On systems with mismatched i/d cache min line sizes, we need to use
the smallest size possible across all CPUs. This will be done by fetching
the system wide safe value from CPU feature infrastructure.
However the some special users(e.g kexec, hibernate) would need the line
size on the CPU (rather than the system wide), when either the system
wide feature may not be accessible or it is guranteed that the caller
executes with a gurantee of no migration.
Provide another helper which will fetch cache line size on the current CPU.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

adrp uses PC-relative address offset to a page (of 4K size) of
a symbol. If it appears in an alternative code patched in, we
should adjust the offset to reflect the address where it will
be run from. This patch adds support for fixing the offset
for adrp instructions.

Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Adds helpers for decoding/encoding the PC relative addresses for adrp.
This will be used for handling dynamic patching of 'adrp' instructions
in alternative code patching.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The alternative code patching doesn't check if the replaced instruction
uses a pc relative literal. This could cause silent corruption in the
instruction stream as the instruction will be executed from a different
address than what it was compiled for. Catch all such cases.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Suggested-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Right now we run through the work around checks on a CPU
from __cpuinfo_store_cpu. There are some problems with that:

1) We initialise the system wide CPU feature registers only after the
Boot CPU updates its cpuinfo. Now, if a work around depends on the
variance of a CPU ID feature (e.g, check for Cache Line size mismatch),
we have no way of performing it cleanly for the boot CPU.

2) It is out of place, invoked from __cpuinfo_store_cpu() in cpuinfo.c. It
is not an obvious place for that.

This patch rearranges the CPU specific capability(aka work around) checks.

1) At the moment we use verify_local_cpu_capabilities() to check if a new
CPU has all the system advertised features. Use this for the secondary CPUs
to perform the work around check. For that we rename
  verify_local_cpu_capabilities() => check_local_cpu_capabilities()
which:

   If the system wide capabilities haven't been initialised (i.e, the CPU
   is activated at the boot), update the system wide detected work arounds.

   Otherwise (i.e a CPU hotplugged in later) verify that this CPU conforms to the
   system wide capabilities.

2) Boot CPU updates the work arounds from smp_prepare_boot_cpu() after we have
initialised the system wide CPU feature values.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This is a cosmetic change to rename the functions dealing with
the errata work arounds to be more consistent with their naming.

1) check_local_cpu_errata() => update_cpu_errata_workarounds()
check_local_cpu_errata() actually updates the system's errata work
arounds. So rename it to reflect the same.

2) verify_local_cpu_errata() => verify_local_cpu_errata_workarounds()
Use errata_workarounds instead of _errata.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Right now we use 0 as the safe value for CTR_EL0:L1Ip, which is
not defined at the moment. The safer value for the L1Ip should be
the weakest of the policies, which happens to be AIVIVT. While at it,
fix the comment about safe_val.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

1. Remove the old binding code.
2. Read the nid of cpu0 from dts.
3. Fallback the nid of cpu0 to 0 when numa=off is set in bootargs.
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

When the deleted code is executed, only the bit of cpu0 was set on
cpu_possible_mask. So that, only set_cpu_numa_node(0, NUMA_NO_NODE); will
be executed. And map_cpu_to_node(0, 0) will soon be called. So these code
can be safely removed.
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

To make each percpu area allocated from its local numa node. Without this
patch, all percpu areas will be allocated from the node which cpu0 belongs
to.
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Use pr_fmt to prefix kernel output, and remove duplicated msg
of NUMA turned off.
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Use pr_fmt to prefix kernel output.
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Use of_get_next_parent() instead of open-code.
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

numa_init may return error because of numa configuration error. So "No
NUMA configuration found" is inaccurate. In fact, specific configuration
error information should be immediately printed by the testing branch.
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This warning has been printed in of_numa_parse_cpu_nodes before.
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

If the numa-id which was configured in memory@ devicetree node is greater
than MAX_NUMNODES, we should report a warning. We have done this for cpus
and distance-map dt nodes, this patch help them to be consistent.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

For a normal memory@ devicetree node, its reg property can contains more
memory blocks.

Because we don't known how many memory blocks maybe contained, so we try
from index=0, increase 1 until error returned(the end).
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This information will be printed in the subfunction numa_add_memblk.
They are not the same, but very similar.
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

In systems with heterogeneous CPUs, there are multiple logical CPU PMUs,
each of which covers a subset of CPUs in the system. In some cases
userspace needs to know which CPUs a given logical PMU covers, so we'd
like to expose a cpumask under sysfs, similar to what is done for uncore
PMUs.

Unfortunately, prior to commit 00e727bb ("perf stat: Balance
opening and reading events"), perf stat only correctly handled a cpumask
holding a single CPU, and only when profiling in system-wide mode. In
other cases, the presence of a cpumask file could cause perf stat to
behave erratically.

Thus, exposing a cpumask file would break older perf binaries in cases
where they would otherwise work.

To avoid this issue while still providing userspace with the information
it needs, this patch exposes a differently-named file (cpus) under
sysfs. New tools can look for this and operate correctly, while older
tools will not be adversely affected by its presence.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Now that the 32-bit and 64-bit perf backends use the common groups
directly, remove the fallback and no longer allow the groups array to be
overridden.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

By using a common attr_groups array, the common arm_pmu code can set up
common files (e.g. cpumask) for us in subsequent patches.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

By using a common attr_groups array, the common arm_pmu code can set up
common files (e.g. cpumask) for us in subsequent patches.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

In preparation for adding common attribute groups, add an array of
attribute group pointers to arm_pmu, which will be used if the
backend hasn't already set pmu::attr_groups.

Subsequent patches will move backends over to using these, before adding
common fields.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

When CONFIG_PID_IN_CONTEXTIDR is not selected, we use an empty stub
definition of contextidr_thread_switch(). As everything we rely upon
exists regardless of CONFIG_PID_IN_CONTEXTIDR, we don't strictly require
an empty stub.

By using IS_ENABLED() rather than ifdeffery, we avoid duplication, and
get compiler coverage on all the code even when CONFIG_PID_IN_CONTEXTIDR
is not selected and the code is optimised away.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.

This patch makes use of these across arm64 to make code shorter and
clearer. For sequences with a trailing ISB, the existing isb() macro is
also used so that asm blocks can be removed entirely.

A few uses of inline assembly for msr/mrs are left as-is. Those
manipulating sp_el0 for the current thread_info value have special
clobber requiremends.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.

This patch makes use of these in the arm64 KVM code to make the code
shorter and clearer.

At the same time, a comment style violation next to a system register
access is fixed up in reset_pmcr, and comments describing whether
operations are reads or writes are removed as this is now painfully
obvious.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.

This patch makes use of these in the arm64 DCC accessors to make the
code shorter and clearer.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.

This patch makes use of these in the arm64 arch timer accessors to make
the code shorter and clearer.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Currently write_sysreg has to allocate a temporary register to write
zero to a system register, which is unfortunate given that the MSR
instruction accepts XZR as an operand.

Allow XZR to be used when appropriate by fiddling with the assembly
constraints.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

When zeroing an I/O location, the current accessors are forced to
allocate a temporary register to store the zero for the write. By
tweaking the assembly constraints, we can allow the compiler to use
the zero register directly in such cases, and save some juggling.
Compiling a representative kernel configuration with GCC 6 shows
that 2.3KB worth of code can be wasted just on that!

  text     data    bss      dec      hex     filename
 13316776 3248256 18176769 34741801 2121e29 vmlinux.o.new
 13319140 3248256 18176769 34744165 2122765 vmlinux.o.old
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This patch adds static keys transparently for all the cpu_hwcaps
features by implementing an array of default-false static keys and
enabling them when detected. The cpus_have_cap() check uses the static
keys if the feature being checked is a constant, otherwise the compiler
generates the bitmap test.

Because of the early call to static_branch_enable() via
check_local_cpu_errata() -> update_cpu_capabilities(), the jump labels
are initialised in cpuinfo_store_boot_cpu().

Cc: Will Deacon <will.deacon@arm.com>
Cc: Suzuki K. Poulose <Suzuki.Poulose@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The static key API is currently designed around single variable
definitions. There are cases where an array of static keys is desirable,
so extend the API to allow this rather than using the internal static
key implementation directly.

Cc: Jason Baron <jbaron@akamai.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Suggested-by: NDave P Martin <Dave.Martin@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

There is only fixup_init() in mm.h , and it is only called
in free_initmem(), so move the codes from fixup_init() into
free_initmem(), then drop fixup_init() and mm.h.
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

As declared by the chief penguin, and enforced by the NO_IRQ brigade,
IRQ0 doesn't exist, and is considered as an error (no irq).

Unfortunately, the arm_pmu driver still considers it as valid in
a large number of cases. Let's fix this.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Currently, enabling stacktrace of a kprobe events generates warning:

  echo stacktrace > /sys/kernel/debug/tracing/trace_options
  echo "p xhci_irq" > /sys/kernel/debug/tracing/kprobe_events
  echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable

save_stack_trace_regs() not implemented yet.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at ../kernel/stacktrace.c:74 save_stack_trace_regs+0x3c/0x48
Modules linked in:

CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc4-dirty #5128
Hardware name: ARM Juno development board (r1) (DT)
task: ffff800975dd1900 task.stack: ffff800975ddc000
PC is at save_stack_trace_regs+0x3c/0x48
LR is at save_stack_trace_regs+0x3c/0x48
pc : [<ffff000008126c64>] lr : [<ffff000008126c64>] pstate: 600003c5
sp : ffff80097ef52c00

Call trace:
   save_stack_trace_regs+0x3c/0x48
   __ftrace_trace_stack+0x168/0x208
   trace_buffer_unlock_commit_regs+0x5c/0x7c
   kprobe_trace_func+0x308/0x3d8
   kprobe_dispatcher+0x58/0x60
   kprobe_breakpoint_handler+0xbc/0x18c
   brk_handler+0x50/0x90
   do_debug_exception+0x50/0xbc

This patch implements save_stack_trace_regs(), so that stacktrace of a
kprobe events can be obtained.

After this patch, there is no warning and we can see the stacktrace for
kprobe events in trace buffer.

more /sys/kernel/debug/tracing/trace
          <idle>-0     [004] d.h.  1356.000496: p_xhci_irq_0:(xhci_irq+0x0/0x9ac)
          <idle>-0     [004] d.h.  1356.000497: <stack trace>
  => xhci_irq
  => __handle_irq_event_percpu
  => handle_irq_event_percpu
  => handle_irq_event
  => handle_fasteoi_irq
  => generic_handle_irq
  => __handle_domain_irq
  => gic_handle_irq
  => el1_irq
  => arch_cpu_idle
  => default_idle_call
  => cpu_startup_entry
  => secondary_start_kernel
  =>
Tested-by: NDavid A. Long <dave.long@linaro.org>
Reviewed-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NPratyush Anand <panand@redhat.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Commit b5fe2429 ("arm64: kernel: fix style issues in sleep.S")
changed the linkage of _cpu_resume() to local, even though the symbol
is also referenced from hibernate.c. So revert this change.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The code that provides /dev/mem uses xlate_dev_mem_{k,}ptr() to
avoid making a cachable mapping of a non-cachable area on ia64.
On arm64 we do this via phys_mem_access_prot() instead, but provide
dummy versions of xlate_dev_mem_{k,}ptr().

These are the same as those in asm-generic/io.h, which we include from
asm/io.h
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Single-step traps to userspace (e.g. via ptrace) are expected to use
the TRAP_TRACE for the si_code field of the siginfo, as opposed to
TRAP_HWBRPT that we report currently.

Fix the reported value, which has no effect on existing and legacy
builds of GDB.
Reported-by: NYao Qi <yao.qi@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Now that the only remaining occurrences of the use of callee saved
registers are on the primary boot path, add a comment to the code
which register is used for what.
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Instead of stashing the value of the link register in x28 before setting
up the stack and calling into C code, create an ordinary PCS compatible
stack frame so that we can push the return address onto the stack.

Since exception handlers require a stack as well, assign the stack pointer
register before installing the vector table.

Note that this accounts for the difference between THREAD_START_SP and
THREAD_SIZE, given that the stack pointer is always decremented before
calling into any C code.
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>