- 10 4月, 2012 5 次提交
-
-
由 Johannes Berg 提交于
Since some of the HT code pre-dates 802.11n-2009 some names are wrong. The one that bothers me most is that "HT operation" is called "HT information" in our code and that causes confusion. Rename "HT information" to "HT operation" and also the control_chan field to primary_chan to match the name used in the spec. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Acked-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Sometimes the probe frame (nullfunc) is stuck at the hw queue. so that the mac80211 terminates the connection as it wont see the tx status. Instead of waiting for long period for ack status, lets call flush to get nullfunc status immediately. It also helps to send the nullfunc till max tries reached. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
There might be latency at AP side to update TIM IE which could cause the station to send pspoll frame even after the wakeup. If the powersave is disabled, the nullfunc notification alone is sufficient to receive frames from the AP. And if the pspoll frame was already sent, no need to resend the frame till it was acked by AP. Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
In the experiment with Azimuth ADEPT-n testbed where the APs transmit power was reduced to 25% and the signal strength was futher attenuated by 20dB and induced a path loss of ~7dB, the station was reporting beacon losses and the following issue were observed. * rx clear is stuck at low for more than 300ms * dcu chain and complete state is stuck at one of the hang signature This patch triggers the hang detection logic that recovers the chip from any of the above conditions. As the issue was originally reported in ChromeOs with AR9382 chips, this detection logic is enabled only for AR9380/2 chips. Cc: Paul Stewart <pstew@google.com> Reported-by: NGary Morain <gmorain@google.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
This patch improves ANI operations by switching among the immunity levels based on PHY errors and beacon rssi which will adjust receiver desensitizing parameters. The changes are * Configure the Weak Signal Detection based on current immunity value. * At highest OFDM immunity level poor performance was observed with strong interference. By tuning the FIR step and spur immunity levels and not changing any weak signal detection thresholds at any level helped to improve the performance. * ANI took long time to recover back to lower immunity levels on heavy data load. As the listen time got reset to zero before reaching to the 5x of aniperiod, the immunity level is not lowering back even without any interference. This patch fix that. Cc: Paul Stewart <pstew@google.com> Cc: Susinder Gulasekaran <susinder@qca.qualcomm.com> Signed-off-by: NSuresh Chandrasekaran <csuresh@qca.qualcomm.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 3月, 2012 13 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: 1) Name string overrun fix in gianfar driver from Joe Perches. 2) VHOST bug fixes from Michael S. Tsirkin and Nadav Har'El 3) Fix dependencies on xt_LOG netfilter module, from Pablo Neira Ayuso. 4) Fix RCU locking in xt_CT, also from Pablo Neira Ayuso. 5) Add a parameter to skb_add_rx_frag() so we can fix the truesize adjustments in the drivers that use it. The individual drivers aren't fixed by this commit, but will be dealt with using follow-on commits. From Eric Dumazet. 6) Add some device IDs to qmi_wwan driver, from Andrew Bird. 7) Fix a potential rcu_read_lock() imbalancein rt6_fill_node(). From Eric Dumazet. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: net: fix a potential rcu_read_lock() imbalance in rt6_fill_node() net: add a truesize parameter to skb_add_rx_frag() gianfar: Fix possible overrun and simplify interrupt name field creation USB: qmi_wwan: Add ZTE (Vodafone) K3570-Z and K3571-Z net interfaces USB: option: Ignore ZTE (Vodafone) K3570/71 net interfaces USB: qmi_wwan: Add ZTE (Vodafone) K3565-Z and K4505-Z net interfaces qlcnic: Bug fix for LRO netfilter: nf_conntrack: permanently attach timeout policy to conntrack netfilter: xt_CT: fix assignation of the generic protocol tracker netfilter: xt_CT: missing rcu_read_lock section in timeout assignment netfilter: cttimeout: fix dependency with l4protocol conntrack module netfilter: xt_LOG: use CONFIG_IP6_NF_IPTABLES instead of CONFIG_IPV6 vhost: fix release path lockdep checks vhost: don't forget to schedule() tools/virtio: stub out strong barriers tools/virtio: add linux/hrtimer.h stub tools/virtio: add linux/module.h stub
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: device tree work" from Arnd Bergmann: "Most of these patches convert code from using static platform data to describing the hardware in the device tree. This is only the first half of the changes for v3.4 because a lot of patches for this topic came in the last week before the merge window. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h} * tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits) Document: devicetree: add OF documents for arch-mmp ARM: dts: append DTS file of pxa168 ARM: mmp: append OF support on pxa168 ARM: mmp: enable rtc clk in pxa168 i2c: pxa: add OF support serial: pxa: add OF support arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board ARM: OMAP2+: Remove extra ifdefs for board-generic ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected ASoC: DT: Add digital microphone binding to PAZ00 board. ARM: dt: Add ARM PMU to tegra*.dtsi ARM: at91: at91sam9x5cm/dt: add leds support ARM: at91: usb_a9g20/dt: add gpio-keys support ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support ARM: at91: at91sam9m10g45ek/dt: add leds support ARM: at91: usb_a9g20/dt: add leds support ARM: at91/pio: add new PIO3 features ARM: at91: add sam9_smc.o to at91sam9x5 build ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter ARM: at91/tc: add device tree support to atmel_tclib ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: driver specific updates" from Arnd Bergmann: "These are all specific to some driver. They are typically the platform side of a change in the drivers directory, such as adding a new driver or extending the interface to the platform. In cases where there is no maintainer for the driver, or the maintainer prefers to have the platform changes in the same branch as the driver changes, the patches to the drivers are included as well. A much smaller set of driver updates that depend on other branches getting merged first will be sent later. The new export of tegra_chip_uid conflicts with other changes in fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with the cleanup of the interrupt handling of that driver. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" Fixed up aforementioned trivial conflicts. * tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits) ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci mmc: sdhci-s3c: add platform data for the second capability ARM: SAMSUNG: support the second capability for samsung-soc ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1 ARM: EXYNOS: Enable MDMA driver regulator: Remove bq24022 regulator driver rtc: sa1100: add OF support pxa: magician/hx4700: Convert to gpio-regulator from bq24022 ARM: OMAP3+: SmartReflex: fix error handling ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API ARM: OMAP3+: SmartReflex: micro-optimization for sanity check ARM: OMAP3+: SmartReflex: misc cleanups ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata() ARM: OMAP3+: hwmod: add SmartReflex IRQs ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register ARM: OMAP3+: SmartReflex: Add a shutdown hook ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP ... Conflicts: arch/arm/mach-tegra/Makefile arch/arm/mach-tegra/fuse.c drivers/rtc/rtc-sa1100.c
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "remoteproc/rpmsg: new subsystem" from Arnd Bergmann: "This new subsystem provides a common way to talk to secondary processors on an SoC, e.g. a DSP, GPU or service processor, using virtio as the transport. In the long run, it should replace a few dozen vendor specific ways to do the same thing, which all never made it into the upstream kernel. There is a broad agreement that rpmsg is the way to go here and several vendors have started working on replacing their own subsystems. Two branches each add one virtio protocol number. Fortunately the numbers were agreed upon in advance, so there are only context changes. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" Fixed up trivial protocol number conflict due to the mentioned additions next to each other. * tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits) remoteproc: cleanup resource table parsing paths remoteproc: remove the hardcoded vring alignment remoteproc/omap: remove the mbox_callback limitation remoteproc: remove the single rpmsg vdev limitation remoteproc: safer boot/shutdown order remoteproc: remoteproc_rpmsg -> remoteproc_virtio remoteproc: resource table overhaul rpmsg: fix build warning when dma_addr_t is 64-bit rpmsg: fix published buffer length in rpmsg_recv_done rpmsg: validate incoming message length before propagating rpmsg: fix name service endpoint leak remoteproc/omap: two Kconfig fixes remoteproc: make sure we're parsing a 32bit firmware remoteproc: s/big switch/lookup table/ remoteproc: bail out if firmware has different endianess remoteproc: don't use virtio's weak barriers rpmsg: rename virtqueue_add_buf_gfp to virtqueue_add_buf rpmsg: depend on EXPERIMENTAL remoteproc: depend on EXPERIMENTAL rpmsg: add Kconfig menu ... Conflicts: include/linux/virtio_ids.h
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson: "These changes are all specific to one board only. We're trying to keep the number of board files low, but generally board level updates are ok on platforms that are working on moving towards DT based probing, which will eventually lead to removing them. The board-ams-delta.c board file gets a conflict between the removal of ams_delta_config and the addition of a lot of other data. The Kconfig file has two changes in the same line, and in exynos, the power domain cleanup conflicts with the addition of the image sensor device. Signed-off-by: NArnd Bergmann <arnd@arndb.de> [olof: Amended a fix for a mismerge to board-omap4panda.c] Signed-off-by: Olof Johansson <olof@lixom.net>" Fixed up some fairly trivial conflicts manually. * tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits) i.MX35-PDK: Add Camera support ARM : mx35: 3ds-board: add framebuffer device pxa/hx4700: Remove pcmcia platform_device structure ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35% ARM: pxa/hx4700: Remove unwanted request for GPIO105 ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board ARM: EXYNOS: Register JPEG on nuri ARM: EXYNOS: Register JPEG on universal_c210 ARM: S5PV210: Enable JPEG on SMDKV210 ARM: S5PV210: Add JPEG board definition ARM: EXYNOS: Enable JPEG on Origen ARM: EXYNOS: Enable JPEG on SMDKV310 ARM: EXYNOS: Add __init attribute to universal_camera_init() ARM: EXYNOS: Add __init attribute to nuri_camera_init() ARM: S5PV210: Enable FIMC on SMDKC110 ARM: S5PV210: Enable FIMC on SMDKV210 ARM: S5PV210: Enable MFC on SMDKC110 ARM: S5PV210: Enable MFC on SMDKV210 ARM: EXYNOS: Enable G2D on SMDKV310 ARM: tegra: update defconfig ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: SoC specific updates" from Arnd Bergmann: "These changes are all specific to an soc family or the code for one soc. Lots of work for Tegra3 this time, but also a lot of other platforms. There will be another (smaller) set of soc patches later in the merge window for stuff that has dependencies on external trees or that was sent just before the merge window opened. The asoc tree added a few devices to the i.mx platform, which conflict with other devices added in the same place here. The tegra Makefile conflicts between a number of branches, mostly because of changes regarding localtimer.c, which was removed in the end. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" Fix up some trivial conflicts, including the mentioned Tegra Makefile. * tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits) ARM: EXYNOS: fix cycle count for periodic mode of clock event timers ARM: EXYNOS: add support JPEG ARM: EXYNOS: Add DMC1, allow PPMU access for DMC ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata() ARM: SAMSUNG: Add __init attribute to samsung_bl_set() ARM: S5PV210: Add usb otg phy control ARM: S3C64XX: Add usb otg phy control ARM: EXYNOS: Enable l2 configuration through device tree ARM: EXYNOS: remove useless code to save/restore L2 ARM: EXYNOS: save L2 settings during bootup ARM: S5P: add L2 early resume code ARM: EXYNOS: Add support AFTR mode on EXYNOS4210 ARM: mx35: Setup the AIPS registers ARM: mx5: Use common function for configuring AIPS ARM: mx3: Setup AIPS registers ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE ARM: imx: update imx_v6_v7_defconfig ARM: tegra: Demote EMC clock inconsistency BUG to WARN ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: timer cleanup work" from Arnd Bergmann: "These are split out from the generic soc and driver updates because there was a lot of conflicting work by multiple people. Marc Zyngier worked on simplifying the "localtimer" interfaces, and some of the platforms are touching the same code as they move to device tree based booting. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" * tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits) ARM: tegra: select USB_ULPI if USB is selected arm/tegra: pcie: fix return value of function ARM: ux500: fix compilation after local timer rework ARM: shmobile: remove additional __io() macro use ARM: local timers: make the runtime registration interface mandatory ARM: local timers: convert MSM to runtime registration interface ARM: local timers: convert exynos to runtime registration interface ARM: smp_twd: remove old local timer interface ARM: imx6q: convert to twd_local_timer_register() interface ARM: highbank: convert to twd_local_timer_register() interface ARM: ux500: convert to twd_local_timer_register() interface ARM: shmobile: convert to twd_local_timer_register() interface ARM: tegra: convert to twd_local_timer_register() interface ARM: plat-versatile: convert to twd_local_timer_register() interface ARM: OMAP4: convert to twd_local_timer_register() interface ARM: smp_twd: add device tree support ARM: smp_twd: add runtime registration support ARM: local timers: introduce a new registration interface ARM: smp_twd: make local_timer_stop a symbol instead of a #define ARM: mach-shmobile: default to no earlytimer ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: global cleanups" from Arnd Bergmann: "Quite a bit of code gets removed, and some stuff moved around, mostly the old samsung s3c24xx stuff. There should be no functional changes in this series otherwise. Some cleanups have dependencies on other arm-soc branches and will be sent in the second round. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" Fixed up trivial conflicts mainly due to #include's being changes on both sides. * tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits) ep93xx: Remove unnecessary includes of ep93xx-regs.h ep93xx: Move EP93XX_SYSCON defines to SoC private header ep93xx: Move crunch code to mach-ep93xx directory ep93xx: Make syscon access functions private to SoC ep93xx: Configure GPIO ports in core code ep93xx: Move peripheral defines to local SoC header ep93xx: Convert the watchdog driver into a platform device. ep93xx: Use ioremap for backlight driver ep93xx: Move GPIO defines to gpio-ep93xx.h ep93xx: Don't use system controller defines in audio drivers ep93xx: Move PHYS_BASE defines to local SoC header file ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver ARM: EXYNOS: add clock registers for exynos4x12-cpufreq PM / devfreq: update the name of EXYNOS clock registers that were omitted PM / devfreq: update the name of EXYNOS clock register ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock ARM: EXYNOS: use static declaration on regarding clock ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs ARM: OMAP2+: Fix build error after merge ARM: S3C24XX: remove call to s3c24xx_setup_clocks ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: subarch maintainer updates" from Arnd Bergmann: "This is a collection of updates to the MAINTAINERS file, separated out mostly to give an overview of what has changed regarding who does what. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" * tag 'maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: tegra: update main repo and add patchwork MAINTAINERS: update MAINTAINERS email entry MAINTAINERS: update maintainer entry for pxa/hx4700 MAINTAINERS: ARM: tegra: update Stephen's email address MAINTAINERS: add TI DaVinci git tree information MAINTAINERS: mark TI DaVinci list as "moderated" MAINTAINERS: remove arch/arm/mach-mx*/ from IMX entry
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull "ARM: Non-critical bug fixes" from Ardn Bergmann: "Simple bug fixes that were not considered important enough for inclusion into 3.3. One bug fix was originally intended for 3.3 but accidentally got missed, but is not marked stable because it should only get backported once later fixes also make it into v3.4. Signed-off-by: Arnd Bergmann <arnd@arndb.de>" * tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (66 commits) iomux-mx25.h slew rate adjusted for LCD __LD pins ARM: davinci: DA850: move da850_register_pm to .init.text ARM: davinci: cpufreq: fix compiler warning ARM: OMAP2+: Fix build for omap4 only builds with missing include of linux/bug.h ARM: OMAP2+: Fix section warnings for hsmmc_init_one ARM: OMAP2+: Fix build issues with missing include of linux/bug.h ARM: OMAP2+: gpmc-smsc911x: only register regulator for first instance ARM: OMAP3+: PM: VP: fix integer truncation error ARM: OMAP2+: PM: fix wakeupgen warning when hotplug disabled ARM: OMAP2+: PM: fix section mismatch with omap2_init_processor_devices() ARM: OMAP2: Fix section warning for n8x0 when CONFIG_MMC_OMAP is not set ARM: OMAP2+: Fix omap24xx_io_desc warning if SoC subtypes are not selected ARM: OMAP1: Fix section mismatch for omap1_init_early() ARM: OMAP1: Fix typo in lcd_dma.c ARM: OMAP: mailbox: trivial whitespace fix ARM: OMAP: Remove definition cpu_is_omap4430() ARM: OMAP2+: included some headers twice ARM: OMAP: clock.c: included linux/debugfs.h twice ARM: OMAP: don't build hwspinlock in vain ARM: OMAP2+: ads7846_init: put gpio_pendown into pdata if it's provided ...
-
由 Eric Dumazet 提交于
Commit f2c31e32 (net: fix NULL dereferences in check_peer_redir() ) added a regression in rt6_fill_node(), leading to rcu_read_lock() imbalance. Thats because NLA_PUT() can make a jump to nla_put_failure label. Fix this by using nla_put() Many thanks to Ben Greear for his help Reported-by: NBen Greear <greearb@candelatech.com> Reported-by: NDave Jones <davej@redhat.com> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Tested-by: NBen Greear <greearb@candelatech.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnd Bergmann 提交于
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into next/boards The asoc branch that was already merged into v3.4 contains some board-level changes that conflict with patches we already have here, so pull in that branch to resolve the conflicts. Conflicts: arch/arm/mach-imx/mach-imx27_visstrim_m10.c arch/arm/mach-omap2/board-omap4panda.c Signed-off-by: NArnd Bergmann <arnd@arndb.de> [olof: Amended fix for mismerge as reported by Kevin Hilman] Signed-off-by: NOlof Johansson <olof@lixom.net>
- 27 3月, 2012 12 次提交
-
-
由 Larry Finger 提交于
In https://bugzilla.redhat.com/show_bug.cgi?id=770207, slowdowns of driver rtl8192ce are reported. One fix (commit a9b89e25) has already been applied, and it helped, but the maximum RX speed would still drop to 1 Mbps. As in the previous fix, the initial gain was determined to be the problem; however, the problem arises from a setting of the gain when scans are started. Driver rtl8192de also has the same code structure - this one is fixed as well. Reported-and-Tested-by: NIvan Pesin <ivan.pesin@gmail.com> Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
I simply don't have any hobby hacking time after family time and non-kernel-related job time, so I resume status as part-time mailing list lurker. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Is possible that we will arm the tid_rx->reorder_timer after del_timer_sync() in ___ieee80211_stop_rx_ba_session(). We need to stop timer after RCU grace period finish, so move it to ieee80211_free_tid_rx(). Timer will not be armed again, as rcu_dereference(sta->ampdu_mlme.tid_rx[tid]) will return NULL. Debug object detected problem with the following warning: ODEBUG: free active (active state 0) object type: timer_list hint: sta_rx_agg_reorder_timer_expired+0x0/0xf0 [mac80211] Bug report (with all warning messages): https://bugzilla.redhat.com/show_bug.cgi?id=804007Reported-by: N"jan p. springer" <jsd@igroup.org> Cc: stable@vger.kernel.org Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Another good catch from Jakub Kicinski. This patch fixes my recent commit: ed61e2b0 "rt2x00: rt2800usb: rework txdone code" We should reread status register only when nobody else start already reading status i.e. test_and_set_bit(TX_STATUS_READING, flags) return 0. Reported-by: NJakub Kicinski <moorray@wp.pl> Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NGertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
This is fix for my current commit ed61e2b0 "rt2x00: rt2800usb: rework txdone code" We should schedule txdone work on timeout, otherwise if newer get tx status from hardware, we will never report tx status to mac80211 and eventually never wakeup tx queue. Reported-by: NJakub Kicinski <moorray@wp.pl> Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NGertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eliad Peller 提交于
The on-oper-channel optimization was reverted, so remove the outdated comment as well. Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eric Dumazet 提交于
commit 0d95521e (ath9k: use split rx buffers to get rid of order-1 skb allocations) added in memory leak in error path. sc->rx.frag should be cleared after the pskb_expand_head() call, or else we jump to requeue_drop_frag and leak an skb. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Felix Fietkau <nbd@openwrt.org> Cc: John W. Linville <linville@tuxdriver.com> Cc: Trond Wuellner <trond@chromium.org> Cc: Grant Grundler <grundler@chromium.org> Cc: Paul Stewart <pstew@chromium.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
When we have downlink traffic alone and the station is going thru bgscan, the client is out of operating channel for around 1000ms which is too long. The mac80211 decides when to switch back to oper channel based on tx queue, bad latency and listen time. As the station does not have tx traffic, the bgscan can easily affect downlink throughput. By reducing the listen time, it helps the associated AP to retain the downstream rate. Cc: Paul Stewart <pstew@google.com> Tested-by: NGary Morain <gmorain@google.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
The station_info struct had demanded dBm signal values, but the cfg80211 wireless extensions implementation was also accepting "unspecified" (i.e. RSSI) unit values while the nl80211 code was completely unaware of them. Resolve this by formally allowing the "unspecified" units while making nl80211 ignore them. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Stanislaw Gruszka 提交于
Current commit 0775f9f9 "mac80211: remove spurious BSSID change flag" exposed bug on iwlegacy, that we do not set BSSID address correctly and then device was not able to receive frames after successful associate. On the way fix scan canceling comment. Apparently ->post_associate() do cancel scan itself, but scan cancel on BSS_CHANGED_BSSID is needed. I'm not sure why, but when I removed it, I had frequent auth failures: wlan4: send auth to 54:e6:fc:98:63:fe (try 1/3) wlan4: send auth to 54:e6:fc:98:63:fe (try 2/3) wlan4: send auth to 54:e6:fc:98:63:fe (try 3/3) wlan4: authentication with 54:e6:fc:98:63:fe timed out Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Currently the maximum noise floor limit is set as too high (-60dB). The assumption of having a higher threshold limit is that it would help de-sensitize the receiver (reduce phy errors) from continuous interference. But when we have a bursty interference where there are collisions and then free air time and if the receiver is desensitized too much, it will miss the normal packets too. Lets make use of chips specific min, nom and max limits always. This patch helps to improve the connection stability in congested networks. Cc: stable@vger.kernel.org Cc: Paul Stewart <pstew@google.com> Tested-by: NGary Morain <gmorain@google.com> Signed-off-by: NMadhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
This il->vif is dereferenced in different part of iwlegacy code, so do not nullify it. This should fix random crashes observed in companion with microcode errors i.e. crash in il3945_config_ap(). Additionally this should address also WARNING: at drivers/net/wireless/iwlegacy/common.c:4656 il_mac_remove_interface at least one of the possible reasons of that warning. Cc: stable@vger.kernel.org Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 26 3月, 2012 5 次提交
-
-
由 Eric Dumazet 提交于
skb_add_rx_frag() API is misleading. Network skbs built with this helper can use uncharged kernel memory and eventually stress/crash machine in OOM. Add a 'truesize' parameter and then fix drivers in followup patches. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Space allocated for int_name_<foo> is insufficient for maximal device name, expand it. Code to create int_name_<foo> is obscure, simplify it by using sprintf. Found by looking for unnecessary \ line continuations. Signed-off-by: NJoe Perches <joe@perches.com> Tested-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
Now that we have the beginnings of an OSS method to use the network interfaces on these USB broadband modems, add the ZTE manufactured Vodafone items to the whitelist Signed-off-by: NAndrew Bird <ajb@spheresystems.co.uk> Acked-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
These interfaces need to be handled by QMI/WWAN driver Signed-off-by: NAndrew Bird <ajb@spheresystems.co.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
Now that we have the beginnings of an OSS method to use the network interfaces on these USB broadband modems, add the ZTE manufactured Vodafone items to the whitelist Signed-off-by: NAndrew Bird <ajb@spheresystems.co.uk> Acked-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 3月, 2012 5 次提交
-
-
由 Linus Torvalds 提交于
Merge tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull more xen updates from Konrad Rzeszutek Wilk: "One tiny feature that accidentally got lost in the initial git pull: * Add fast-EOI acking of interrupts (clear a bit instead of hypercall) And bug-fixes: * Fix CPU bring-up code missing a call to notify other subsystems. * Fix reading /sys/hypervisor even if PVonHVM drivers are not loaded. * In Xen ACPI processor driver: remove too verbose WARN messages, fix up the Kconfig dependency to be a module by default, and add dependency on CPU_FREQ. * Disable CPU frequency drivers from loading when booting under Xen (as we want the Xen ACPI processor to be used instead). * Cleanups in tmem code." * tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/acpi: Fix Kconfig dependency on CPU_FREQ xen: initialize platform-pci even if xen_emul_unplug=never xen/smp: Fix bringup bug in AP code. xen/acpi: Remove the WARN's as they just create noise. xen/tmem: cleanup xen: support pirq_eoi_map xen/acpi-processor: Do not depend on CPU frequency scaling drivers. xen/cpufreq: Disable the cpu frequency scaling drivers from loading. provide disable_cpufreq() function to disable the API.
-
由 Rik van Riel 提交于
We should only test compaction_suitable if the kernel is built with CONFIG_COMPACTION, otherwise the stub compaction_suitable function will always return COMPACT_SKIPPED and send kswapd into an infinite loop. Reported-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NRik van Riel <riel@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux由 Linus Torvalds 提交于
Pull <linux/device.h> avoidance patches from Paul Gortmaker: "Nearly every subsystem has some kind of header with a proto like: void foo(struct device *dev); and yet there is no reason for most of these guys to care about the sub fields within the device struct. This allows us to significantly reduce the scope of headers including headers. For this instance, a reduction of about 40% is achieved by replacing the include with the simple fact that the device is some kind of a struct. Unlike the much larger module.h cleanup, this one is simply two commits. One to fix the implicit <linux/device.h> users, and then one to delete the device.h includes from the linux/include/ dir wherever possible." * tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: device.h: audit and cleanup users in main include dir device.h: cleanup users outside of linux/include (C files)
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux由 Linus Torvalds 提交于
Pull cleanup of fs/ and lib/ users of module.h from Paul Gortmaker: "Fix up files in fs/ and lib/ dirs to only use module.h if they really need it. These are trivial in scope vs the work done previously. We now have things where any few remaining cleanups can be farmed out to arch or subsystem maintainers, and I have done so when possible. What is remaining here represents the bits that don't clearly lie within a single arch/subsystem boundary, like the fs dir and the lib dir. Some duplicate includes arising from overlapping fixes from independent subsystem maintainer submissions are also quashed." Fix up trivial conflicts due to clashes with other include file cleanups (including some due to the previous bug.h cleanup pull). * tag 'module-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: lib: reduce the use of module.h wherever possible fs: reduce the use of module.h wherever possible includecheck: delete any duplicate instances of module.h
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux由 Linus Torvalds 提交于
Pull <linux/bug.h> cleanup from Paul Gortmaker: "The changes shown here are to unify linux's BUG support under the one <linux/bug.h> file. Due to historical reasons, we have some BUG code in bug.h and some in kernel.h -- i.e. the support for BUILD_BUG in linux/kernel.h predates the addition of linux/bug.h, but old code in kernel.h wasn't moved to bug.h at that time. As a band-aid, kernel.h was including <asm/bug.h> to pseudo link them. This has caused confusion[1] and general yuck/WTF[2] reactions. Here is an example that violates the principle of least surprise: CC lib/string.o lib/string.c: In function 'strlcat': lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON' make[2]: *** [lib/string.o] Error 1 $ $ grep linux/bug.h lib/string.c #include <linux/bug.h> $ We've included <linux/bug.h> for the BUG infrastructure and yet we still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.] Ugh - very confusing for someone who is new to kernel development. With the above in mind, the goals of this changeset are: 1) find and fix any include/*.h files that were relying on the implicit presence of BUG code. 2) find and fix any C files that were consuming kernel.h and hence relying on implicitly getting some/all BUG code. 3) Move the BUG related code living in kernel.h to <linux/bug.h> 4) remove the asm/bug.h from kernel.h to finally break the chain. During development, the order was more like 3-4, build-test, 1-2. But to ensure that git history for bisect doesn't get needless build failures introduced, the commits have been reorderd to fix the problem areas in advance. [1] https://lkml.org/lkml/2012/1/3/90 [2] https://lkml.org/lkml/2012/1/17/414" Fix up conflicts (new radeon file, reiserfs header cleanups) as per Paul and linux-next. * tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: kernel.h: doesn't explicitly use bug.h, so don't include it. bug: consolidate BUILD_BUG_ON with other bug code BUG: headers with BUG/BUG_ON etc. need linux/bug.h bug.h: add include of it to various implicit C users lib: fix implicit users of kernel.h for TAINT_WARN spinlock: macroize assert_spin_locked to avoid bug.h dependency x86: relocate get/set debugreg fcns to include/asm/debugreg.
-