Add or remove a Virtual Function after receiving a Migrate In or Out
Request.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add or remove the Virtual Function when the SR-IOV is enabled or
disabled by the device driver. This can happen anytime rather than
only at the device probe stage.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If a device has the SR-IOV capability, initialize it (set the ARI
Capable Hierarchy in the lowest numbered PF if necessary; calculate
the System Page Size for the VF MMIO, probe the VF Offset, Stride
and BARs). A lock for the VF bus allocation is also initialized if
a PF is the lowest numbered PF.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

On the Compaq Evo D510 SFF/CMT, a PCI quirk activated the SMBus device
based on detection of the on-board VGA controller, but the on-board
VGA is disabled if an AGP card is inserted, so look for one of the USB
controllers instead.
Signed-off-by: NDavid O'Shea <dcoshea@hotmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add the new API pci_enable_msi_block() to allow drivers to
request multiple MSI and reimplement pci_enable_msi in terms of
pci_enable_msi_block.  Ensure that the architecture back ends don't
have to know about multiple MSI.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Since most of the callers already know whether they have an MSI or
an MSI-X capability, split msi_set_mask_bits() into msi_mask_irq()
and msix_mask_irq().  The only callers which don't (mask_msi_irq()
and unmask_msi_irq()) can share code in msi_set_mask_bit().  This then
becomes the only caller of msix_flush_writes(), so we can inline it.
The flushing read can be to any address that belongs to the device,
so we can eliminate the calculation too.

We can also get rid of maskbits_mask from struct msi_desc and simply
recalculate it on the rare occasion that we need it.  The single-bit
'masked' element is replaced by a copy of the 32-bit 'masked' register,
so this patch does not affect the size of msi_desc.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

MSI interrupts have a mask_pos where MSI-X have a mask_base.  Use a
transparent union to get rid of some ugly casts.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

By changing from a 5-bit field to a 1-bit field, we free up some bits
that can be used by a later patch.  Also rearrange the fields for better
packing on 64-bit platforms (reducing the size of msi_desc from 72 bytes
to 64 bytes).
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Reviewed-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Current acpi_find_root_bridge_handle() has a assumption that
pci_bus->self is NULL on the root pci bus. But it might not be true on
some platforms. Because of this wrong assumption, current
acpi_find_root_bridge_handle() might cause endless loop. We must check
pci_bus->parent instead.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Current acpi_pci_get_bridge_handle() has an assumption that
pci_bus->self is NULL on the root pci bus. But it might not true on
some platforms. Because of this wrong assumption, current
acpi_pci_get_bridge_handle() might return improper ACPI handle. We
must check pci_bus->parent instead.

This bug is the root cause of the following kernel panic reported by
James Bottomley. This problem was introduced by the commit
e8c331e9. The immediate cause was
acpi_pci_get_bridge_handle() returned NULL unexpectedly and it was
passed as the second argument of acpi_walk_namespace().

pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffff8039646f>] acpi_ns_get_next_node+0xb/0x3c
PGD 0
Oops: 0000 [#1] SMP
last sysfs file:
CPU 0
Modules linked in:
Pid: 1, comm: swapper Not tainted 2.6.28 #1
RIP: 0010:[<ffffffff8039646f>]  [<ffffffff8039646f>] acpi_ns_get_next_node+0xb/0x3c
RSP: 0018:ffff88007f87fd30  EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffffffff8037d260 R09: ffff88007f87fdfc
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffffffff80742040(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000010 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff88007f87e000, task ffff88007f875040)
Stack:
 0000000000000000 ffffffff803964f5 ffff88007f81b728 0000000000001001
 ffff88007f87fdfc ffffffff8037d260 0000000600000001 0000000000000000
 ffffffff8037d260 0000000000000000 0000000000000001 ffff88007f87fdfc
Call Trace:
 [<ffffffff803964f5>] acpi_ns_walk_namespace+0x55/0x138
 [<ffffffff8037d260>] is_pci_dock_device+0x0/0x20
 [<ffffffff8037d260>] is_pci_dock_device+0x0/0x20
 [<ffffffff80394a9e>] acpi_walk_namespace+0x5f/0x83
 [<ffffffff8037dd33>] detect_ejectable_slots+0x53/0x70
 [<ffffffff8037de38>] add_bridge+0xe8/0x200
 [<ffffffff80394aaa>] acpi_walk_namespace+0x6b/0x83
 [<ffffffff803a4ad1>] acpi_pci_register_driver+0x48/0x61
 [<ffffffff806fc5df>] acpiphp_init+0x0/0x58
 [<ffffffff806fc732>] acpiphp_glue_init+0x4c/0x5a
 [<ffffffff806fc616>] acpiphp_init+0x37/0x58
 [<ffffffff8020903b>] _stext+0x3b/0x180
 [<ffffffff80312598>] create_proc_entry+0x58/0xa0
 [<ffffffff802815d1>] register_irq_proc+0xc1/0xe0
 [<ffffffff806db64b>] kernel_init+0x152/0x1ac
 [<ffffffff8023d970>] finish_task_switch+0x0/0x110
 [<ffffffff8020ca7a>] child_rip+0xa/0x20
 [<ffffffff8020c47c>] restore_args+0x0/0x30
 [<ffffffff806db4f9>] kernel_init+0x0/0x1ac
 [<ffffffff8020ca70>] child_rip+0x0/0x20
Code: 89 c2 48 8b 00 48 85 c0 75 f5 48 8b 45 00 48 89 02 44 88 65 09 48 89 5d 00 31 c0 5b 5d 41 5c c3 53 48 85 d2 89 fb 48 89 d7 75 06 <48> 8b 56 10 eb 08 e8 73 f1 ff ff 48 89 c2 85 db 74 1a eb 13 0f
RIP  [<ffffffff8039646f>] acpi_ns_get_next_node+0xb/0x3c
 RSP <ffff88007f87fd30>
CR2: 0000000000000010
---[ end trace a7919e7f17c0a725 ]---
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Implement pm object for the PCI Express port driver in order to use
the new power management framework and reduce the code size.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

drivers/pci/hotplug/fakephp.c: In function 'pci_rescan_bus':
drivers/pci/hotplug/fakephp.c:271: warning: passing argument 1 of 'pci_bus_assign_resources' discards qualifiers from pointer target type
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

drivers/pci/hotplug/fakephp.c:283: warning: passing argument 1 of 'pci_bus_add_devices' discards qualifiers from pointer target type
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

- Rename pci_osc_control_set() to acpi_pci_osc_control_set() according
  to the other API names in drivers/acpi/pci_root.c.

- Move _OSC related definitions to include/linux/acpi.h because _OSC
  related API is implemented in drivers/acpi/pci_root.c now.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Tested-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Move PCI _OSC management code from drivers/pci/pci-acpi.c to
drivers/acpi/pci_root.c. The benefits are

- We no longer need struct osc_data and its management code (contents
  are moved to struct acpi_pci_root). This simplify the code, and we
  no longer care about kmalloc() failure.

- We can make pci_acpi_osc_support() be a static function, which is
  called only from drivers/acpi/pci_root.c.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Tested-by: NAndrew Patterson <andrew.patterson@hp.com>
Acked-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If MSI-X interrupt mode is used by the PCI Express port driver, too
many vectors are allocated and it is not ensured that the right
vectors will be used for the right services.  Namely, the PCI Express
specification states that both PCI Express native PME and PCI Express
hotplug will always use the same MSI or MSI-X message for signalling
interrupts, which implies that the same vector will be used by both
of them.  Also, the VC service does not use interrupts at all.
Moreover, is not clear which of the vectors allocated by
pci_enable_msix() in the current code will be used for PME and
hotplug and which of them will be used for AER if all of these
services are configured.

For these reasons, rework the allocation of interrupts for PCI
Express ports so that if MSI-X are enabled, the right vectors will be
used for the right purposes.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce new function pci_msix_table_size() returning the size of
the MSI-X table of given PCI device or 0 if the device doesn't
support MSI-X.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCI Express port driver uses 'struct pcie_port_service_id' for
matching port service devices and drivers, but this structure
contains fields that duplicate information from the port device
itself (vendor, device, subvendor, subdevice) and fields that are not
used by any existing port service driver (class, class_mask,
drvier_data).  Also, both existing port service drivers (AER and
PCIe HP) don't even use the vendor and device fields for device
matching.  Therefore 'struct pcie_port_service_id' can be removed
altogether and the only useful members of it (port_type, service) can
be introduced directly into the port service device and port service
driver structures.  That simplifies the code quite a bit and reduces
its size.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The second argument of the ->probe() callback in
struct pcie_port_service_driver is unnecessary and never used.
Remove it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCI Express port driver should not attempt to register service
devices that require the ability to generate interrupts if generating
interrupts is not possible.  Namely, if the port has no interrupt pin
configured and we cannot set up MSI or MSI-X for it, there is no way
it can generate interrupts and in such a case the port services that
rely on interrupts (PME, PCIe HP, AER) should not be enabled for it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

PCI Express port driver extension, as defined by struct
pcie_port_device_ext in portdrv.h, is allocated and initialized, but
never used (it also is never freed).  Extend it to hold the PCI Express
port type as well as the port interrupt mode, change its name and use it
to simplify the code in portdrv_core.c .

Additionally, remove the redundant interrupt_mode member of struct
pcie_device defined in include/linux/pcieport_if.h .
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Since creating a device node is normally an operation requiring special
privilege, Igor Zhbanov points out that it is surprising (to say the
least) that a client can, for example, create a device node on a
filesystem exported with root_squash.

So, make sure CAP_MKNOD is among the capabilities dropped when an nfsd
thread handles a request from a non-root user.
Reported-by: NIgor Zhbanov <izh1979@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>

Stricter gfp_mask might be required for clone allocation.
For example, request-based dm may clone bio in interrupt context
so it has to use GFP_ATOMIC.
Signed-off-by: NKiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

dma_map_sg could return a value different to 'nents' argument of
dma_map_sg so the ide stack needs to save it for the later usage
(e.g. for_each_sg).

The ide stack also needs to save the original sg_nents value for
pci_unmap_sg.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[bart: backport to Linus' tree]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This is a fix for the following crash observed in 2.6.29-rc3:
http://lkml.org/lkml/2009/1/29/150

On ARM it doesn't make sense to trace a naked function because then
mcount is called without stack and frame pointer being set up and there
is no chance to restore the lr register to the value before mcount was
called.
Reported-by: NMatthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: NMatthias Kaehlcke <matthias@kaehlcke.net>

Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@home.goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This allows us to change the representation (to a dangling bitmap or
cpumask_var_t) without breaking all the callers: they can use
mm_cpumask() now and won't see a difference as the changes roll into
linux-next.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This allows us to change the representation (to a dangling bitmap or
cpumask_var_t) without breaking all the callers: they can use
tsk_cpumask() now and won't see a difference as the changes roll into
linux-next.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Clean up/micro-optimatization:  Make the AF_INET-only version of
nlm_cmp_addr() smaller.  This matches the style of
nlm_privileged_requester(), and makes the AF_INET-only version of
nlm_cmp_addr() nearly the same size as it was before IPv6 support.
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Fix a memory leak due to allocation in the XDR layer. In cases where the
RPC call needs to be retransmitted, we end up allocating new pages without
clearing the old ones. Fix this by moving the allocation into
nfs3_proc_setacls().

Also fix an issue discovered by Kevin Rudd, whereby the amount of memory
reserved for the acls in the xdr_buf->head was miscalculated, and causing
corruption.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

This reverts commit e088e4c9.

Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.

Course of action:
 - Find out the remaining causes of overheating, and fix them
   if possible. ACPI should be doing the right thing automatically.
   If it isn't, we need to fix that.
 - mark p4-clockmod ui as deprecated
 - try again with the removal in six months.

It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
Signed-off-by: NDave Jones <davej@redhat.com>

Protocol 0x37 has been reserved for iNexio devices and Sahara
was supposed to get 0x38.
Reported-by: NClaudio Nieder <private@claudio.ch>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Declare CFA specific identify data words 162 and 163 for future use.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
[bart: update patch summary/description]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

HDIO_GET_IDENTITY returns 256 words currently.

Noticed by Norman Diamond.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NStanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <linux@maxim.org.za>
[bart: minor checkpatch.pl / CodingStyle fixups]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ap->sector_buf is used as DMA target and should at least be aligned on
cacheline.  This caused problems on some embedded machines.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

libata passes the returned value of dma_map_sg() to
dma_unmap_sg(),which is the misuse of dma_unmap_sg().

DMA-mapping.txt says:

To unmap a scatterlist, just call:

	pci_unmap_sg(pdev, sglist, nents, direction);

Again, make sure DMA activity has already finished.

PLEASE NOTE:  The 'nents' argument to the pci_unmap_sg call must be
              the _same_ one you passed into the pci_map_sg call,
	      it should _NOT_ be the 'count' value _returned_ from the
              pci_map_sg call.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This fixes problems during resume with drives that take longer than 1s to
be ready.  The ATA-6 spec appears to allow 5 seconds for a drive to be
ready.

On one affected system, this patch changes "PM: resume devices took..."
message from 17 seconds to 4 seconds, and gets rid of a lot of ugly
timeout/error messages.

Without this patch, the libata code moves on after 1s, tries to send a
soft reset (which the drive doesn't see because it isn't ready) which also
times out, then an IDENTIFY command is sent to the drive which times out,
and finally the error handler will try to send another hard reset which
will finally get things working.
Signed-off-by: NStuart Hayes <stuart_hayes@dell.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.

Add a netdev_resync_ops() and call it from the vlan code.

Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.

With help from Patrick McHardy.
Tested-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>