Rather than using the compile-time constant CLOCK_TICK_RATE, select
the clock tick rate at run time.  We organise the selection so that
PXA3 automatically falls out with the right tick rate.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The previous implementation was relying on compile time optimizations
based on a constant clock rate.  However, support for different PXA
flavors in the same kernel binary requires that the clock be selected at
run time, so here it is.

Let's move this code to a more appropriate location while at it.
Signed-off-by: NNicolas Pitre <npitre@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
  [POWERPC] Add memchr() to the bootwrapper
  [POWERPC] Implement logging of unhandled signals
  [POWERPC] Add legacy serial support for OPB with flattened device tree
  [POWERPC] Use 1TB segments
  [POWERPC] XilinxFB: Allow fixed framebuffer base address
  [POWERPC] XilinxFB: Add support for custom screen resolution
  [POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
  [POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
  [POWERPC] 4xx: Kilauea defconfig file
  [POWERPC] 4xx: Kilauea DTS
  [POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
  [POWERPC] 4xx: Add AMCC 405EX support to cputable.c
  [POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
  [POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
  [POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
  [POWERPC] 85xx: Killed <asm/mpc85xx.h>
  [POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
  [POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
  [POWERPC] mpc8272ads: Remove muram from the CPM reg property.
  [POWERPC] Make clockevents work on PPC601 processors
  ...

Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.

* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] sata_mv: more S/G fixes

* corruption fix: we only want the lower 16 bits of length (0 == 64kb)

* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
  so we must reset it to own hw-specific length.

* delete unused mv_fill_sg() return value
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a memchr() implementation to the bootwrapper, which will
be needed when libfdt is merged in.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Implement show_unhandled_signals sysctl + support to print when a process
is killed due to unhandled signals just as i386 and x86_64 does.

Default to having it off, unlike x86 that defaults on.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently find_legacy_serial_ports() can find no serial ports on the
OPB with flattened device tree.  Thus no legacy boot console can be
initialized.  Just the early udbg console works, which is initialized
with udbg_init_44x_as1 on the UART's physical address specified in
kernel config.  This happens because we look for ns16750 serial
devices only and expect opb node to have a device type property.  This
patch makes it look for ns16550-compatible devices and use
of_device_is_compatible() for opb in case device type is not
specified.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This makes the kernel use 1TB segments for all kernel mappings and for
user addresses of 1TB and above, on machines which support them
(currently POWER5+, POWER6 and PA6T).

We detect that the machine supports 1TB segments by looking at the
ibm,processor-segment-sizes property in the device tree.

We don't currently use 1TB segments for user addresses < 1T, since
that would effectively prevent 32-bit processes from using huge pages
unless we also had a way to revert to using 256MB segments.  That
would be possible but would involve extra complications (such as
keeping track of which segment size was used when HPTEs were inserted)
and is not addressed here.

Parts of this patch were originally written by Ben Herrenschmidt.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Allow a fixed framebuffer address to be assigned to the framebuffer device
instead of allocating the framebuffer from the consistent memory pool.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some custom implementations of the xilinx fb can use resolutions other
than 640x480.  This patch allows the resolution to be specified in the
device tree or the xilinx_platform_data structure.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The call to xilinxfb_assign is getting unwieldy when adding features
to the Xilinx framebuffer driver.  Change xilinxfb_assign() to accept
a pointer to a xilinxfb_platform_data structure to prepare for adding
additition configuration options.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add 64-bit physical address support to setup_indirect_pci().
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
  mlx4_core: Fix section mismatches
  IPoIB: Allow setting policy to ignore multicast groups
  IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
  IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
  IB/ipath: Remove redundant link state checks
  IB/ipath: Fix IB_EVENT_PORT_ERR event
  IB/ipath: Better handling of unexpected GPIO interrupts
  IB/ipath: Maintain active time on all chips
  IB/ipath: Fix QHT7040 serial number check
  IB/ipath: Indicate a couple of chip bugs to userspace
  IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
  IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
  IB/ipath: Remove duplicate copy of LMC
  IB/ipath: Add ability to set the LMC via the sysfs debugging interface
  IB/ipath: Optimize completion queue entry insertion and polling
  IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
  IB/ipath: Generate flush CQE when QP is in error state
  IB/ipath: Remove redundant code
  IB/ipath: Future proof eeprom checksum code (contents reading)
  IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
  [SKY2]: status polling loop (post merge)
  [NET]: Fix NAPI completion handling in some drivers.
  [TCP]: Limit processing lost_retrans loop to work-to-do cases
  [TCP]: Fix lost_retrans loop vs fastpath problems
  [TCP]: No need to re-count fackets_out/sacked_out at RTO
  [TCP]: Extract tcp_match_queue_to_sack from sacktag code
  [TCP]: Kill almost unused variable pcount from sacktag
  [TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
  [TCP]: Add bytes_acked (ABC) clearing to FRTO too
  [IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
  [NETFILTER]: x_tables: add missing ip6t_modulename aliases
  [NETFILTER]: nf_conntrack_tcp: fix connection reopening
  [QETH]: fix qeth_main.c
  [NETLINK]: fib_frontend build fixes
  [IPv6]: Export userland ND options through netlink (RDNSS support)
  [9P]: build fix with !CONFIG_SYSCTL
  [NET]: Fix dev_put() and dev_hold() comments
  [NET]: make netlink user -> kernel interface synchronious
  [NET]: unify netlink kernel socket recognition
  [NET]: cleanup 3rd argument in netlink_sendskb
  ...

Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.

(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (80 commits)
  [MIPS] tlbex.c: Cleanup __init usage.
  [MIPS] WRPPMC serial support move to platform device
  [MIPS] R1: Fix hazard barriers to make kernels work on R2 also.
  [MIPS] VPE: reimplement ELF loader.
  [MIPS] cleanup WRPPMC include files
  [MIPS] Add BUG_ON assertion for attempt to run kernel on the wrong CPU type.
  [MIPS] SMP: Use ISO C struct initializer for local structs.
  [MIPS] SMP: Kill useless casts.
  [MIPS] Kill num_online_cpus() loops.
  [MIPS] SMP: Implement smp_call_function_mask().
  [MIPS] Make facility to convert CPU types to strings generally available.
  [MIPS] Convert list of CPU types from #define to enum.
  [MIPS] Optimize get_unaligned / put_unaligned implementations.
  [MIPS] checkfiles: Fix "need space after that ','" errors.
  [MIPS] Fix "no space between function name and open parenthesis" warnings.
  [MIPS] Allow hardwiring of the CPU type to a single type for optimization.
  [MIPS] tlbex: Size optimize code by declaring a few functions inline.
  [MIPS] pg-r4k.c: Dump the generated code
  [MIPS] Cobalt: Remove cobalt_machine_power_off()
  [MIPS] Cobalt: Move reset port definition to arch/mips/cobalt/reset.c
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits)
  ide: use only ->set_pio_mode method for programming PIO modes (take 2)
  sis5513: don't change UDMA settings when programming PIO
  it8213/piix/slc90e66: don't change DMA settings when programming PIO
  alim15x3: PIO mode setup fixes
  siimage: fix ->set_pio_mode method to select PIO data transfer
  cs5520: don't enable VDMA in ->speedproc
  sc1200: remove redundant warning message from sc1200_tune_chipset()
  ide-pmac: PIO mode setup fixes (take 3)
  icside: fix ->speedproc to return on unsupported modes (take 5)
  sgiioc4: use ide_tune_dma()
  amd74xx/via82cxxx: use ide_tune_dma()
  ide: add ide_set{_max}_pio() (take 4)
  ide: Kconfig face-lift
  ide: move ide_rate_filter() calls to the upper layer (take 2)
  sis5513: add ->udma_filter method for chipset_family >= ATA_133
  ide: mode limiting fixes for user requested speed changes
  ide: add missing ide_rate_filter() calls to ->speedproc()-s
  ide: call udma_filter() before resorting to the UltraDMA mask
  ide: make jmicron match vendor and device class
  pdc202xx_new: switch to using pci_get_slot() (take 2)
  ...

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
  leds: Update Cobalt Qube series front LED support
  leds: Add Cobalt Raq series LEDs support
  leds: Rename leds-cobalt driver

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
  backlight: Convert corgi backlight driver into a more generic driver
  backlight: Add Samsung LTV350QV LCD driver
  backlight: Fix cr_bllcd allocations and error paths
  backlight/leds: Make two structs static

* 'dmi-const' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  drivers/firmware: const-ify DMI API and internals

* 'block-2.6.24' of git://git.kernel.dk/data/git/linux-2.6-block: (37 commits)
  [BLOCK] Fix failing compile with BLK_DEV_IO_TRACE=n
  compat_ioctl: move floppy handlers to block/compat_ioctl.c
  compat_ioctl: move cdrom handlers to block/compat_ioctl.c
  compat_ioctl: move BLKPG handling to block/compat_ioctl.c
  compat_ioctl: move hdio calls to block/compat_ioctl.c
  compat_ioctl: handle blk_trace ioctls
  compat_ioctl: add compat_blkdev_driver_ioctl()
  compat_ioctl: move common block ioctls to compat_blkdev_ioctl
  Sysace: Don't enable IRQ until after interrupt handler is registered
  Sysace: sparse fixes
  Sysace: Minor coding convention fixup
  drivers/block/umem: use DRIVER_NAME where appropriate
  drivers/block/umem: trim trailing whitespace
  drivers/block/umem: minor cleanups
  drivers/block/umem: use dev_printk()
  drivers/block/umem: move private include away from include/linux
  Sysace: Labels in C code should not be indented.
  Sysace: Add of_platform_bus binding
  Sysace: Move IRQ handler registration to occur after FSM is initialized
  Sysace: minor rework and cleanup changes
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  [AVR32] Fix random segfault with preemption
  [AVR32] Don't use __builtin_xchg()
  [AVR32] ngw100 i2c-gpio tweaks
  [AVR32] Ignore a few irrelevant syscalls
  [AVR32] SMC configuration in clock cycles
  [AVR32] Drop support for redundant "keepinitrd" boot-time parm.
  [AVR32] Make dma_sync_*_for_cpu no-ops
  [AVR32] Remove unneeded 8K alignment of .text section
  [AVR32] Kill a few hardcoded constants in vmlinux.lds
  [AVR32] rename vmlinux.lds
  [AVR32] fix command line parsing in early_parse_fbmem
  [AVR32] checkstack support
  [AVR32] Wire up USBA device
  [AVR32] add multidrive support for pio driver
  [AVR32] /sys/kernel/debug/at32ap_clk
  [AVR32] Move AT32_PM_BASE definition into pm.h

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (74 commits)
  Blackfin serial driver: pending a unique anomaly id, tie the break flood issue to ANOMALY_05000230
  blackfin enable arbitary speed serial setting
  Blackfin arch: Remove cruft - CONFIG_DEBUG_SERIAL_EARLY_INIT and DEBUG_KERNEL_START
  Blackfin arch: fix typo in register name
  Blackfin arch: trim the Blackfin arch MAINTAINERS list
  Blackfin arch: fix bug libstdc++ calling writev with an iovec containing { NULL, 0 } fails on Blackfin
  Blackfin arch: Export strcpy - occasionally get module link failures otherwise
  Blackfin arch: the load address is not safe to point to as a workaround for ANOMALY 05000281
  Blackfin arch: show_mem can not be marked as init, since it is called during OOM condition
  Blackfin arch: flush/inv the correct range when using write back cache and fix bugs find by dmacopy
  Blackfin arch: update kgdb patch
  Blackfin arch: Comply with revised Anomaly Workarounds for BF533 05000311 and BF561 05000323
  Blackfin arch: Print out debug info, as early as possible
  Blackfin arch: Enable earlyprintk earlier - so any error after our interrupt tables are set up will print out
  Blackfin arch: fix endless loop bug when a double fault happens
  Blackfin arch: Initial patch to add earlyprintk support
  Blackfin arch: add TWIx_REGBASE and SPIx_REGBASE to specific CPU header files, use the new REGBASE for board platform resources
  Blackfin arch: modify the insX/outsX and dma_insX/dma_outsX to be compatible with other archs
  Blackfin arch: add more common defines for output sections
  Blackfin arch: cleanup IO and DMA_IO API function definitions according to other arches
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (310 commits)
  V4L/DVB (6316): Change list_for_each+list_entry to list_for_each_entry
  V4L/DVB (6315): pvrusb2: Change list_for_each+list_entry to list_for_each_entry
  V4L/DVB (6314): saa7134: Replace list_for_each+list_entry with list_for_each_entry
  V4L/DVB (6313): ivtv: Replace list_for_each+list_entry with list_for_each_entry
  V4L/DVB (6312): cx88: Replace list_for_each+list_entry with list_for_each_entry
  V4L/DVB (6311): dvb: Replace list_for_each+list_entry with list_for_each_entry
  V4L/DVB (6308): V4L: zc0301, remove bad usage of ERESTARTSYS
  V4L/DVB (6307): V4L: w9968cf, remove bad usage of ERESTARTSYS
  V4L/DVB (6306): Few clenups for saa7134 resume code
  V4L/DVB (6305): V4L: videobuf-core.c avoid NULL dereferences in videobuf-core
  V4L/DVB (6301): pvrusb: Update DEBUGIFC sysfs to kernel 2.6.13+
  V4L/DVB (6300): CodingStyle cleanup
  V4L/DVB (6299): dvb: Add dependencies for VIDEOBUF_DVB
  V4L/DVB (6297): cx23885: remove wrong Kconfig selection of VIDEOBUF
  V4L/DVB (6296): dib0700: add support for AverMedia DVB-T Express card
  V4L/DVB (6295): saa7134: add autodetection for KWorld ATSC-115
  V4L/DVB (6293): V4L: convert struct class_device to struct device
  V4L/DVB (6292): videobuf_core init always require callback implementation
  V4L/DVB (6291): Fix: avoid oops on some SMP machines
  V4L/DVB (6290): remove videobuf_set_pci_ops
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (67 commits)
  mmc: don't use weight32()
  pxamci: support arbitrary block size
  sdio: make the IRQ thread more resilient in the presence of bad states
  sdio: fix IRQ diagnostic message
  sdhci: remove old dma module params
  sdhci: add SDHCI_QUIRK_BROKEN_DMA quirk
  sdhci: remove DMA capability check from controller's PCI Class reg
  sdhci: fix a typo
  mmc: Disabler for Ricoh MMC controller
  sdio: adaptive interrupt polling
  mmc: pxamci: add SDIO card interrupt reporting capability
  mmc: pxamci: set proper buswidth capabilities according to PXA flavor
  mmc: pxamci: set proper block capabilities according to PXA flavor
  mmc: pxamci: better pending IRQ determination
  arm: i.MX/MX1 SDHC implements SD cards read-only switch read-back
  mmc: add led trigger
  mmc_spi host driver
  MMC core learns about SPI
  MMC/SD card driver learns SPI
  MMC headers learn about SPI
  ...

Handle the corner case where budget is exhausted correctly.
And save unnecessary read of index register.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():

		/* Drivers must not modify the NAPI state if they
		 * consume the entire weight.  In such cases this code
		 * still "owns" the NAPI instance and therefore can
		 * move the instance around on the list at-will.
		 */

A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.

BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addition of lost_retrans_low to tcp_sock might be
unnecessary, it's not clear how often lost_retrans worker is
executed when there wasn't work to do.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detection implemented with lost_retrans must work also when
fastpath is taken, yet most of the queue is skipped including
(very likely) those retransmitted skb's we're interested in.
This problem appeared when the hints got added, which removed
a need to always walk over the whole write queue head.
Therefore decicion for the lost_retrans worker loop entry must
be separated from the sacktag processing more than it was
necessary before.

It turns out to be problematic to optimize the worker loop
very heavily because ack_seqs of skb may have a number of
discontinuity points. Maybe similar approach as currently is
implemented could be attempted but that's becoming more and
more complex because the trend is towards less skb walking
in sacktag marker. Trying a simple work until all rexmitted
skbs heve been processed approach.

Maybe after(highest_sack_end_seq, tp->high_seq) checking is not
sufficiently accurate and causes entry too often in no-work-to-do
cases. Since that's not known, I've separated solution to that
from this patch.

Noticed because of report against a related problem from TAKANO
Ryousei <takano@axe-inc.co.jp>. He also provided a patch to
that part of the problem. This patch includes solution to it
(though this patch has to use somewhat different placement).
TAKANO's description and patch is available here:

  http://marc.info/?l=linux-netdev&m=119149311913288&w=2

...In short, TAKANO's problem is that end_seq the loop is using
not necessarily the largest SACK block's end_seq because the
current ACK may still have higher SACK blocks which are later
by the loop.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both sacked_out and fackets_out are directly known from how
parameter. Since fackets_out is accurate, there's no need for
recounting (sacked_out was previously unnecessarily counted
in the loop anyway).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is necessary for upcoming DSACK bugfix. Reduces sacktag
length which is not very sad thing at all... :-)

Notice that there's a need to handle out-of-mem at caller's
place.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's on the way for future cutting of that function.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This condition (plain R) can arise at least in recovery that
is triggered after tcp_undo_loss. There isn't any reason why
they should not be marked as lost, not marking makes in_flight
estimator to return too large values.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I was reading tcp_enter_loss while looking for Cedric's bug and
noticed bytes_acked adjustment is missing from FRTO side.

Since bytes_acked will only be used in tcp_cong_avoid, I think
it's safe to assume RTO would be spurious. During FRTO cwnd
will be not controlled by tcp_cong_avoid and if FRTO calls for
conventional recovery, cwnd is adjusted and the result of wrong
assumption is cleared from bytes_acked. If RTO was in fact
spurious, we did normal ABC already and can continue without
any additional adjustments.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-2.6.24' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into for-2.6.24

Signed-off-by: NFranck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Tested with Malta; inflates malta_defconfig by 3932 bytes.  Ideally there
should be additional configuration to allow getting rid of this overhead
but that would be too much complexity at this stage of the release cycle.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Loading ELF binaries based on the section table is totally wrong.  This
still leaves the other fat bug of referencing symbols in an executable
unfixed, so people better don't run strip on their binaries ...

As added bonus the new loader is also 23 lines shorter.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>