Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NTang Yuantian <b29983@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
    - x1 PCIe slot or x1 PCIe to dual SATA controller
    - x1 mini-PCIe slot
USB 2.0
    - ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic’s GL850A
    - Two USB2.0 Type A receptacles
    - One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NMatthew McClintock <msm@freescale.com>
Signed-off-by: NXu Jiucheng <B37781@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The FreeScale PowerQUICC-III-compatible (mpc85xx/mpc86xx) MPICs do not
correctly report the number of hardware interrupt sources, so software
needs to override the detected value with "256".

To avoid needing to write custom board-specific code to detect that
scenario, allow it to be easily overridden in the device-tree.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The Freescale MPIC (and perhaps others in the future) is incapable of
routing non-IPI interrupts to more than once CPU at a time.  Currently
all of the Freescale boards msut pass the MPIC_SINGLE_DEST_CPU flag to
mpic_alloc(), but that information should really be present in the
device-tree.

Older board code can't rely on the device-tree having the property set,
but newer platforms won't need it manually specified in the code.

[BenH: Remove unrelated changes, folded in a different patch]
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The MPIC code checks for a "big-endian" property and sets the flag
MPIC_BIG_ENDIAN if one is present, although prior to the "mpic->flags"
fixup that would never have worked anways.

Unfortunately, even now that it works properly, the Freescale mpic
device-node (the "PowerQUICC-III"-compatible one) does not specify it,
so all of the board ports need to manually pass it to mpic_alloc().

Document the flag and add it to the pq3 device tree.  Existing code will
still need to pass the MPIC_BIG_ENDIAN flag because their dtb may not
have this property, but new platforms shouldn't need to do so.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add usb2 controller node for P1020RDB, P2020RDB, P2020DS, P1021MDS
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable USB2 controller node for P1020RDB. USB2 controller is used only
when board boots from SPI or SD as it is muxed with eLBC
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

According to latest kernel, the auto-cmd12 property should be
"sdhci,auto-cmd12", and according to the SDHC binding and the workaround for
the special chip, add the chip compatible for eSDHC: "fsl,p1022-esdhc",
"fsl,mpc8536-esdhc", "fsl,p1020-esdhc", "fsl,p2020-esdhc" and
"fsl,p1010-esdhc".
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This hooks dtc into Kbuild's dependency system.

Thus, for example, "make dtbs" will rebuild tegra-harmony.dtb if only
tegra20.dtsi has changed yet tegra-harmony.dts has not. The previous
lack of this feature recently caused me to have very confusing "git
bisect" results.

For ARM, it's obvious what to add to $(targets). I'm not familiar enough
with other architectures to know what to add there. Powerpc appears to
already add various .dtb files into $(targets), but the other archs may
need something added to $(targets) to work.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
[mmarek: Dropped arch/c6x part to avoid merging commits from the middle
of the merge window]
Signed-off-by: NMichal Marek <mmarek@suse.cz>

The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features.  Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

PCI ranges, localbus reg and localbus chip-select 2 range do not match
the memory map setup by bootloader.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.

The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

commit c55aef0e ("powerpc/boot: Change the load address
for the wrapper to fit the kernel") introduced a WARNING to
inform the user that the uncompressed kernel would overlap
the boot uncompressing wrapper code. Change it to an INFO.

I initially thought, this would be a 'WARNING' for the those
boards, where the link_address should be fixed, so that the
user can take actions accordingly.

Changing the same to INFO.
Signed-off-by: NSuzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The wrapper code which uncompresses the kernel in case of a 'ppc' boot
is by default loaded at 0x00400000 and the kernel will be uncompressed
to fit the location 0-0x00400000. But with dynamic relocations, the size
of the kernel may exceed 0x00400000(4M). This would cause an overlap
of the uncompressed kernel and the boot wrapper, causing a failure in
boot.

The message looks like :

   zImage starting: loaded at 0x00400000 (sp: 0x0065ffb0)
   Allocating 0x5ce650 bytes for kernel ...
   Insufficient memory for kernel at address 0! (_start=00400000, uncompressed size=00591a20)

This patch shifts the load address of the boot wrapper code to the next
higher MB, according to the size of  the uncompressed vmlinux.

With the patch, we get the following message while building the image :

 WARN: Uncompressed kernel (size 0x5b0344) overlaps the address of the wrapper(0x400000)
 WARN: Fixing the link_address of wrapper to (0x600000)
Signed-off-by: NSuzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

Based on original work by David 'Shaggy' Kleikamp.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

Needed for currituck support.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.

I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float.  Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel.  So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S  I don't think this code changes too often ;P
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.

This adds it using ppc40x_simple and provides a device-tree.

There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.

The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.

CC: devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.
Signed-off-by: NTanmay Inamdar <tinamdar@apm.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.

In this situation, the pixis supports "indirect mode", which allows access
to the pixis itself by reading/writing addresses on specific local bus
chip selects.  CS0 is used to select which pixis register to access, and
CS1 is used to read/write the value.

To support this, we introduce another board-control child node of the
localbus node that contains a 'reg' property for CS0 and CS1.  This will
produce the correct physical addresses for CS0 and CS1.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Update all dts files that support SRIO controllers to match the new
fsl,srio device tree binding.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p5020-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p4080-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3060-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
* Fixed l3-cache IRQs, we have 2 CPCs, so we should have IRQs for both
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Fixed some dcsr compatiable typo's from 'p43041' to 'p3041'
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p2041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
  moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
 'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 &
* etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
 'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 & etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1023-IP..." from compatibles for standard blocks
* Removed incorrect power/pmc node, there are no etsec on P1023
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
  'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Updated spi node to new espi binding specification
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1022-IP..." from compatibles for standard blocks
* Fixed bug in local bus range node for CS2, was maping to
  0x0 0x0xffa00000 instead of 0xf 0xffa00000
* Fixed localbus reg property should have been 0xf 0xffe05000
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Tested-by: NTimur Tabi <timur@freescale.com>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
  moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Dropping "fsl,p1020-IP..." from compatibles for standard blocks
* Fixed PCIe interrupt-maps to have proper number of cells
* Added mdio node for etsec@26000
* Added usb node for 2nd usb controller
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1010-IP..." from compatibles for standard blocks
* PCI interrupt map - wrong IRQs for PCI-0 controller
* SDHC interrupt sense was wrong
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
  moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8572 SoC template
* Dropping "fsl,mpc8572-IP..." from compatibles for standard blocks
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Dropping "fsl,mpc8569-IP..." from compatibles for standard blocks
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>