This patch adds support to STiH410 SoC.

Please note "st,stih410" is already present in device tree.
The problem is that it is missing the entry in the match table,
and so the L2 cache and other cpus than 0 don't get initialized.
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: NMaxime Coquelin <maxime.coquelin@st.com>
Acked-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

I upgraded my u-boot and noticed that wl12xx stopped working.
Turns out the kernel is not setting the quirk for the MMC2
copy clock while the eariler bootloader I had was setting it.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable TWL4030_USB which is used at least on Nokia N900/N950/N9 (OMAP3)
and BeagleBoard.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.

[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.

Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);

[    1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[    1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[    1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: NMatt Porter <mporter@konsulko.com>
Acked-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.

Fixes: 4da1c677 ("add tbclk data for ehrpwm")
Signed-off-by: NVignesh R <vigneshr@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.

Fixes: 9e100eba: ("Fix ehrpwm tbclk data")
Signed-off-by: NVignesh R <vigneshr@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes 85dc74e9 (ARM: dts: omap5 clock data)

On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.

This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck

Fix this by adding another mux clock as parent in bypass mode.

This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:

DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: NRavikumar Kattekola <rk@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes: ee6c7507 (ARM: dts: dra7 clock data)

On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.

This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck

Fix this by adding another mux clock as parent in bypass mode.

This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:

DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: NRavikumar Kattekola <rk@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Because writing the MOR register requires the PASSWD(0x37),
if missed, the write operation will be aborted.
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Linux may be used without MMU on atmel SoCs, fix debug in this configuration.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The HiSilicon HiP04 has 16 CPUs. I propose we increase the maximum number of CPUs to 16 to avoid the following warning identified during automated boot testing [1].

------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../arch/arm/kernel/devtree.c:144 arm_dt_init_cpu_maps+0x118/0x1e8()
DT /cpu 9 nodes greater than max cores 8, capping them
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-00528-gbdccc4ed #1
Hardware name: Hisilicon HiP04 (Flattened Device Tree)
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (dump_stack+0x78/0x94)
[] (dump_stack) from [] (warn_slowpath_common+0x74/0xb0)
[] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40)
[] (warn_slowpath_fmt) from [] (arm_dt_init_cpu_maps+0x118/0x1e8)
[] (arm_dt_init_cpu_maps) from [] (setup_arch+0x638/0x9a0)
[] (setup_arch) from [] (start_kernel+0x8c/0x3b4)
[] (start_kernel) from [<10208074>] (0x10208074)
---[ end trace cb88537fdc8fa200 ]---

[1] http://storage.kernelci.org/mainline/v3.19-528-gbdccc4edeb03/arm-multi_v7_defconfig/lab-tbaker/boot-hip04-d01.html

Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NTyler Baker <tyler.baker@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The a80 optimus has 8 CPUs. I propose we increase the maximum number of CPUs to 8 to avoid the following warning identified during automated boot testing [1].

------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../arch/arm/kernel/devtree.c:144 arm_dt_init_cpu_maps+0x110/0x1e0()
DT /cpu 5 nodes greater than max cores 4, capping them
CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-00528-gbdccc4ed #1
Hardware name: Allwinner sun9i Family
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (dump_stack+0x74/0x90)
[] (dump_stack) from [] (warn_slowpath_common+0x70/0xac)
[] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40)
[] (warn_slowpath_fmt) from [] (arm_dt_init_cpu_maps+0x110/0x1e0)
[] (arm_dt_init_cpu_maps) from [] (setup_arch+0x634/0x8d4)
[] (setup_arch) from [] (start_kernel+0x88/0x3ac)
[] (start_kernel) from [<20008074>] (0x20008074)
---[ end trace cb88537fdc8fa200 ]---

[1] http://storage.kernelci.org/mainline/v3.19-528-gbdccc4edeb03/arm-sunxi_defconfig/lab-tbaker/boot-sun9i-a80-optimus.html

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NTyler Baker <tyler.baker@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Make sure socfpga_cpu1start_addr is properly flushed from it's cache line so
that secondary cpu's can see it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

socfpga.dtsi is missing the DMA channels for the uart nodes.
This will produce the following errors:

	of_dma_request_slave_channel: dma-names property of node '/soc/serial0@ffc02000' missing or empty
	ttyS0 - failed to request DMA

Provide the correct DMA channels to fix this.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

Correct SCU virtual mapping that was causing this BUG message:

"BUG: mapping for 0xfffec000 at 0xfffec000 out of vmalloc space"
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

Since turning on idle-halt in commit fe46aa67 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: NMichel Marti <mma@objectxp.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet
support for the at91rm9200.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Recent distributions and userspace tools after 2009/2010 depend on
the existence of /sys/class/block/, and will not work with this option enabled.
Signed-off-by: NAnthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Corrected pins used by usart3.
Signed-off-by: NJonas Andersson <jonas@microbit.se>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: NAlexander Stein <alexanders83@web.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

On some platforms, there are multiple SRAM nodes defined in the device tree but
some of them are disabled, leading to allocation failure. Try to find the first
enabled SRAM node and allocate from it.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

at91rm9200 standby and suspend to ram has been broken since
00482a40. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.

Use the correct at91_ramc_base[0] instead.

Fixes: 00482a40 (ARM: at91: implement the standby function for pm/cpuidle)
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The DDRSDR controller fails miserably to put LPDDR1 memories in
self-refresh. Force the controller to think it has DDR2 memories
during the self-refresh period, as the DDR2 self-refresh spec is
equivalent to LPDDR1, and is correctly implemented in the
controller.

Assume that the second controller has the same fault, but that is
untested.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Removed timeout on XTAL, PLL lock and Master Clock Ready, hang if
something went wrong instead of continuing in unknown condition. There
is not much we can do if a PLL lock never ends, we are running in SRAM
and we will not be able to connect back the sdram or ddram in order to
be able to fire up a message or just panic.

As a bonus, not decounting the timeout register in slow clock mode
reduce cumulated suspend time and resume time from ~17ms to ~15ms.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: NWenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This was incorrectly reading the irq status registers during the save
and clear, instead of the irq enable. This worked because there is only
one user for the prcm interrupts currently, namely the io-chain. Whenever
the function was called, an io-chain interrupt was both pending and
enabled.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Deasserting hardreset increases the usecount for the hwmod parent clockdomain
always, however usecount is only decreased at end in certain error cases.
This causes software supervised clockdomains to remain always on, preventing
idle. Fixed by always releasing the hwmods clockdomain parent when exiting
the function.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Tested-by: NCarlos Hernandez <ceh@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This patch fixes wrong hwirq of RTC irq for Exynos3250 SoC. When entering
suspend state, 'enable_irq_wake fail' happen because of the mismatch of RTC hwirq.

[  429.200937] Freezing user space processes ... (elapsed 0.002 seconds) done.
[  429.203383] Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
[  429.209914] Suspending console(s) (use no_console_suspend to debug)
[  429.370685] wake enabled for irq 65
[  429.370837] wake enabled for irq 64
[  429.370868] wake enabled for irq 79
...
[  429.372120] s3c-rtc 10070000.rtc: enable_irq_wake failed

Fixes: a4f582f5 (ARM: EXYNOS: Add exynos3250 suspend-to-ram support)
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

During CPU shutdown the exynos_cpu_power_down() is called after
disabling cache coherency and it uses LDREX and STREX instructions (by
calling of_machine_is_compatible() -> kobject_get() -> kref_get()).

The LDREX and STREX should not be used after disabling the cache
coherency so just use soc_is_exynos().

Fixes: adc548d7 ("ARM: EXYNOS: Use MCPM call-backs to support S2R
on exynos5420")
Reported-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The patch adds domain definition and references to it in appropriate devices.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
[mszyprow: rebased onto generic power domains dt bindings]
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Mixed block needs to control hdmi clock to properly perform power on/off
operation, so add 'hdmi' clock also to mixer nodes.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds configuration of hw modules required to enable HDMI
support on Universal C210 board.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds nodes specific to Exynos4412 based Odroid X/X2/U2/U3
boards required for enabling HDMI display.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

TV Mixer needs both TV and LCD0 domains enabled to be fully operational.
This dependency is modelled by making TV power domains a sub-domain of
LCD0 power domain.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>