It's annoying to constantly see the same "Not yet implemented" message
over and over with nothing able to be done about it, so rate limit it
for now to keep user's logs "clean".
Reported-by: NLars Täuber <lars.taeuber@web.de>
Tested-by: NLars Täuber <lars.taeuber@web.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.

Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'phy-for-4.7-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus

Kishon writes:

phy: for 4.7-rc

*) Fix compiler warning in exynos-mipi-video
*) Fix in ti-pipe3 PHY to program the DPLL
   even if it was already locked
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

This patch protects system from crashing at shutdown in
cases where usb host is not added yet from OTG controller driver.
As ehci_setup() not done yet, so stop accessing registers or
variables initialized as part of ehci_setup().

The use case is simple, for boards like DB410c where the usb host
or device functionality is decided based on the micro-usb cable
presence. If the board boots up with micro-usb connected, the
OTG driver like echi-msm would not add the usb host by default.
However a system shutdown would go and access registers and
uninitialized variables, resulting in below crash.

Unable to handle kernel NULL pointer dereference at virtual address
 00000008
pgd = ffffffc034581000
[00000008] *pgd=0000000000000000, *pud=0000000000000000
CPU: 2 PID: 1957 Comm: reboot Not tainted 4.6.0+ #99
task: ffffffc034bc0000 ti: ffffffc0345cc000 task.ti: ffffffc0345cc000
PC is at ehci_halt+0x54/0x108
LR is at ehci_halt+0x38/0x108
pc : [<ffffff800869837c>] lr : [<ffffff8008698360>] pstate: a00001c5
sp : ffffffc0345cfc60
x29: ffffffc0345cfc60 x28: ffffffc0345cc000
x27: ffffff8008a4d000 x26: 000000000000008e
x25: ffffff8008d86cb0 x24: ffffff800908b040
x23: ffffffc036068870 x22: ffffff8009d0a000
x21: ffffffc03512a410 x20: ffffffc03512a410
x19: ffffffc03512a338 x18: 00000000000065ba
x17: ffffff8009b16b80 x16: 0000000000000003
x15: 00000000000065b9 x14: 00000000000065b6
x13: 0000000000000000 x12: 0000000000000000
x11: 000000000000003d x10: ffffffc0345cf9e0
x9 : 0000000000000001 x8 : ffffffc0345cc000
x7 : ffffff8008698360 x6 : 0000000000000000
x5 : 0000000000000080 x4 : 0000000000000001
x3 : 0000000000000000 x2 : 0000000000000000
x1 : 0000000000000008 x0 : ffffffc034bc0000

Process reboot (pid: 1957, stack limit = 0xffffffc0345cc020)
Stack: (0xffffffc0345cfc60 to 0xffffffc0345d0000)
fc60: ffffffc0345cfc90 ffffff8008698448 ffffffc03512a338 ffffffc03512a338
fc80: ffffffc03512a410 ffffff8008a3bbfc ffffffc0345cfcc0 ffffff8008698548
fca0: ffffffc03512a338 ffffffc03512a000 ffffffc03512a410 ffffff8009d0a000
fcc0: ffffffc0345cfcf0 ffffff800865d2bc ffffffc036068828 ffffffc036068810
fce0: ffffffc036003810 ffffff800853f43c ffffffc0345cfd00 ffffff800854338c
fd00: ffffffc0345cfd10 ffffff800853f45c ffffffc0345cfd60 ffffff80080e0f48
fd20: 0000000000000000 0000000001234567 ffffff8008f8c000 ffffff8008f8c060
fd40: 0000000000000000 0000000000000015 0000000000000120 ffffff80080e0f30
fd60: ffffffc0345cfd70 ffffff80080e1020 ffffffc0345cfd90 ffffff80080e12fc
fd80: 0000000000000000 0000000001234567 0000000000000000 ffffff8008085e70
fda0: 0000000000000000 0000005592905000 ffffffffffffffff 0000007f79daf1cc
fdc0: 0000000000000000 0000000000000000 0000007ffcbb1198 000000000000000a
fde0: 00000055928d3f58 0000000000000001 ffffffc034900000 00000000fffffffe
fe00: ffffffc034900000 0000007f79da902c ffffffc0345cfe40 ffffff800820af38
fe20: 0000000000000000 0000007ffcbb1078 ffffffffffffffff ffffff80081e9b38
fe40: ffffffc0345cfe60 ffffff80081eb410 ffffffc0345cfe60 ffffff80081eb444
fe60: ffffffc0345cfec0 ffffff80081ec4f4 0000000000000000 0000007ffcbb1078
fe80: ffffffffffffffff 0000000000000015 ffffffc0345cfec0 0000007ffcbb1078
fea0: 0000000000000002 000000000000000a ffffffffffffffff 0000000000000000
fec0: 0000000000000000 ffffff8008085e70 fffffffffee1dead 0000000028121969
fee0: 0000000001234567 0000000000000000 ffffffffffffffff 8080800000800000
ff00: 0000800000808080 0000007ffcbb10f0 000000000000008e fefeff54918cb8c7
ff20: 7f7f7f7fffffffff 0101010101010101 0000000000000010 0000000000000000
ff40: 0000000000000000 0000007f79e33588 0000005592905eb8 0000007f79daf1b0
ff60: 0000007ffcbb1340 0000005592906000 0000005592905000 0000005592906000
ff80: 0000005592907000 0000000000000002 0000007ffcbb1d98 0000005592906000
ffa0: 00000055928d2000 0000000000000000 0000000000000000 0000007ffcbb1aa0
ffc0: 00000055928b819c 0000007ffcbb1aa0 0000007f79daf1cc 0000000000000000
ffe0: fffffffffee1dead 000000000000008e 05ef555057155555 d555544d55d775d3
Call trace:
Exception stack(0xffffffc0345cfaa0 to 0xffffffc0345cfbc0)
Set corner to 6
faa0: ffffffc03512a338 ffffffc03512a410 ffffffc0345cfc60 ffffff800869837c
fac0: ffffff8008114210 0000000100000001 ffffff8009ce1b20 ffffff8009ce5f20
fae0: ffffffc0345cfb80 ffffff80081145a8 ffffffc0345cfc10 ffffff800810b924
fb00: ffffffc0345cc000 00000000000001c0 ffffffc03512a410 ffffff8009d0a000
fb20: ffffffc036068870 ffffff800908b040 ffffff8008d86cb0 000000000000008e
fb40: ffffffc034bc0000 0000000000000008 0000000000000000 0000000000000000
fb60: 0000000000000001 0000000000000080 0000000000000000 ffffff8008698360
fb80: ffffffc0345cc000 0000000000000001 ffffffc0345cf9e0 000000000000003d
fba0: 0000000000000000 0000000000000000 00000000000065b6 00000000000065b9
[<ffffff800869837c>] ehci_halt+0x54/0x108
[<ffffff8008698448>] ehci_silence_controller+0x18/0xcc
[<ffffff8008698548>] ehci_shutdown+0x4c/0x64
[<ffffff800865d2bc>] usb_hcd_platform_shutdown+0x1c/0x24
[<ffffff800854338c>] platform_drv_shutdown+0x20/0x28
[<ffffff800853f45c>] device_shutdown+0xf4/0x1b0
[<ffffff80080e0f48>] kernel_restart_prepare+0x34/0x3c
[<ffffff80080e1020>] kernel_restart+0x14/0x74
[<ffffff80080e12fc>] SyS_reboot+0x110/0x21c
[<ffffff8008085e70>] el0_svc_naked+0x24/0x28
Code: 53001c42 350000a2 d5033e9f 91002021 (b9000022)

Fixes 4bb3cad7 ("usb: host: ehci-msm: Register usb shutdown function")
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: NPramod Gurav <pramod.gurav@linaro.org>
Tested-by: NAndy Gross <andy.gross@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a suspend/resume issue where the driver is blindly
calling ehci_suspend/resume functions when the ehci hasn't been setup.
This results in a crash during suspend/resume operations.
Signed-off-by: NAndy Gross <andy.gross@linaro.org>
Tested-by: NPramod Gurav <pramod.gurav@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Starting with commit 0b52297f ("reset: Add support for shared reset
controls") there is a reference count for reset control assertions. The
goal is to allow resets to be shared by multiple devices and an assert
will take effect only when all instances have asserted the reset.

In order to preserve backwards-compatibility, all reset controls become
exclusive by default. This is to ensure that reset_control_assert() can
immediately assert in hardware.

However, this new behaviour triggers the following warning in the EHCI
driver for Tegra:

[    3.365019] ------------[ cut here ]------------
[    3.369639] WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x16c/0x23c
[    3.382151] Modules linked in:
[    3.385214] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc6-next-20160503 #140
[    3.392769] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[    3.399046] [<c010fa50>] (unwind_backtrace) from [<c010b120>] (show_stack+0x10/0x14)
[    3.406787] [<c010b120>] (show_stack) from [<c0347dcc>] (dump_stack+0x90/0xa4)
[    3.414007] [<c0347dcc>] (dump_stack) from [<c011f4fc>] (__warn+0xe8/0x100)
[    3.420964] [<c011f4fc>] (__warn) from [<c011f5c4>] (warn_slowpath_null+0x20/0x28)
[    3.428525] [<c011f5c4>] (warn_slowpath_null) from [<c03cc8cc>] (__of_reset_control_get+0x16c/0x23c)
[    3.437648] [<c03cc8cc>] (__of_reset_control_get) from [<c0526858>] (tegra_ehci_probe+0x394/0x518)
[    3.446600] [<c0526858>] (tegra_ehci_probe) from [<c04516d8>] (platform_drv_probe+0x4c/0xb0)
[    3.455029] [<c04516d8>] (platform_drv_probe) from [<c044fe78>] (driver_probe_device+0x1ec/0x330)
[    3.463892] [<c044fe78>] (driver_probe_device) from [<c0450074>] (__driver_attach+0xb8/0xbc)
[    3.472320] [<c0450074>] (__driver_attach) from [<c044e1ec>] (bus_for_each_dev+0x68/0x9c)
[    3.480489] [<c044e1ec>] (bus_for_each_dev) from [<c044f338>] (bus_add_driver+0x1a0/0x218)
[    3.488743] [<c044f338>] (bus_add_driver) from [<c0450768>] (driver_register+0x78/0xf8)
[    3.496738] [<c0450768>] (driver_register) from [<c010178c>] (do_one_initcall+0x40/0x170)
[    3.504909] [<c010178c>] (do_one_initcall) from [<c0c00ddc>] (kernel_init_freeable+0x158/0x1f8)
[    3.513600] [<c0c00ddc>] (kernel_init_freeable) from [<c0810784>] (kernel_init+0x8/0x114)
[    3.521770] [<c0810784>] (kernel_init) from [<c0107778>] (ret_from_fork+0x14/0x3c)
[    3.529361] ---[ end trace 4bda87dbe4ecef8a ]---

The reason is that Tegra SoCs have three EHCI controllers, each with a
separate reset line. However the first controller contains UTMI pads
configuration registers that are shared with its siblings and that are
reset as part of the first controller's reset. There is special code in
the driver to assert and deassert this shared reset at probe time, and
it does so irrespective of which controller is probed first to ensure
that these shared registers are reset before any of the controllers are
initialized. Unfortunately this means that if the first controller gets
probed first, it will request its own reset line and will subsequently
request the same reset line again (temporarily) to perform the reset.
This used to work fine before the above-mentioned commit, but now
triggers the new WARN.

Work around this by making sure we reuse the controller's reset if the
controller happens to be the first controller.

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.

Commit a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.

This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.

Fixes: a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

parport subsystem has introduced parport_del_port() to delete a port
when it is going away. Without parport_del_port() the registered port
will not be unregistered.
To reproduce and verify the error:
Command to be used is : ls /sys/bus/parport/devices
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and the command still shows "parport0".
4) Attach the device again and we get "parport1".

With the patch applied:
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and there is no output as "parport0" is now
removed.
4) Attach device again to get "parport0" again.

Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: NSudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.

This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.

The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.

Fix ed_schedule to update ED state only on successful return.
Signed-off-by: NMichal Pecio <michal.pecio@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If bootloader has set a wrong DPLL then we must trash those values
and re-program it anyways. This fixes USB3 devices not being enumerated
on beagle-x15 if usb was started in u-boot.

We don't re-program SATA DPLL if it is locked as it was causing
SATA failures if device was hotpluged after boot.
Reported-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().

Fixes: 069a3fd1 (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)

Cc: <stable@vger.kernel.org> # v4.2+
Reported-by: NMatwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.

This solves the device enumeration failure in otg mode exposed by commit
56f487c7 (PM / Runtime: Update last_busy in rpm_resume).

Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We need to check the state for the PHY with delayed_work
as otherwise MUSB will get confused and idles immediately.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There's no longer any need for custom initcall level for
musb.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With the pull up being handled with delayed work, we can
now finally remove pm_runtime_set_irq_safe that blocks the
MUSB glue from idling.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With PM runtime behaving, these are all now unnecessary.
Doing pm_runtime_get(musb->controller) will keep the parent
glue layer also active.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

At least on n900 we have phy-twl4030-usb only generating cable
interrupts, and then have a separate USB PHY.

In order for musb to know the real cable status, we need to
clear any cached state until musb is ready. Otherwise the cable
status interrupts will get just ignored if the status does
not change from the initial state.

To do this, let's add a return value to musb_mailbox(), and
reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause
a bit of churn here, I should have added that already last time
patching musb_mailbox().
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

At least 2430 glue layer pulls d+ high on start up even if there are
no gadgets configured. This is bad at least for anything using a separate
battery charger chip as it can confuse the charger detection.

Let's fix the issue by removing the bogus glue layer code tinkering
with the SESSION bit. As pointed out Bin Liu <b-liu@ti.com> and
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>, the SESSION
bit just starts host mode if ID pin is grounded, and starts the
srp is ID pin is floating. So without the ID pin changing, it's
unable to force musb mode to anything. And just for starting a
host mode, things work fine without this code.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is no longer needed with PM runtime at least for 2430 glue.
We can now rely only on PM runtime and cable detection.

The other glue layers can probably remove try_idle too, but that
needs to be tested for each platform before doing it.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This simplifies things and allows idling both MUSB and PHY
when nothing is configured. Let's just return early from PM
runtime if musb is not yet initialized.

Let's also warn if PHY is not configured.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We may have drivers loaded but no configured gadgets and MUSB may be in
host mode. If gadgets are configured during host mode, PM runtime will
get confused.

Disable PM runtime from gadget state, and do it based on the cable
and last state.

Note that we may get multiple cable events, so we need to keep track
of the power state.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We have MUSB setting pm_runtime_irq_safe with the following
commits:

30a70b02 ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
3e43a072 ("usb: musb: core: add pm_runtime_irq_safe()")

Let's fix things to use delayed work so we can remove the
pm_runtime_irq_safe.

Note that we may want to set this up in a generic way in the
gadget framework eventually.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The conditional use of PM runtime does not work properly
for musb gadget. On cable disconnect we may not get any
USB_EVENT_NONE leaving the PM runtime call unpaired.

Let's fix the issue by making sure the PM runtime calls are
paired within the functions. The glue layer will take care
of the rest.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Let's not tinker with the PM runtime of musb core from the omap2430
wrapper. This allows us to initialize PM runtime for musb core later
on instead of doing it in stages. And omap2430 wrapper has no need
to for accessing musb core at this point.

Note that this does not remove all the PM runtime calls from the
glue layer, those will get removed in a later patch.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Let's make the PM runtime use the standard autosuspend calls.
Commit 5de85b9d ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") means we must pair use_autosuspend with
dont_use_autosuspend and then use put_sync to properly idle the
device.

Note that we'll be removing the PM runtime calls from the glue
layer to the MUSB core in the next patch. And we can also remove
the pointless FIXME comment now.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We have remove() already calling shutdown(), so let's drop it
and move the code to remove(). No code changes, we'll drop the
the FIXME in the following patch with more clean-up.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Looks like at least 2430 glue won't idle reliably with the 200 ms
autosuspend delay. This causes deeper idle states being blocked for
the whole SoC when disconnecting OTG A cable.

Increasing the delay to 500 ms seems to idle both MUSB and the PHY
reliably. This is probably because of time needed by the hardware
based negotiation between MUSB and the PHY.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.

This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the mode handling to the platform_set_mode callback.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that the DMA engine check was moved to musb_tx_dma_porgram(), both
musb_tx_dma_set_mode_cppi_tusb() and musb_tx_dma_set_mode_mentor() always
return 0, so we can  make both these functions *void*.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 754fe4a9 ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
looks incomplete: the DMA engine checks are  done outside the Mentor/UX500
handler  but inside the CPPI/TUSB handler. Move the checks out of the CPPI/
TUSB handler into its caller, musb_tx_dma_program().
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

urb->status is set when endpoint csr RXSTALL, H_ERROR, DATAERROR or
INCOMPRX bit is set. Those bits mean a broken pipe, so don't start next
urb when any of these bits is set by checking urb->status.

To minimize the risk of regression, only do so for RX, until we have a
test case to understand the behavior of TX.

The patch fixes system freeze issue caused by repeatedly invoking RX ISR
while removing a usb uart device connected to a hub, in which case the
hub has no chance to report the disconnect event due to the kernel is
busy in processing the RX interrupt flooding.

Fix checkpatch complaint (qh != NULL) as while.
Reported-by: NMax Uvarov <muvarov@gmail.com>
Tested-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The MUSB Programming Guide states that the driver should clear RXCSR
bit2 when the controller sets the bit.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.

Tests on another motherboard show that it does work with streams disabled.

Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Several people have reported that UBSAN doesn't like the pointer
arithmetic in ehci_hub_control():

	u32 __iomem	*status_reg = &ehci->regs->port_status[
				(wIndex & 0xff) - 1];
	u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[(wIndex & 0xff) - 1];

If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains.

According to the C standard, pointer computations leading to locations
outside the bounds of an array object (other than 1 position past the
end) are undefined.  In this case, the compiler would be justified in
concluding the wIndex can never be 0 and then optimizing away the
tests for !wIndex that occur later in the subroutine.  (Although,
since ehci->regs->port_status and ehci->regs->hostpc are both 0-length
arrays and are thus GCC extensions to the C standard, it's not clear
what the compiler is really allowed to do.)

At any rate, we can avoid all these difficulties, at the cost of
making the code slightly longer, by not decrementing the index when it
is equal to 0.  The runtime effect is minimal, and anyway
ehci_hub_control() is not on a hot path.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NValdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: NMeelis Roos <mroos@linux.ee>
Reported-by: NMartin_MOKREJÅ <mmokrejs@gmail.com>
Reported-by: N"Navin P.S" <navinp1912@gmail.com>
CC: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 198de51d ("USB: uas: Limit qdepth at the scsi-host level")
removed the scsi_change_queue_depth() call from uas_slave_configure()
assuming that the slave would inherit the host's queue_depth, which
that commit sets to the same value.

This is incorrect, without the scsi_change_queue_depth() call the slave's
queue_depth defaults to 1, introducing a performance regression.

This commit restores the call, fixing the performance regression.

Cc: stable@vger.kernel.org
Fixes: 198de51d ("USB: uas: Limit qdepth at the scsi-host level")
Reported-by: NTom Yan <tom.ty89@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>