The a23-ippo-q8h tablets have volume up/down buttons using the lradc. This
has been tested on both a v5 and a v1.2 tablet.
Tested-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A23 has the same lradc controller as previous Allwinner SoCs.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.

The regulator names and constraints are based on the board
schematics and the SoC datasheet.

DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.

Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.

The regulator names and constraints are based on the board
schematics and the SoC datasheet.

DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.

LDO3 powers the USB WiFi module. This patch also references it
from the usb-phy node.

Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.

The regulator names and constraints are based on the board
schematics and the SoC datasheet.

DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.

Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.

The regulator names and constraints are based on the board
schematics and the SoC datasheet.

DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.

Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The AXP209 PMIC is used with some Allwinner SoCs. This patch adds
a dtsi file listing all the regulator nodes. The regulators are
initialized based on their device node names.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pcDuino board has LEDs connected to PH15/PH16, and back/home/menu
buttons to PH17/18/19 respectively. Enable these via gpio-leds and
gpio-keys. This is shared across the v1 and v2 versions of the board.

Tested on a v2 and verified against the schematics of a v1.
Signed-off-by: NZoltan HERPAI <wigyori@uid0.hu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
[Maxime: Added some newlines between the button nodes]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add simplefb nodes for "[de_fe0-]de_be0-lcd0" and "[de_fe0-]de_be0-lcd0-tve0"
display pipelines for when u-boot has set up a pipeline to drive a LCD panel /
VGA output rather then the HDMI output.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.

The operating points were taken from the A10 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.

The operating points were taken from the A13 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.

The operating points were taken from the A20 FEX files in the
sunxi-boards repository. Not all boards have the same settings. The
settings in this patch are the most generic ones.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that the resistive touchpanel driver supports thermal sensors,
add the "#thermal-sensor-cells" property as required by the thermal
framework.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The NMI IRQ controller uses the standard flags definition for the IRQ level and
edges.

Use the common header to use defines instead of opaque numbers.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The GIC requires some extra opaque arguments to set the IRQ type and flags.

Convert the DTs to using the common defines.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.

Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The DMA engine for the A10/A20 and derivatives require an opaque extra
argument.

Add a dt-bindings header, and convert the device trees to it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Prepare the device trees to use the C preprocessor.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out.

Note it has no sdcard slot and therefore can only be fel booted.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a dtsi file for A31s based boards.

Since the  A31s is the same die as the A31 in a different package, this dtsi
simply includes sun6i-a31.dtsi and then overrides the pinctrl compatible to
reflect the different package, everything else is identical.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Mele M9 has an ir receiver, enable it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node for the ir receiver found on the A31.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[Maxime: Added a node label]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add an ir_clk sub-node to the prcm node.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Only SPI0 is enabled, as the schematic denotes it as the only SPI bus,
while other pins are reserved for different peripherals.
Signed-off-by: NAlexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These are based on the available SPI configurations of Cubieboard,
Olimex LIME, and PcDuino. There is no pin group for SPI3, as all the
boards seem to use those pins for EMAC.
Signed-off-by: NAlexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

On the Hummingbird A31 board, the RTL8211E ethernet phy has its reset
line connect to a gpio pin, instead of floating like on other boards.
Add the stmmac properties for describing the reset gpio.

The reset delays were taken from the RTL8211E datasheet.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add pinmux settings for the ir receive pin of the A31.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.

Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Ippo q8h has its serial console connected to the r-uart. Adjust the
serial0 alias to match.

This fixes the kernel serial console no longer working since 3.19-rc1, because
8250_dw.c now honors dt aliases, causing the serial console to be ttyS5 rather
then being ttyS0, as it was in 3.18 and before.

Note that adjusting bootargs instead is not an acceptable fix, because
console=ttyS0,115200 is used by a lot of bootscripts, etc. and this should
continue to work.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

usbphy0 support in the sunxi usb-phy driver has been merged, but the
dtsi's for sun4i/sun5i haven't been updated. This results in the phy
driver failing to load, breaking usb support.

Fixes: 6827a46f ('phy: sun4i: add support for USB phy0')
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
 "kernel: Provide READ_ONCE and ASSIGN_ONCE

  As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
  ACCESS_ONCE might fail with specific compilers for non-scalar
  accesses.

  Here is a set of patches to tackle that problem.

  The first patch introduce READ_ONCE and ASSIGN_ONCE.  If the data
  structure is larger than the machine word size memcpy is used and a
  warning is emitted.  The next patches fix up several in-tree users of
  ACCESS_ONCE on non-scalar types.

  This does not yet contain a patch that forces ACCESS_ONCE to work only
  on scalar types.  This is targetted for the next merge window as Linux
  next already contains new offenders regarding ACCESS_ONCE vs.
  non-scalar types"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
  s390/kvm: REPLACE barrier fixup with READ_ONCE
  arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
  arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
  mips/gup: Replace ACCESS_ONCE with READ_ONCE
  x86/gup: Replace ACCESS_ONCE with READ_ONCE
  x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
  mm: replace ACCESS_ONCE with READ_ONCE or barriers
  kernel: Provide READ_ONCE and ASSIGN_ONCE

Pull clk framework updates from Mike Turquette:
 "This is much later than usual due to several last minute bugs that had
  to be addressed.  As usual the majority of changes are new drivers and
  modifications to existing drivers.  The core recieved many fixes along
  with the groundwork for several large changes coming in the future
  which will better parition clock providers from clock consumers"

* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
  clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
  ARM: OMAP3: clock: fix boot breakage in legacy mode
  ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
  clk: Really fix deadlock with mmap_sem
  clk: mmp: fix sparse non static symbol warning
  clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
  clk: change clk_debugfs_add_file to take a struct clk_hw
  clk: Don't expose __clk_get_accuracy
  clk: Don't try to use a struct clk* after it could have been freed
  clk: Remove unused function __clk_get_prepare_count
  clk: samsung: Fix double add of syscore ops after driver rebind
  clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
  clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
  clk: samsung: remove unnecessary inclusion of header files from clk.h
  clk: samsung: remove unnecessary CONFIG_OF from clk.c
  clk: samsung: Spelling s/bwtween/between/
  clk: rockchip: Add support for the mmc clock phases using the framework
  clk: rockchip: add bindings for the mmc clocks
  clk: rockchip: rk3288 export i2s0_clkout for use in DT
  clk: rockchip: use clock ID for DMC (memory controller) on rk3288
  ...