The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.

But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.

So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Acked-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: NRicardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM571x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM572x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With two separate &gpmc nodes the second ranges property overwrites the
first. So put nand and ethernet in a single node and merge the ranges.

While at it also fix the ethernet suffix.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.

So remove the unexisting 'enable-active-low' property.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If we have Linux installed in eMMC we can boot without
µSD card, but inserting one is not recognised.

The reason is that the card detect gpio (gpio5_152)
is not configured and attached to the mmc1 interface
driver and the mmc driver does not poll by default.

Hence we add pinmux and gpio setup for the SDCARD_NCD
signal.
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Droid 4 has WL 1285C connected to the OMAP's UART4 port, which is
used for Bluetooth and most likely can also be used for controlling
the FM radio and GPS receivers.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.

We don't want to use the OTG controller block on this
platform as it limits host mode to high-speed. Instead
we rely on extcon framework to give us ID events for
dual-role mode detection.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NRob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>

The SPEAr600 has a built-in ADC, which already has a Device Tree binding
described in
Documentation/devicetree/bindings/staging/iio/adc/spear-adc.txt. This
commit adds the description in the SPEAr600 Device Tree of this ADC
device.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The spear6xx doesn't have a pinctrl driver, since the pinmux is globally
defined through a single register, generally configured by the
firmware/bootloader.

Therefore, the pinctrl related properties in spear600-evb.dts are not
necessary.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This commit moves spear600-evb.dts to use the new flash partition Device
Tree binding documented in
Documentation/devicetree/bindings/mtd/partition.txt.

As this Device Tree binding document says: "For backwards compatibility
partitions as direct subnodes of the mtd device are supported. This use
is discouraged."
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This commit fixes a minor coding style issue in spear600-evb.dts:
missing spaces around equal sign.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Now that we have introduced node labels in spear600.dtsi, we can use
them for spear600-evb.dts.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Having labels allows to more easily reference nodes in .dts files
including spear600.dtsi.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch fixes the following set of warnings on vexpress platforms:

 sysreg@010000 simple-bus unit address format error, expected "10000"
 sysctl@020000 simple-bus unit address format error, expected "20000"
 i2c@030000 simple-bus unit address format error, expected "30000"
 aaci@040000 simple-bus unit address format error, expected "40000"
 mmci@050000 simple-bus unit address format error, expected "50000"
 kmi@060000 simple-bus unit address format error, expected "60000"
 kmi@070000 simple-bus unit address format error, expected "70000"
 uart@090000 simple-bus unit address format error, expected "90000"
 uart@0a0000 simple-bus unit address format error, expected "a0000"
 uart@0b0000 simple-bus unit address format error, expected "b0000"
 uart@0c0000 simple-bus unit address format error, expected "c0000"
 wdt@0f0000 simple-bus unit address format error, expected "f0000"

Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NLiviu Dudau <liviu.dudau@arm.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>

Remove ADC channels that are not available by default on the sama5d3_xplained
board (resistor not populated) in order to not create confusion.
Signed-off-by: NLudovic Desroches <ludovic.desroches@microchip.com>
Cc: <stable@vger.kernel.org> # 3.16+
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The voltage reference for the ADC is not 3V but 3.3V since it is connected to
VDDANA.
Signed-off-by: NLudovic Desroches <ludovic.desroches@microchip.com>
Cc: <stable@vger.kernel.org> # 3.16+
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The envelope detector can analyze 6 different signals, selectable with a
mux controlled by three gpio pins.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.

Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.

Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently most nodes got labels to make them referenceable. The USB 3.0
nodes as well as the nodes for the SATA controllers were left out,
rectify the omission.

The labels "sataX" are already used by some boards for the SATA ports,
therefore use "ahciX" to label the SATA controller nodes.

To avoid potential confusion by labeling an USB3.0 controller "usb2" use
usb3_X as labels. This also coincides with the node names themselves
(usb@xxxxx vs usb3@xxxxx).
Signed-off-by: NRalph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add the new hdmi phandle to exynos4.dtsi. This phandle is needed by the
s5p-cec driver to initialize the CEC notifier framework.

Tested with my Odroid U3.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
CC: linux-samsung-soc@vger.kernel.org
CC: devicetree@vger.kernel.org
CC: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

To use CEC notifier sti CEC driver needs to get phandle
of the hdmi device.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
CC: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The hpd pin of the second hdmi connector of the Utilite Pro is wired
up to a gpio pin of the SoC. Reflect this in the device tree.
Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

On imx6qp-sabresd LDO_ARM is connected to a different PMIC output than
the other imx6qdl-sabresd boards.

Setting cpu0 arm-supply to sw2_reg is wrong, this must have mistakenly
slipped out of the vendor tree where this is are used for LDO bypass.
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Setting the supply is optional but beneficial, it will cause PMIC
voltages to be dynamically changed with cpu frequency.
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Gateworks Ventana GW5903 is a single-board computer based on the NXP
IMX6 SoC with the following features:
 * IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
 * 4GiB DDR3 DRAM
 * 32GB eMMC
 * 1x microSD connector
 * Gateworks System Controller:
  - hardware watchdog
  - hardware monitor
  - pushbutton controller
  - EEPROM storage
  - power control
 * JTAG programmable
 * Inertial Module
 * uBlox EMMY-W1 (bluetooth/nfc/802.11ac)
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The i.MX25 contains two AHB to IP bridges (AIPS), each of which has a set of
control registers. Add the memory regions for the control registers to
the Device Tree.
Signed-off-by: NMartin Kaiser <martin@kaiser.cx>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Model the Carrier Board power distribution by adding a fixed 3.3V
and 5V regulator. The 3.3V regulator is connected to the backlight
as well as the display supply. The 5V regulator is used to supply
USB VBUS.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The ADC is directly supplied by the PMIC 1.8V rail, remove the
superfluous fixed regulator.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The regulator-always-on property on the Ethernet rail prevents Linux
from disabling the rail when Ethernet is shut down (suspend or simply
link down). With this change the regulator framework will disable the
rail when the Ethernet PHY is not used, saving power especially on
carrier board not using Ethernet.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fix wrong voltage of PWR_EN_+V3.3 rail. The error had no noticeable
effect since no consumer explicitly requested a specific voltage.
Also use round voltages as it is common in other device trees.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

https://boundarydevices.com/product/nit6x-som-v2/Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>