Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 12 10月, 2017 2 次提交
  3. 10 10月, 2017 4 次提交
    • I
      Bluetooth: btbcm: Add support for MINIX Z83-4 based devices · 18a39b9a
      由 Ian W MORRISON 提交于 
      The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip
for wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4
with BCM4345 rev C0 firmware.

This patch defines the firmware subversion.
Signed-off-by: NIan W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      18a39b9a
    • I
      Bluetooth: hci_bcm: Add support for MINIX Z83-4 based devices · 1bdb68b2
      由 Ian W MORRISON 提交于 
      The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip for
wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4 with
BCM4345 rev C0 firmware.

This patch adds the device id and to use trigger type IRQF_TRIGGER_FALLING
as defined by 'GpioInt' in the ACPI DSDT table:

    Device (BLT0)
    {
        Name (_HID, "BCM2EA4")  // _HID: Hardware ID
        Method (_STA, 0, NotSerialized)  // _STA: Status
        {
            Return (0x0F)
        }

        Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
        {
            Name (UBUF, ResourceTemplate ()
            {
                UartSerialBusV2 (0x0001C200, DataBitsEight, StopBitsOne,
                    0xFC, LittleEndian, ParityTypeNone, FlowControlHardware,
                    0x0020, 0x0020, "\\_SB.PCI0.URT1",
                    0x00, ResourceConsumer, , Exclusive,
                    )
                GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000,
                    "\\_SB.GPO1", 0x00, ResourceConsumer, ,
                    )
                    {   // Pin list
                        0x0005
                    }
                GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
                    "\\_SB.GPO1", 0x00, ResourceConsumer, ,
                    )
                    {   // Pin list
                        0x0007
                    }
                GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
                    "\\_SB.GPO1", 0x00, ResourceConsumer, ,
                    )
                    {   // Pin list
                        0x0004
                    }
            })
            Return (UBUF) /* \_SB_.PCI0.URT1.BLT0._CRS.UBUF */
        }
    }
Signed-off-by: NIan W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      1bdb68b2
    • J
      Bluetooth: avoid silent hci_bcm ACPI PM regression · 4294625e
      由 Johan Hovold 提交于 
      The hci_bcm platform-device hack which was used to implement
power management for ACPI devices is being replaced by a
serial-device-bus implementation.

Unfortunately, when the corresponding change to the ACPI code lands (a
change that will stop enumerating and registering the serial-device-node
child as a platform device) PM will break silently unless serdev
TTY-port controller support has been enabled. Specifically, hciattach
(btattach) would still succeed, but power management would no longer
work.

Although this is strictly a runtime dependency, let's make the driver
depend on SERIAL_DEV_CTRL_TTYPORT, which is the particular serdev
controller implementation used by the ACPI devices currently managed by
this driver, to avoid breaking PM without anyone noticing.

Note that the driver already has a (build-time) dependency on the serdev
bus code.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      4294625e
    • I
      Bluetooth: hci_bcm: Correct context of IRQ polarity message · e8bfe868
      由 Ian W MORRISON 提交于 
      As the overwriting of IRQ polarity to active low occurs during the driver
probe using 'bt_dev_warn' to display the warning results in '(null)' being
displayed for the device. This patch uses 'dev_warn' to correctly display
the device in the warning instead.
Signed-off-by: NIan W MORRISON <ianwmorrison@gmail.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      e8bfe868
  5. 07 10月, 2017 13 次提交
  7. 18 8月, 2017 2 次提交
    • M
      Bluetooth: hci_bcm: Handle empty packet after firmware loading · 01d5e44a
      由 Marcel Holtmann 提交于 
      The Broadcom controller on the Raspberry Pi3 sends an empty packet with
packet type 0x00 after launching the firmware. This will cause logging
of errors.

  Bluetooth: hci0: Frame reassembly failed (-84)

Since this seems to be an intented behaviour of the controller, handle
it gracefully by parsing that empty packet with packet type 0x00 and
then just simply report it as diagnostic packet.

With that change no errors are logging and the packet itself is actually
recorded in the Bluetooth monitor traces.

  < HCI Command: Broadcom Launch RAM (0x3f|0x004e) plen 4
         Address: 0xffffffff
  > HCI Event: Command Complete (0x0e) plen 4
       Broadcom Launch RAM (0x3f|0x004e) ncmd 1
         Status: Success (0x00)
  = Vendor Diagnostic (len 0)
  < HCI Command: Broadcom Update UART Baud Rate (0x3f|0x0018) plen 6
         00 00 00 10 0e 00                                ......
  > HCI Event: Command Complete (0x0e) plen 4
       Broadcom Update UART Baud Rate (0x3f|0x0018) ncmd 1
         Status: Success (0x00)
  < HCI Command: Reset (0x03|0x0003) plen 0
  > HCI Event: Command Complete (0x0e) plen 4
       Reset (0x03|0x0003) ncmd 1
         Status: Success (0x00)
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
      01d5e44a
    • L
      Bluetooth: hci_bcm: Add serdev support · 33cd149e
      由 Loic Poulain 提交于 
      Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.

Tested/compatible with bcm43438 (RPi3).
Signed-off-by: NLoic Poulain <loic.poulain@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      33cd149e
  9. 17 8月, 2017 1 次提交
  11. 16 8月, 2017 2 次提交
    • M
      Bluetooth: hci_bcm: Use operation speed of 4Mbps only for ACPI devices · 74183a1c
      由 Marcel Holtmann 提交于 
      Not all Broadcom controller support the 4Mbps operational speed on UART
devices. This is because the UART clock setting changes might not be
supported.

  < HCI Command: Broadcom Write UART Clock Setting (0x3f|0x0045) plen 1
         01                                               .
  > HCI Event: Command Complete (0x0e) plen 4
       Broadcom Write UART Clock Setting (0x3f|0x0045) ncmd 1
         Status: Unknown HCI Command (0x01)

To support any operational speed higher than 3Mbps, support for this
command is required. With that respect it is better to not enforce any
operational speed by default. Only when its support is known, then allow
for higher operational speed.

This patch assigns the 4Mbps opertional speed only for devices
discovered through ACPI and leave all others at the default 115200.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
      74183a1c
    • S
      Bluetooth: btusb: driver to enable the usb-wakeup feature · a0085f25
      由 Sukumar Ghorai 提交于 
      BT-Controller connected as platform non-root-hub device and
usb-driver initialize such device with wakeup disabled,
Ref. usb_new_device().

At present wakeup-capability get enabled by hid-input device from usb
function driver(e.g. BT HID device) at runtime. Again some functional
driver does not set usb-wakeup capability(e.g LE HID device implement
as HID-over-GATT), and can't wakeup the host on USB.

Most of the device operation (such as mass storage) initiated from host
(except HID) and USB wakeup aligned with host resume procedure. For BT
device, usb-wakeup capability need to enable form btusc driver as a
generic solution for multiple profile use case and required for USB remote
wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature
need to enable/disable with HCI interface up and down.
Signed-off-by: NSukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: NAmit K Bag <amit.k.bag@intel.com>
Acked-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      a0085f25
  13. 15 8月, 2017 1 次提交
    • M
      Bluetooth: btusb: Add workaround for Broadcom devices without product id · 9834e586
      由 Marcel Holtmann 提交于 
      The GPD Pocket is shipping with a BCM2045 USB HCI with its vendor and
product information set to 0000:0000 and also has its interface class
set to 255 (Vendor Specific Class). Luckily it does advertise usable
manufacturer and product strings.

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM2045A0
S:  SerialNumber=AC83F30677CB
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Reported-by: NChristopher Williamson <home@chrisaw.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
      9834e586
  15. 08 8月, 2017 2 次提交
    • D
      Bluetooth: Add support of 13d3:3494 RTL8723BE device · a81d72d2
      由 Dmitry Tunin 提交于 
      T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3494 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
      a81d72d2
    • O
      Bluetooth: bluecard: blink LED during continuous activity · c7ab7330
      由 Ondrej Zary 提交于 
      Currently the activity LED is solid on during continuous activity.
Blink the LED during continuous activity to match Windows driver
behavior.

Cards with activity LED:
power LED = solid on when up, off when down
activity LED = blinking during activity, off when idle

Cards without activity LED:
power LED = solid on when up, off when down, blinking during activity
(don't have such a card so I don't know if Windows driver does the same
thing)
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
      c7ab7330
  17. 07 8月, 2017 2 次提交
  19. 01 8月, 2017 1 次提交
  21. 31 7月, 2017 1 次提交
  23. 29 7月, 2017 1 次提交
  25. 25 7月, 2017 2 次提交
  27. 22 7月, 2017 1 次提交
  29. 20 7月, 2017 5 次提交