The code can be symmetrical so make it so. This
makes it easier to understand and work with.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It doesn't make much sense to reconfigure peer
completely upon reassociation. This will make it
easier to have a more uniform association code
across different modes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There's no need to pass bss_conf explicitly as it
is accessible via vif pointer. This requires
slight changes in function prototypes. While at it
clean up listen interval workaround/command.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A frequent request have been to be able to provide calibration data from a
file as some of the AP devices store the calibration data on an MTD partition.
This patchset adds support for that and also makes it easier to add Device Tree
support later on.

The calibration data is found by using the id string provided by dev_name()
using this format:

cal-<bus>-<id>.bin

With PCI the id string contains bus, slot and func values. For example for a
PCI device in bus 2 slot 0, ath10k will try to retrieve a calibration data from
a file:

/lib/firmware/ath10k/cal-pci-0000:02:00.0.bin

The calibration data sequence is:

1. Check with request_firmware() if there's a calibration file
   ("cal-<bus>-<id>.bin") on the filesystem for this device. If yes, use that. If
   not, goto 2

2. Check if otp.bin is able to successfully load the calibration data
   from OTP. If yes, use that. If not, goto 3.

4. Print an error message that no calibration data found and stop driver
   initialization for this device.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is preparation for being able to download calibration data from a file.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit 3a0861ff ("ath10k: remove ath10k_bus") removed enum ath10k_bus
because it was not used for anything at the time. But now it's needed for for
retrieving the right calibration data file so add it back. Only new addition is
ath10k_bus_str().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Based on GFP flag given to DMA coherent allocation, the behaviour of
dma_free_coherent is changed. This behavioural diffrence is noticeable
in ARM platform. If DMA memory is allocated with GFP_KERNEL, free
coherent can not be called inside spin lock. This is causing kernel
crash in ARM platforms. Fix this by changing GFP flag to atomic.

This is most likely a regression from commit 64badcb6 ("ath10k: workaround
fw beaconing bug").

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add tracing support to forward management and data frames to
user space for packet inspection.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix WMI scan command length we setup when scan request.

This fix issue with 636 firmware when scan always failed
with message:

ath10k_pci 0000:02:00.0: wmi start scan
ath10k_pci 0000:02:00.0: wmi stop scan reqid 1 req_type 0 vdev/scan_id 0
ath10k_pci 0000:02:00.0: failed to stop wmi scan: -11
ath10k_pci 0000:02:00.0: failed to stop scan: -11
ath10k_pci 0000:02:00.0: failed to start hw scan: -110
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is required if we take into account possibility to load the driver
from initrd (RAM disk), so in other words: very early in the boot process,
before the file system is visible.

In such case we need to have the firmware files accessible from ram disk too,
and this patch guarantee this.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's not really necessary to create bssid peer for
bssid. Self-address peer is sufficient.

This prevents some firmware revisions from crashing.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It makes a lot more sense to print these kinds of
problems as a warning instead of a debug.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The tx info such as msdu_id, frame len, vdev id and tid are reported
to user space by tracepoint. This is useful for collecting tx
statistics.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Upon the reception of frame, the descriptor status are reported
to user space by tracepoint. This is useful for collecting rx
statistics.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is useful for collecting pktlog statistics of tx, rx
and rate information, so add tracing for the API call.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add support to configure packet log filters (tx, rx, rate control)
via debugfs. To disable htt pktlog events set the filters to 0.

ex:

To enable pktlog for all filters

   echo 0x1f > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter

To disable pktlog

   echo 0 > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This can allow more than 32 stations to be supported
without over-running the bitmap.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add support for reading firmware stats through the ethtool
API.  This may be easier for applications to manipulate
compared to parsing a text based debugfs file.

kvalo: remove unneeded ifdefs, call ath10k_debug_fw_stats_request() and added
simple error handling
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add three counters related to firmware crashes or resets.

Usage:

# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_reset_stats
fw_crash_counter                2
fw_warm_reset_counter           43
fw_cold_reset_counter           0
#

kvalo: split into it's own patch, add debugfs file and add locking
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If stat data exceeds wmi-htc buffer limits
firmware splits it into many wmi stats update
events which are delivered in a ping-pong fashion
triggered by wmi stats request command.

Since there's only an implicit start-of-data and
no end-of-data indications the driver has to
perform some trickery to get complete stat data.

kvalo: use %zu to fix a compiler warning and fix a typo in a comment
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Stats were requested and processed for each read
call. This caused inconsistent readings.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The naming was a bit inconsistent.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The parsing function was rather complex. Simplify
by splitting it up into firmware branch specific
implementations.

While at it move the parsing code into wmi.c where
it belongs.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The return values are not used by callers of these functions
so change the functions to return void.

Other miscellanea:

o add __printf verification to wil6210 logging functions
  No format/argument mismatches found
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Provide calibration data used by the firmware to user space via a debugfs file.
This makes it easier to debug calibration related problems.

Example:

sudo cp /sys/kernel/debug/ieee80211/phy0/ath10k/cal_data 1.cal
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

diag_read() is used for reading from firmware memory via the diagnose window.
First user will be cal_data debugfs file.

To serialise diagnostic window access and make it safe to use while firmware is
running take ce_lock both in ath10k_pci_diag_write_mem() and
ath10k_pci_diag_read_mem(). Because of that all the CE calls had to be changed
to _nolock variants.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The diagnostic window (CE7) uses polling and is not initiliased to retrieve
interrupts so disable interrupts altogether for CE7. Otherwise ath10k crashes
when using the diagnostic window while the firmware is running due to NULL
dereference and polling reads timeout.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it easier to debug the device-target
communication at a very low level.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it easier to debug hex dumps on systems
with more than a single ath10k device.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HTT version is already printed so print WMI
version as well for consistency.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This gets rid of the ugly scan structure building
and uses a saner way to do it.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make all wmi event functions match the same naming
style, i.e. ath10k_wmi_event_<name>.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make the phyerr structures more compact and easier
to understand. Also add constness.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The logic responsible for processing the event is
no different across different firmware binaries.
The difference that needs to be dealt with is the
ABI of data structures.

The intermediate structure uses __le32 to avoid
extra memory allocations to byteswap
variable-length substructures (i.e. host mem
chunks).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Init functions should be placed at the end of
files in most cases to avoid forward declarations
for static functions.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Simplify the code by deduplicating structure
definitions and code.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The structure is being set up in 2 places.
Deduplicate the code by creating a helper.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This command is not used anymore and most firmware
revisions do not seem to handle it well. Channel
switching is done via vdev restarting.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware reports the number of RF chains so use
that for initialization of supp_{tx,rx}_chainmask
instead of using a macro for 3x3 chips.

This should make tx/rx chainmask reports correct
for chips other than 3x3.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions don't wait for beacon tx
completion before sending another SWBA event. This
could lead to hardware using old (freed) beacon
data in some cases, e.g. tx credit starvation
combined with missed TBTT. This is very very rare.

On non-IOMMU-enabled hosts this could be a
possible security issue because hw could beacon
some random data on the air.  On IOMMU-enabled
hosts DMAR faults would occur in most cases and
target device would crash.

Since there are no beacon tx completions (implicit
nor explicit) propagated to host the only
workaround for this is to allocate a DMA-coherent
buffer for a lifetime of a vif and use it for all
beacon tx commands. Worst case for this approach
is some beacons may become corrupted, e.g. garbled
IEs or out-of-date TIM bitmap.

Keep the original beacon-related code as-is in
case future firmware revisions solve this problem
so that the old path can be easily re-enabled with
a fw_feature flag.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>