Two type of NVM available for devices 1000, 6000 and after, adding
support to read OTP lower blocks if OTP is used instead of EEPROM.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The USB ID with unknown manufacturer is apparently sweex,
copy it to the correct location of the list and add 2
additional USB ID's also belonging to Sweex.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

set_infra_mode() tried to restore wpa keys using add_wep_key(). This never
worked so prevent driver from trying.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split add_wpa_key() from rndis_iw_set_encode_ext so that conversion to cfg80211
would be easier later on.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver uses some unnamed bits to control encryption setup. Move these to
enumerations with proper names explaining their meaning.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BCM4320 doesn't support OID_802_11_TX_POWER_LEVEL (chip implements
the command but setting value has no effect and getting txpower value
always returns 0xff, full power). So remove the code for cleanup.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Old variant of bcm4320 doesn't handle setting configuration parameters
correctly. One symptom is that MAC gets partially overwritten when any
config parameters are set. This patch disables config-params for bcm4320a
(and generic rndis-wlan).
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The temperature measurement by uCode for 5150 and 5000 are different
        CSR_HW_REV_TYPE_5150: temperature sensor output voltage
        CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.

To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add "Greenfield" support for all devices except 4965 and
3945. "Greenfield" is part of 11n features to improve HT performance.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'tpt' is a delta throughput (number of packets) and is corelated
to brightness of the LED. We already maintain a delta of packets in
rxtxpackets. There is no need to calculate this delta again which
was affecting the behaviour of LEDS.

Also add two new callback functions for ASSOCIATED/DISASSOCIATED states
where LED's will be *on* for associated state and *off* for disassociated state.

This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1771.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.

SD8688 firmware introduces a new register for firmware status
which will never be overwritten.

Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver supports Intel's full MAC wireless multicomm 802.11 hardware.
Although the hardware is a 802.11agn device, we currently only support
802.11ag, in managed and ad-hoc mode (no AP mode for now).
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some APs seem to drift away from the expected TBTT (timestamp %
beacon_int_in_usec differs quite a bit from zero) which can result in
us waking up way too early to receive a Beacon frame. In order to work
around this, re-configure the Beacon timers after having received a
Beacon frame from the AP (i.e., when we know the offset between the
expected TBTT and the actual time the AP is sending out the Beacon
frame).
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The previous version used a simple loop to go through all Beacon
frames when determining the next TBTT and DTIM count. This is not too
bad for the case where the setup happens before timesync (i.e., very
small TSF), but this can become very heavy operation if a short Beacon
interval is used and the current TSF is large.

In preparation for a patch to update timer setup based on Beacon
timestamp, optimize this routine to take fixed time regardless of the
actual TSF value.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.

When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).

This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: 	IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688:	IF_SDIO_SCRATCH     (0x34/0x35)

Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN  0x42 is read every time when rx interrupt is received.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in.  This
can lead, for example, to the card failing to re-associate.  This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is always discarded anyway but lets just set this to our
safest lowest.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath_regd_init() needs to be called with the wiphy already
properly set with the bands. Without this the custom regulatory
settings were not taking effect, and the device would get
the default channel settings from ath9k_[25]ghz_chantable.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report status unknown as if there were successfully transmitted.
This will avoid hostapd to disassociate because it doesn't understand what a status unknown is.
Signed-off-by: NAlexandre Becholey <alexandre.becholey@epfl.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 does not set PM field for normal data frames, so we need to
update that based on the current PS mode when using PS-Poll
(timeout=0) power save mode.

This allows the AP to remain in sync with our PS state. However, there
is still a potential race condition between PS state changes when
multiple TX queues are used and nullfunc and PS-Poll frames use
different queue. That corner case may need to be handled separately by
changing which queue is used either in ath9k or mac80211.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We must make sure the chip is awake when changing the RX filter
parameters. This could have caused problems, e.g., when changing the
interface to promiscuous mode while in sleep mode.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the chip complains about TSF sync, make sure we remain awake to
sync with the next Beacon frame. In theory, this should not be needed
since we are currently trying to receive all Beacon frames, anyway,
better have this code ready should we ever change that.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the chip is in sleep mode, there is no point trying to calibrate
the radio since it will just results in incorrect values being read
from registers and other potential issues. In addition, if we actually
start processing calibrate, do not allow the chip to be put into sleep
until we have completed the calibration step.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using timeout=0 (PS-Poll) with mac80211, the driver will need to
wake up for TX requests and remain awake until the TX has been
completed (ACK received or timeout) or until the buffer frame(s) have
been received (in case the TX is for a PS-Poll frame).
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we are trying to interpolate a curve with slope == 0, the return
value will always be the y-coordinate.  In this code we are looping
until we reach a minimum y-coordinate on a line, which in the 0-slope
case can never happen, thus the loop never terminates.

The PCDAC steps come from the EEPROM and should never be equal, but
we should gracefully handle that case, so warn and bail out.
Reported-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fix to set dev->broadcast correctly, since
dev->broadcast is defined as:
  unsigned char broadcast[MAX_ADDR_LEN];
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix this build error:
drivers/staging/agnx/pci.c: In function 'agnx_config_interface':
drivers/staging/agnx/pci.c:315: error: dereferencing pointer to incomplete type
..
drivers/staging/agnx/pci.c:424: error: unknown field 'config_interface' specified in initializer

config_interface was removed in 2d0ddec5
("mac80211: unify config_interface and bss_info_changed")
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do not need to do this in ath_isr() and it looks like the modified
version ends up being more stable as far as being able receive beacon
frames is concerned. Furthermore, this reduces need to move between
AWAKE and NETWORK SLEEP states when processing some unrelated
interrupts.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently all radios receive all traffic on the simulated air
if they are tuned to the same channel. This patch introduces
the concept of grouping, which allows to assign a radio to
certain group. Only radios in the same group can 'see' each other.

Each bit in /debug/ieee80211/phy*/hwsim/group
represents one group. By default all radios belong to the same group "1",
e.g. bit 1 is set. Additionally a radio can belong to several groups.
Signed-off-by: NDaniel Wagner <wagi@monom.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k only generated the beacon when bss_info_changed() was called,
but for AP mode this is not enough, because the TIM IE would never
get updated and consequently PS mode clients wouldn't know about
buffered frames.  Instead, get a new beacon on every SWBA interrupt.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drop test for FW_STATE_RESET in p54spi_work as fw_state
is never assigned this value.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Process beacon change even if the BSSID doesn't
change at the same time. Also fix what I think
is a small locking error in b43legacy, there's
a spin_unlock_irqrestore that looks out of place.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under high load first data word, read after available data size
is sometimes lost in p54spi_rx. It seems to depend on frequency
of interrupts and latency of data read request relatively to
'data available' interrupt. The worst consequence of this bug
is loss of packet transmission acknowledgement, which in turn
causes overflow of tx queues and permanent link loss.

Read data size and first data word in one SPI transaction.
No packets from LMAC should have length less than 1 word,
so this shouldn't interfere with the next read transaction.

Also call p54spi_sleep if p54spi_wake succeeded.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Put chip into sleep state, once it's been awaken.
Also, propagate error code to the caller.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Return whether wakeup operation succeeded.
Make use of this return value.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>