None of the platforms are actually using the SoC device so remove it
(only atmel actually has a suspend method).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is in preparation for the removal of struct snd_soc_device.

The pop time configuration should really be a property of the card not
the codec but since DAPM currently uses the codec rather than the card
using the codec is fine for now.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

- Add aic3x_set_headset_detection() function to define the headset
  detection mode for tlv32aic3x chips
- added aic3x_button_pressed()
- Read from the real-time registers in aic3x_headset_detected() to query
  headset presence without an occured interrupt
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The TWL4030 codec device has two ADCs. Both of them can have
several inputs routed to them, but TRM says that only one source
can be selected for every ADC, even though every source has a
dedicated bit in the registers.

This patch adds input source controls. It modifies default register
values to have no inputs selected and ADCs disabled. When some
input is selected, control handlers enable apropriate input
amplifier and ADC. If a microphone is selected, bias power is
automatically enabled. When some input is deselected, unused
chip parts are disabled.

Microphone and line input recording tested on OMAP3 pandora board.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As part of the deprecation of snd_soc_device push the registration of
the platform down into the card structure.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

ASoC v2 does not use the struct snd_soc_device at runtime, using struct
snd_soc_card as the root of the card.  Begin removing data from
snd_soc_device by pushing the workqueue data into snd_soc_card, using a
backpointer to the snd_soc_device to keep things going for the time
being.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All outputs have dedicated gain controls except the
HandsFree output.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add Playback volume controls for all four DACs.
All four paths has three levels of volume controls:
Digital Fine gain, Digital Coarse gain, Analog gain.

The controls are named to reflect their connection to the DACs.
Per DAC volume can be performed, if needed:
amixer sset 'DAC1 Analog'  5,10
DACL1 analog gain to 5
DACR1 analog gain to 10
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The digital Capture gain control has a range:
0 to 31 dB in 1 dB steps.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently ASoC card initialisation is completed by a function called
snd_soc_register_card().  As part of the work to allow independant
registration of cards, codecs and machines in ASoC v2 a new function of
the same name has been added so rename the existing function to
facilitate the merge of v2.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix the old-style trigger callback in s3c2443-ac97.c:
    sound/soc/s3c24xx/s3c2443-ac97.c:378: warning: initialization from incompatible pointer type
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the wrong shutdown callback type.  Also removed the unused variables
there:

  sound/soc/pxa/corgi.c: In function 'corgi_shutdown':
  sound/soc/pxa/corgi.c:114: warning: unused variable 'codec'
  sound/soc/pxa/corgi.c: At top level:
  sound/soc/pxa/corgi.c:175: warning: initialization from incompatible pointer type
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This reverts commit 9171e5e6.

I can't reproduce the compile warnings any more.  The warnings
might be some weird cross-compiling set up.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The dependency on SND_SOC is already fulfilled in sound/soc/Kconfig,
thus no more need in Kconfig of each sub directory.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Apple ALU wireless keyboards are bluetooth devices
  HID: remove setup mutex, fix possible deadlock
  HID: add USB ID for another dual gameron adapter
  HID: unignore mouse on unibody macbooks
  HID: fix blacklist entries for greenasia/pantherlord

We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: NKevin Hao <kexin.hao@windriver.com>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When no console is configured tty_open tries to call kref_get on a NULL
pointer, return ENODEV instead.
Signed-off-by: NWill Newton <will.newton@gmail.com>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: serial: add more Onda device ids to option driver
  USB: usb-storage: unusual_devs entry for Nikon D2H
  USB: storage: unusual_devs entry for Mio C520-GPS
  USB: fsl_usb2_udc: Report disconnect before unbinding
  USB: fsl_qe_udc: Report disconnect before unbinding
  USB: fix SB600 USB subsystem hang bug
  Revert "USB: improve ehci_watchdog's side effect in CPU power management"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Fix build for 32-bit SMP configs

The zone's rotation statistics must not be accessed without the
corresponding LRU lock held.  Fix an unprotected write in
shrink_active_list().
Acked-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NJohannes Weiner <hannes@saeurebad.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit e669dae6, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.
Requested-by: NDavid Miller <davem@davemloft.net>
Acked-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Hide annoying uninitialized warnings:
  sound/soc/codecs/wm8903.c:382: warning: ‘reg’ may be used uninitialized in this function
  sound/soc/codecs/wm8903.c:383: warning: ‘shift’ may be used uninitialized in this function
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Thanks to Domenico Riccio for pointing these out.

Cc: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds an unusual_devs entry for the Nikon D2H camera.

From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit.  Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.

This fixes Bugzilla #11583.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NTamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding.

The patch fixes following badness:

root@b1:~# insmod fsl_usb2_udc.ko
Freescale High-Speed USB SOC Device Controller driver (Apr 20, 2007)
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC 26:07:ba:c0:44:33
usb0: HOST MAC 96:81:0c:05:4d:e3
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl-usb2-udc: bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [e10c3454] composite_unbind+0x24/0x15c [g_ether]
LR [e10aa454] usb_gadget_unregister_driver+0x13c/0x164 [fsl_usb2_udc]
Call Trace:
[df145e80] [ffffff94] 0xffffff94 (unreliable)
[df145eb0] [e10aa454] usb_gadget_unregister_driver+0x13c/0x164 [fsl_usb2_udc]
[df145ed0] [e10c4c40] usb_composite_unregister+0x3c/0x4c [g_ether]
[df145ee0] [c006bcc0] sys_delete_module+0x130/0x19c
[df145f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
unregistered gadget driver 'g_ether'
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding. This also fixes
muram memory leak, since we free muram in the qe_ep_disable().

But mainly the patch fixes following badness:

root@b1:~# insmod fsl_qe_udc.ko
fsl_qe_udc: Freescale QE/CPM USB Device Controller driver, 1.0
fsl_qe_udc e01006c0.usb: QE USB controller initialized as device
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC be:2d:3c:fa:be:f0
usb0: HOST MAC 62:b8:6a:df:38:66
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl_qe_udc e01006c0.usb: fsl_qe_udc bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [d10c1374] composite_unbind+0x24/0x15c [g_ether]
LR [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
Call Trace:
[cfb93e80] [cfb1f3a0] 0xcfb1f3a0 (unreliable)
[cfb93eb0] [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
[cfb93ed0] [d10c2a3c] usb_composite_unregister+0x3c/0x4c [g_ether]
[cfb93ee0] [c006bde0] sys_delete_module+0x130/0x19c
[cfb93f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
fsl_qe_udc e01006c0.usb: unregistered gadget driver 'g_ether'
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is required for all AMD SB600 revisions to avoid USB subsystem hang
symptom. The USB subsystem hang symptom is observed when the system has
multiple USB devices connected to it. In some cases a USB hub may be required
to observe this symptom.

Reported in bugzilla as #11599, the similar patch for SB700 old revision is:
commit b09bc6cbReported-by: Nraffaele <ralfconn@tele2.it>
Tested-by: NRoman Mamedov <roman@rm.pp.ru>
Signed-off-by: NShane Huang <shane.huang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit f0d781d5.

It was the wrong thing to do, and does not really do what it said
it did.

Cc: Yi Yang <yi.y.yang@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

attr_smt_snooze_delay is only defined for CONFIG_PPC64, so protect the
attribute removal with the same condition.  This fixes this build error
on 32-bit SMP configurations:

/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c: In function ‘unregister_cpu_online’:
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: ‘attr_smt_snooze_delay’ undeclared (first use in this function)
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: (Each undeclared identifier is reported only once
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: for each function it appears in.)
Signed-off-by: NPaul Mackerras <paulus@samba.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Fix copy'n'pasteo that broke VT switch if flushing was non-empty.

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Fix system calls on Cell entered with XER.SO=1
  powerpc/cell: Fix GDB watchpoints, again
  powerpc/mpic: Don't reset affinity for secondary MPIC on boot
  powerpc/cell/axon-msi: Retry on missing interrupt
  powerpc: Fix boot freeze on machine with empty memory node
  powerpc: Fix IRQ assignment for some PCIe devices
  powerpc/spufs: Fix spinning in spufs_ps_fault on signal
  powerpc/mpc832x_rdb: fix swapped ethernet ids
  powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
  powerpc/85xx: L2 cache size wrong in 8572DS dts
  powerpc/virtex: Update defconfigs
  powerpc/52xx: update defconfigs
  xsysace: Fix driver to use resource_size_t instead of unsigned long
  powerpc/virtex: fix various format/casting printk mismatches
  powerpc/mpc5200: fix bestcomm Kconfig dependencies
  powerpc/44x: Fix 460EX/460GT machine check handling
  powerpc/40x: Limit allocable DRAM during early mapping

* master.kernel.org:/home/rmk/linux-2.6-arm:
  Allow architectures to override copy_user_highpage()
  [ARM] pxa/palmtx: misc fixes to use generic GPIO API
  ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling
  [ARM] pxa/corgi: update default config to exclude tosa from being built
  [ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
  ARM: OMAP: Typo fix for clock_allow_idle
  ARM: OMAP: Remove broken LCD driver for SX1
  [ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0
  [ARM] pxa/MioA701: bluetooth resume fix
  [ARM] pxa/MioA701: fix memory corruption.

Introduced in the "Avoid BUG_ONs on VT switch" commit.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>