Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: NMarco Schluessler <marco@lordzodiac.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
  to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
  client call
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- ELSA EX-VISION 500TV was incorrectly programmed to have the same
  subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
  with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: NMattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a 
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: NRicardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: NKarsten Suehring <ksuehring@gmx.net>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
  to remove some code duplication
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- use one Author per line, which allows us to add more
  authors later without creating a mess.
- Add Michael Krufky due to -git commit
	2cbeddc9Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

RTC_IRQP_SET/RTC_EPOCH_SET don't take a pointer to an argument, but the
argument itself.  This actually simplifies the code and makes it work.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The previous experiment for using apicmaintimer on ATI systems didn't
work out very well.  In particular laptops with C2/C3 support often
don't let it tick during idle, which makes it useless.  There were also
some other bugs that made the apicmaintimer often not used at all.

I tried some other experiments - running timer over RTC and some other
things but they didn't really work well neither.

I rechecked the specs now and it turns out this simple change is
actually enough to avoid the double ticks on the ATI systems.  We just
turn off IRQ 0 in the 8254 and only route it directly using the IO-APIC.

I tested it on a few ATI systems and it worked there.  In fact it worked
on all chipsets (NVidia, Intel, AMD, ATI) I tried it on.

According to the ACPI spec routing should always work through the
IO-APIC so I think it's the correct thing to do anyways (and most of the
old gunk in check_timer should be thrown away for x86-64).

But for 2.6.16 it's best to do a fairly minimal change:
 - Use the known to be working everywhere-but-ATI IRQ0 both over 8254
   and IO-APIC setup everywhere
 - Except on ATI disable IRQ0 in the 8254
 - Remove the code to select apicmaintimer on ATI chipsets
 - Add some boot options to allow to override this (just paranoia)

In 2.6.17 I hope to switch the default over to this for everybody.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

SMP time selection originally ran after all CPUs were brought up because
it needed to know the number of CPUs to decide if it needs an MP safe
timer or not.

This is not needed anymore because we know present CPUs early.

This fixes a couple of problems:
 - apicmaintimer didn't always work because it relied on state that was
   set up time_init_gtod too late.
 - The output for the used timer in early kernel log was misleading
   because time_init_gtod could actually change it later.  Now always
   print the final timer choice
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It didn't set up the CPU possible map early enough, so the
option didn't actually work.

Noticed by Heiko Carstens
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ACPI is initialized very early on x86-64, before the DMI code is
initialized.  This means it would often discover a 0 year and then turn
off ACPI because it thought the BIOS was too old.  Some systems don't
boot without ACPI so this was a problem.

I have a full fix by adding new very early DMI detection, but it needs
more testing before it can be merged.  For 2.6.16 let's just turn the
check off.  It never made much sense anyways because there are no x86-64
systems older than 2002 or so and they generally all have working ACPI.

Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[description from AK]

Old check for the IO-APIC watchdog during the timer check was wrong -
it obviously should only drop into this if the IO-APIC watchdog is used.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This makes x86-64 use the common X86_PM_TIMER Kconfig entry in drivers/acpi

And since PM timer is needed for correct timing on a lot of systems
now (e.g. AMD dual cores) and we often get bug reports from people
who forgot to set it make it depend on CONFIG_EMBEDDED. x86-64 had
this change before and it's a good thing.

I also fixed the description slightly to make this more clear.

Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[description from AK]

This fixes booting in APIC mode on some ACER laptops. x86-64
did a similar change some time ago.

See http://bugzilla.kernel.org/show_bug.cgi?id=4700 for details
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Big Unisys systems have multiple clusters too, but they have an
synchronized TSC.

I'm using the SMBIOS to check for vendor == IBM.

Cc: Chris McDermott <lcm@us.ibm.com>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixes a local DOS on Intel systems that lead to an endless
recursive fault.  AMD machines don't seem to be affected.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The value, while currently unused in the native kernel, was off by one.
Signed-Off-By: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In previous versions of pci-gart.c, no_iommu was used to determine if IOMMU was
disabled in the GART DMA mapping functions.  This changed in 2.6.16 and now
gart_xxx() functions are only called if gart is enabled.  Therefore, uses of
no_iommu in the GART code are no longer necessary and can be removed.

Also, it removes double deceleration of no_iommu and force_iommu in pci.h and
proto.h, by removing the deceleration in pci.h.

Lastly, end_pfn off by one error.

Tested (along with patch 1/2) on dual opteron with gart enabled, iommu=soft,
and iommu=off.
Signed-off-by: NJon Mason <jdmason@us.ibm.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

As the (probably) last user of a Specialix SI board, I noticed that
recent kernels would fail to probe the sucker.  Quick investigation
indicate a few missing braces...

I left the double probing in place, as it looks like it's been here
forever.
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There's a problem in sd where we blindly believe the length of the
headers and block descriptors.  Some devices return insane values for
these and cause our length to end up greater than the actual buffer
size, so check to make sure.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Also removed the buffer size magic number (512) and added DPOFUA of
zero to the defaults
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Commit 9c869eda moved the i386 topology.c
file. That change broke x86-64 compiles, as it uses the same file.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

mem= command line option was being ignored in arch/powerpc if we were not
a CONFIG_MULTIPLATFORM (which is handled via prom_init stub). The initial
command line extraction and parsing needed to be moved earlier in the boot
process and have code to actual parse mem= and do something about it.

Also, fixed a compile warning in the file.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NSegher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When compiling a non-default subarch, topology.c is missing from the kernel
build.  This causes builds with CONFIG_HOTPLUG_CPU to fail.  In addition,
on Intel processors with cpuid level > 4, it causes intel_cacheinfo.c to
reference uninitialized data that should have been set up by the initcall
in topology.c which calls register_cpu.  This causes a kernel panic on boot
on newer Intel processors.  Moving topology.c to arch/i386/kernel fixes
both of these problems.

Thanks to Dan Hecht for finding and fixing this problem.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NDan Hecht <dhect@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

akpm points out that switching to a non-NUMA kernel could be irritating
if mounting tmpfs fails on an mpol option: tmpfs.txt recommend remount.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Minor number should be freed after del_gendisk().  Otherwise, there could
be a window where 2 registered gendisk has same minor number.
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: NAlasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Need to unfreeze and release bdev otherwise the bdev inode with
inconsistent state is reused later and cause problem.
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: NAlasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Phil Marek <philipp.marek@bmlv.gv.at> points out that ramfs forgets to update
a directory's mtime and ctime when it is modified.

Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>