- 20 11月, 2008 1 次提交
-
-
由 Martyn Welch 提交于
The Marvell PHY driver is currently being used for the 88E1111 on the SBC610. This driver is causing the link to run in 10/Half mode, the generic PHY driver is correctly configuring the PHY as 1000/Full. Edit default config to use generic PHY driver. Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 09 11月, 2008 1 次提交
-
-
由 Kumar Gala 提交于
unset CONFIG_PCI_LEGACY in the defconfigs as none of them enable ISDN drivers which seem to be the only place we are using pci_find_device Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 14 10月, 2008 1 次提交
-
-
由 Timur Tabi 提交于
Because CHRP and PMAC are by default enabled, several non-CHRP and non-PMAC PowerPC defconfigs will have these Kconfig options set erroneously. Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 16 9月, 2008 1 次提交
-
-
由 Martyn Welch 提交于
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). This is the default config file for GE Fanuc's SBC610, a 6U single board computer, based on Freescale's MPC8641D. Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 21 8月, 2008 1 次提交
-
-
由 Kumar Gala 提交于
Since we are updated defconfigs I went ahead and moved the asp8347_defconfig under 83xx/ and the mpc8536_ds_defconfig under 85xx/ as that is where they should have been to start with. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 09 6月, 2008 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 17 4月, 2008 2 次提交
-
-
由 Paul Gortmaker 提交于
This adds a sample defconfig for the Wind River SBC8641D board, with SMP, PCI and NFS root enabled. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Board specific defconfigs are useful, however with the ability to do multi-board defconfigs they aren't needed in the top level configs directory Move the 83xx/85xx board specific defconfigs to individual directories under arch/powerpc/configs. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 24 3月, 2008 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 28 1月, 2008 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 06 12月, 2007 1 次提交
-
-
由 Paul Mackerras 提交于
This updates all the defconfigs in arch/powerpc/configs except iseries and ps3, which were updated by the preceding commits. This mostly takes the defaults, except that I turned on tickless idle and high-resolution timers for everything, and turned off instrumentation support and "Fair group CPU scheduler" for the smaller/embedded platforms. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 21 11月, 2007 1 次提交
-
-
由 Kim Phillips 提交于
Now the rtc class ds1374 driver has been added, remove the old rtc driver hookup code, add rtc node to device trees, and turn on the new driver in the defconfigs. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 17 10月, 2007 1 次提交
-
-
由 Anton Blanchard 提交于
When checking out the new NO_HZ support in powerpc, I noticed we never slept for more than 2 seconds. It turns out SLAB has a 2 second per cpu timer that causes this. After switching to SLUB I see some nice 4 second sleeps which is the limit on this POWER6 box (the decrementer ticks at 512MHz): slept 4.19 sec slept 4.19 sec slept 4.19 sec slept 4.19 sec slept 3.96 sec slept 3.80 sec slept 2.99 sec Since SLUB is now the default and some powerpc defconfigs already enable it, lets enable SLUB across the board for consistency. While doing this I also noticed that the maple defconfig has SLAB debugging enabled which is sure to make your box nice and slow. Fix that too. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 30 8月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 23 7月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Added the PCIe device node to the 8568 dts and the needed quirk entries. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 02 7月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 18 2月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Renamed the MPC8568 MDS platform code to follow other 85xx boards. There isn't anything specific about the 8568 MDS code that wouldn't apply to another 85xx MDS system at this point. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 14 2月, 2007 1 次提交
-
-
由 Andy Fleming 提交于
Add defconfig for the MPC8568 MDS reference board Signed-off-by: NAndrew Fleming <afleming@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 10 2月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
The MPC834x SYS board has always been called the MPC834x MDS since its public release. Removed all references to SYS and replaced with MDS. Additionally renamed the .dts to match the defconfig (mpc834x_mds*). Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 26 1月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Updated MATH_EMULATION depends to be on PPC_MPC832x instead of PPC_83xx. Only the the MPC832x has no floating point unit in the core. Updated the other 83xx defconfigs that got math emulation turned on incorrectly. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 22 1月, 2007 1 次提交
-
-
由 Paul Mackerras 提交于
Mostly took the defaults, except tried to get the netfilter options more or less as they were before. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 10 9月, 2006 1 次提交
-
-
由 Paul Mackerras 提交于
Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 30 8月, 2006 1 次提交
-
-
由 Kim Phillips 提交于
This fixes MPC834x MDS (formerly SYS) and ITX platform code to get IRQ data (including PCI) from the device tree, and to use the new IPIC code. renamed defconfig (sys -> mds), left one redundant NULL assignment in mpc83xx_pcibios_fixup to keep the compiler happy. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NLi Yang <leoli@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 16 3月, 2006 1 次提交
-
-
由 Paul Mackerras 提交于
Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 14 1月, 2006 1 次提交
-
-
由 Kumar Gala 提交于
Add the first MPC83xx board that uses a flat device tree to arch/powerpc. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 09 11月, 2005 1 次提交
-
-
由 Kumar Gala 提交于
MPC834x uses the gianfar network driver which now uses the new phylib. We need to update the platform code to create a gianfar platform MDIO bus and pass the right intializations to the gianfar driver to make things work again. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-