Change the datatype of "ip_addr" to __be32 as 'ip' should be in
big endian format.

Adapter needs "ip address" in big endian format stored at lower 32bit
of req.word[1]. netxen_config_ipaddr() now receives 'ip' in big endian
format. To satisfy adapter's need, use memcpy() to copy byte by byte
of 'ip' into lower 32bit of req.word[1].

Mac address and serial number of adapter need to be in little endian format.
Change the data type of the related  variables to __le32 / __le64 or cast it
explicitly to __le32 / __le64 depending upon the requirement.
Signed-off-by: NSantosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch removes unused stats member in pxa168 network driver.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/ath/ath9k/hw.c

Changes:
- removed a limit for amount of datagrams for IN NTB
- using pointer to traverse NTB in rx_fixup()
- renamed "temp" to "len" in rx_fixup()
- do NTB sequence number check in rx path
Tested on Intel/ARM.
Reviewed-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NDmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes/fixes:
- inform device if max_datagram_size was changed by host
- max_datagram_size can't be bigger MTU in ETH func descr
- fix constants definitions to enable running CAIF service over NCM

Tested on Intel/ARM.
Reviewed-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NDmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes:
- use high resolution timer
  latency became approx. 10-15 times less than before
- use taklet for sending remaining data in tx path
Tested on Intel/ARM.
Reviewed-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NDmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

asix_rx_fixup() is complex, and does some unnecessary memory copies (at
least on x86 where NET_IP_ALIGN is 0)

Also, it tends to provide skbs with a big truesize (4096+256 with
MTU=1500) to upper stack, so incoming trafic consume a lot of memory and
I noticed early packet drops because we hit socket rcvbuf too fast.

Switch to a different strategy, using copybreak so that we provide nice
skbs to upper stack (including the NET_SKB_PAD to avoid future head
reallocations in some paths)

With this patch, I no longer see packets drops or tcp collapses on
various tcp workload with a AX88772 adapter.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Aurelien Jacobs <aurel@gnuage.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Reviewed-by: NGrant Grundler <grundler@chromium.org>
Reviewed-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

libertas provides a dump_survey implementation based on reading of
a RSSI value. However, this RSSI value is calculated based on the
last received beacon from the associated AP - it is not a good
way of surveying a channel in general, and even causes an error
if the card is not associated to a network.

As this is not appropriate as a survey, remove it. This fixes an
issue where something in userspace is repeatedly calling site-survey
during boot, resulting in many repeated errors as the RSSI value cannot
be read before associating.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Makes them more readable and reduces code size
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program tx gain through iniModesTxGain like on AR9287
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

use iniModesFastClock for 5 ghz fast clock specific settings, and
iniAdditional for clock/chip specific initval overrides
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program the ah->ini_japan2484 INI values which were left out by accident
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These arrays are unused
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be
cleared on all non-EDMA PCI/AHB based chipsets anyway.
Limit the memset to the rx status area to improve performance.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver can just check the mask directly
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and
used together, and they share the same bitmask in enum ath9k_tx_queue_flags.
Simplify the code that tests for these flags.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

uapsd_queues and uapsd_max_sp_len are relevant only for managed
interfaces, and can be configured differently for each vif.

Move them from the local struct to sdata->u.mgd, and update
the debugfs functions accordingly.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some debugfs write functions call kstrto* functions, which
assume the string is null-terminated. Make it valid by changing
ieee80211_if_write() to use static buffer instead of allocating
one, and set the last char to NULL.

(The write functions try to parse some integer/mac address,
so 64 bytes buffer should be enough)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current max throughput rate is known to be good as otherwise it
wouldn't be the max throughput rate. Since rate sampling can introduce
some overhead (by adding RTS for example or due to not aggregating the
frame) don't sample the max throughput rate.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX status fifo is limited to 16 elements. When we send more frames than
that, we can easily loose status, what is not good for rate scaling
algorithm.

On my testing the change does not degrade performance, actually make
is slightly better. Additionally with the patch I can see much less
various rt2x00 warnings in dmesg.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx statuses of aggregated subframes contain packetid of first subframe
in the AMPDU. We can not identify AMPDU subframes based on packedid, so
simply assume that status match first pending frame in the queue. Thats
mostly the same what 2800pci do.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently we read tx status register after each urb data transfer. As
callback procedure also trigger reading, that causing we have many
"threads" of reading status. To prevent that introduce TX_STATUS_READING
flags, and check if we are already in process of sequential reading
TX_STA_FIFO, before requesting new reads.

Change timer to hrtimer, that make TX_STA_FIFO overruns less possible.
Use 200 us for initial timeout, and then reschedule in 100 us period,
this values probably have to be tuned.

Make changes on txdone work. Schedule it from
rt2800usb_tx_sta_fifo_read_completed() callback when first valid status
show up. Check in callback if tx status timeout happens, and schedule
work on that condition too. That make possible to remove tx status
timeout from generic watchdog. I moved that to rt2800usb.

Loop in txdone work, that should prevent situation when we queue work,
which is already processed, and after finish work is not rescheduled
again.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch change txdone code to make it similar like txdone in rt2800pci,
process only one entry from queue matching tx status.

Before we processed all pending entries from queue until PACKEDID match,
that caused that we do not report tx statuses correctly.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 provides short preamble information and ERP protection
information on a per-BSS basis, which can be used. Remove flags
stored in the driver, which was incorrect since they were being used
in a global manner.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed.
The HT capabilities of the station and HW can be used instead.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The logic to determine whether to use FCC is a bit convoluted.
Use a small helper function to decide whether FCC is to be
used.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not needed and will not be used anyway since
unsupported interfaces are not allowed to be created.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to mask out SWBA/BMISS from the
interrupt mask in start().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800 already reports the tx ack status of each frame back to mac80211.
Advertise this by setting IEEE80211_HW_REPORTS_TX_ACK_STATUS for rt2800.
This allows some mac80211 features like frame loss notifications to work
with rt2800.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"hscfg" is declared as struct mwifiex_ds_hs_cfg. Use same structure
name for calculating it's size.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For files sta_rx.c, sta_tx.c, txrx.c, util.c and wmm.c
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>