-off-by: NDavid Foley <favux.is@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

* 'fixes/2637-rc5/s3c24xx' of git://git.fluff.org/bjdooks/linux:
  ARM: S3C24XX: Fix mess with gpio {set,get}_pull callbacks
  ARM: mini2440: Fix Kconfig to allow kernel to build
  ARM: S3C2412: Fix typo in CONFIG_CPU_S3C2412_ONLY definition
  ARM: S3C2443: Select properly ARM core type
  ARM: SMDK2416: Select MACH_SMDK, S3C_DEV_NAND, S3C_DEV_USB_HOST

Currently the {set,get}_pull callbacks of the s3c24xx_gpiocfg_default structure
are initalized via s3c_gpio_{get,set}pull_1up. This results in a linker
error when only CONFIG_CPU_S3C2442 is selected:

arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f4): undefined reference to
`s3c_gpio_getpull_1up'
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f8): undefined reference to
`s3c_gpio_setpull_1up'

The s3c2442 has pulldowns instead of pullups compared to the s3c2440.
The method of controlling them is the same though.
So this patch modifies the existing s3c_gpio_{get,set}pull_1up helper functions
to take an additional parameter deciding whether the pin has a pullup or pulldown.
The s3c_gpio_{get,set}pull_1{down,up} functions then wrap that functions passing
either S3C_GPIO_PULL_UP or S3C_GPIO_PULL_DOWN.

Furthermore this patch sets up the s3c24xx_gpiocfg_default.{get,set}_pull fields
in the s3c244{0,2}_map_io function to the new pulldown helper functions.

Based on patch from "Lars-Peter Clausen" <lars@metafoo.de>
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Avoid overflowing a 32 bit value.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

print the full 64 bit values.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Forbid allocating buffer bigger than visible VRAM or GTT, also
properly set lpfn field.

v2 - use max macro
   - silence warning
v3 - don't explicitly set range limit
   - use min macro

Cc: stable <stable@kernel.org>
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prevents code that assumes that the encoder is active when asked to be
disabled from dying a horrible death.
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel into drm-fixes

As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.

Fixes regression in 5bddd17f.
Reported-and-tested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17f]

Fix the name of interrupt mask alteration function (ie the
local_change_intr_mask_level() fn) called in gdbstub to have an arch_
prefix to match the definition in asm/irqflags.h.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix incorrect proc spurious output

Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
  wmi: use memcmp instead of strncmp to compare GUIDs
  ACPI, hp-wmi: Fix memory leak in acpi query
  msi-wmi: fix semantically incorrect use of keycode instead of scancode
  msi-wmi: Add mute key support
  asus-laptop: add wimax and wwan support
  eeepc-wmi: fix compiler warning
  ibm_rtl: _RTL_ is not available in UEFI mode
  ibm_rtl: Loosen the DMI criteria to all IBM machines
  drivers/platform/x86/thinkpad_acpi.c: delete double assignment
  eeepc-wmi: add cpufv sysfs documentation
  toshiba_acpi.c: Add key_entry for a lone FN keypress
  ibm_rtl: fix printk format warning

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] css: fix rsid evaluation for 2nd crw
  [S390] nohz/s390: fix arch_needs_cpu() return value on offline cpus

With the recent changes to remove the BKL a mutex was added to the
ioctl entry point for calls to the old ioctl interface. This mutex
needs to be removed because of the need for the expire ioctl to call
back to the daemon to perform a umount and receive a completion
status (via another ioctl).

This should be fine as the new ioctl interface uses much of the same
code and it has been used without a mutex for around a year without
issue, as was the original intention.

Ref: Bugzilla bug 23142
Signed-off-by: NIan Kent <raven@themaw.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order for bos to retire eventually, a request must be sent down the
ring. This is expected, for example, by occlusion queries for which mesa
will wait upon (whilst running glean) before issuing more batches and so
the normal activity upon the ring is suspended and we need to emit a
request to clear the idle ring.
Reported-by: NJinjin, Wang <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2_connection_find() returns pointer to bad structure
  ocfs2: char is not always signed
  Ocfs2: Stop tracking a negative dentry after dentry_iput().
  ocfs2: fix memory leak
  fs/ocfs2/dlm: Use GFP_ATOMIC under spin_lock

Commit 0ea12930 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.

Fix that.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The existing gpio-keys driver can be usable only for GPIO lines with
interrupt support. Several devices have buttons connected to a GPIO
line which is not capable to generate interrupts. This patch adds a
new input driver using the generic GPIO layer and the input-polldev
to support such buttons.

[Ben Gardiner <bengardiner@nanometrics.ca: fold code to use more
 of the original gpio_keys infrastructure; cleanups and other
 improvements.]
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NBen Gardiner <bengardiner@nanometrics.ca>
Tested-by: NBen Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Hibernate: Fix memory corruption related to swap
  PM / Hibernate: Use async I/O when reading compressed hibernation image

There is a problem that swap pages allocated before the creation of
a hibernation image can be released and used for storing the contents
of different memory pages while the image is being saved.  Since the
kernel stored in the image doesn't know of that, it causes memory
corruption to occur after resume from hibernation, especially on
systems with relatively small RAM that need to swap often.

This issue can be addressed by keeping the GFP_IOFS bits clear
in gfp_allowed_mask during the entire hibernation, including the
saving of the image, until the system is finally turned off or
the hibernation is aborted.  Unfortunately, for this purpose
it's necessary to rework the way in which the hibernate and
suspend code manipulates gfp_allowed_mask.

This change is based on an earlier patch from Hugh Dickins.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHugh Dickins <hughd@google.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: stable@kernel.org

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6524/1: GIC irq desciptor bug fix
  ARM: 6523/1: iop: ensure sched_clock() is notrace
  ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
  ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
  ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
  ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
  ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
  ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
  ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
  ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
  ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
  ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
  ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
  ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
  ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
  ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
  ARM: cns3xxx: Fix build with CONFIG_PCI=y

This is a fix for reading LZO compressed image using async I/O.
Essentially, instead of having just one page into which we keep
reading blocks from swap, we allocate enough of them to cover the
largest compressed size and then let block I/O pick them all up. Once
we have them all (and here we wait), we decompress them, as usual.
Obviously, the very first block we still pick up synchronously,
because we need to know the size of the lot before we pick up the
rest.

Also fixed the copyright line, which I've forgotten before.
Signed-off-by: NBojan Smojver <bojan@rexursive.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

While looking for the duplicates in /sys/class/wmi/, I couldn't find
them. The code that looks for duplicates uses strncmp in a binary GUID,
which may contain zero bytes. The right function is memcmp, which is
also used in another section of wmi code.

It was finding 49142400-C6A3-40FA-BADB-8A2652834100 as a duplicate of
39142400-C6A3-40FA-BADB-8A2652834100. Since the first byte is the fourth
printed, they were found as equal by strncmp.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org

When execvp fails to find the specified command on the path we won't get
SIGCHLD, so send a SIGUSR1 and exit right away.

Current situation would require a SIGINT performed by the user and would
produce meaningless summary.

Now:

[acme@emilia linux]$ ./foo
-bash: ./foo: No such file or directory
[acme@emilia linux]$ perf record ./foo
./foo: No such file or directory
[acme@emilia linux]$
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: Fix a crash during slabinfo -v