FFT spectral scan is a functionality that makes sense to have its own
debug flag.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

* Interrupt request need to happen when the wilink chip is powered on and
  driving the wlan_irq line. This avoids spurious interrupt issues that
  are a result of different external pulls configuration on different
  platforms
* Allow working with wl18xx level-low and falling edge irqs by configuring
  wl18xx to invert the device interrupt
Signed-off-by: NEyal Reizer <eyalr@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fix some spelling typo in drivers/net/wirless
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We will reset more_task_flag at the end of main process
routine. This optimization will help to remove spinlock
operations at couple of places in the code.
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On some BCM5301x ARM devices, user space still needs to control some
system GPIO pins for which no driver exists. This is a lot easier to do
with a predictable GPIO base.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With PCIE it is possible to support multiple devices with the
same device type. They all load the same nvram file. In order to
support this the nvram can specify which part of the nvram is
for which pcie device. This patch adds support for these new
types of nvram files.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for the BCM4358 2x2 11ac device.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

commit 330b4e4b ("brcmfmac: Add wowl support for SDIO devices.")
changed the behaviour by removing the MMC_PM_KEEP_POWER flag for
non-wowl scenario, which needs to be restored. Another necessary
change is to mark the card as being non-removable. With this in place
the suspend resume test passes successfully doing:

 # echo devices > /sys/power/pm_test
 # echo mem > /sys/power/state

Note that power may still be switched off when system is going
in S3 state.
Reported-by: NFu, Zhonghui <&lt;zhonghui.fu@linux.intel.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the sdio bus state is not ready to process we abort the
interrupt service routine. This is not wanted as it keeps the
interrupt source active. Better clear the interrupt source.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for the BCM4324 B5 revision. This device
is similar to BCM43241 from driver and firmware perspective. It
is known to be used in Lenovo Thinkpad Tablet devices.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The scheduled scan support depends on firmware supporting the PNO
feature. This feature is optional so add a feature flag for this
in the driver and announce scheduled scan support accordingly.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some feature flags were not described in the header file. Adding
the description.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When change the country code the available channels may change. So
the wiphy bands should be updated accordingly.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver was constructing a list of channels per wiphy band
by querying the device. This list is not what the hardware is
able to do as it is already filtered by the country setting in
the device. As user-space may change the country this would
require updating the channel list which is not recommended [1].
This patch introduces a superset of channels. The individual
channels are disabled appropriately by querying the device.

[1] http://mid.gmane.org/1426706320.3001.21.camel@sipsolutions.netReviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes an issue where it was discovered that driver is setting
invalid HT IEs to FW. This was happening because bug in parsing HT IE.
Driver would incorrectly point to start of HT IE while FW only needs actual
HT configuration - excluding EID and length.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch reverts 'commit c5534844 ("mwifiex:
enable aggregation for TID 6 and 7 streams")'.
TID6 & TID7 is voice traffic which is quite time sensitive.
Do not enable any type of aggregation on these TIDs.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2015-05-03' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure

Fix a copy paste bug that didn't copy wildcard SSIDs to
scan requests. This bug causes scan with only wildcard
SSID to be passive, and scans with more than one SSID to
send only the direct probes.

Fixes: 2a28ac14c518 ("iwlwifi: mvm: add common scan params to thw iwl_mvm_scan_params struct")
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some more tidbits left over from the legacy scan removal.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The thermal throttling parameters were constant and hardcoded, not allowing
changes for different NIC families.
Change this so that the values are part of the NIC family configuration and
are not constant (so they can be changed dynamically in the future).
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When a firmware restart is done, don't try to reprogram the keys to new
slots but rather just keep the old key index, while skipping keys that
weren't programmed before.

Not only does this restore the state more faithfully, but it will also
allow using the HW key index for internal purposes as an array index.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The generic scan command functions are now irrelevant, since both
sched and regular scans are in the same code.  So rename this
functions to dwell and isolate all the dwell-related setting to them.
Keeping the dwell code separate makes it easier to compare the LMAC
and UMAC versions.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Having an LMAC counterpart for the existing UMAC flags function makes
things more consistent and easy to compare and spot the differences.
The flags are the same, but are in different bits, so unfortunately we
can't use a single function for both APIs.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Clean the code a little by moving all the flags into the right
function.  Additionally, rename the function, since "common" is now
irrelevant.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we use an external buffer, it is allocated from the
t DRAM and can be as big as 64MB. This buffer is huge and
might not be needed for the specific issue being chased.
Especially if lots of dumps are going to be created.
Allow to limit the size of the buffer in the configuration.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

qos_seq points (to a struct) inside the command response data.

Make sure to free the response only after qos_seq is not
needed anymore.

type=bugfix
bug=not-tracked
fixes=I78c07110b59dcd389207bd2b168b0a2760839fe0

Change-Id: I619ce2c17e064dc98c7be9abc1e23175fdc8fb9a
Reported-by: NHeng Luo <heng.luo@intel.com>
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/r/55381Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: IWL Jenkins
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

With just a few differences left in the UMAC scan functions now, we
can merge them into one, taking care of the small difference according
to the total number of iterations required.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In theory, LMAC scans can handle a 32-bit delay, but since waiting for
over 18 hours to start the scan is a bit silly and to keep it aligned
with UMAC scans (which only support 16-bit delays), trim it down to
16-bits.

This makes the LMAC vs. UMAC and the UMAC reg scan vs. UMAC sched scan
code more similar.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The last remaining difference between the regular scan and scheduled
scan flows for LMAC is the FW capabilities check for EBS scans.

Merge these checks into a new function and then combine the LMAC scan
functions into a single one.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As another step towards combining the scan and sched scan functions,
add parameters that tell the scan function how many iterations we want
(i.e. 1 for normal scan, more for scheduled scan) and that set the
full scan multiplier (only meaningful for LMAC).
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The probe request to be added to both LMAC and UMAC scan commands are
identical, so move the generation out of the LMAC/UMAC-specific code.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

To make things clearer, rename the iwl_mvm_scan_calc_params() function
to iwl_mvm_calc_dwell() and make it calculate and fill in only
dwell-related parameters.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Now that both scheduled scan and regular scan SSID populating
functions do the same thing, they can be combined into a single
function.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware inverts the order of the SSIDs sent out in probe requests
(for some reason).  For regular scans, we've been passing the SSIDs in
the opposite order so they go out in the order we want.  With
scheduled scans, we were not doing that, so they were sent out in
reverse order of priority.  Fix that by using the reverse order when
populating the SSIDs array for scheduled scans as well.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The only difference in the ssid_bitmap between LMAC and UMAC scans is
that in LMAC bits 1 to 20 are used, while in UMAC bits 0 to 19 are
used (*sigh*).  So we can combine the bitmap creation into a single
function and simply shift left if LMAC is used.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Many parameters are common for all scans.  Instead of parsing the
cfg80211 scan and sched scan requests differently in each flow, move
the parsing outside of the API/scan-type specific functions.  In this
way, we only need to differentiate between scan types once.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Similarly to the regular scan patch, a lot of the UMAC and LMAC sched
scan code is also almost identical.  Grab the low hanging fruits by
combining the obvious parts.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>