- 22 5月, 2008 1 次提交
-
-
由 Ivo van Doorn 提交于
The tx_status enumeration was broken since the introduction of rt61pci. That driver uses different values to report the status of the tx action. This would lead to frames that were reported as success but actually failed to be send out, or frames that were neither successfull or failure which were reported as failure. Fix this by change the TX status reporting and more explicitely check for failure or success. Note that a third possibility is added "unknown". Not all hardware (USB) can report the actual TX status, for rt61pci some frames will receive this status because the TXdone handler is never called for those frames. This unknown will now be handled as neither success or failure, so we no longer increment the failure counter while this conclusion could not be determined from the real status of the frame. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 01 3月, 2008 3 次提交
-
-
由 Ivo van Doorn 提交于
Recent changes to the rate structure registration broke rt2x00, the hw_value was reduced from 32bits to 16bits while rt2x00 used the full 32bits. However the way rt2x00 used the value was inflexible and needed to be changed anyway. This patch creates a array containing information for each rate, the hw_value passed to mac80211 is the index value for that array including a field to indicate if short preamble should be enabled. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
This introduces a big queue handling overhaul, this also renames "ring" to "queues". Move queue handling into rt2x00queue.c and the matching header, use Kerneldoc to improve rt2x00 library documentation. Access to the queues is now protected under a spinlock, this to prevent race conditions which could corrupt the indexing system of the queue. Each queue entry allocates x bytes for driver/device specific data, this cleans up the queue structure significantly and improves code readability. rt2500usb no longer needs 2 entries in the beacon queue to correctly send out the guardian byte. This is now handled in the entry specific structure. rt61 and rt73 now use the correct descriptor size for beacon frames, since this data is written into the registers not the entire TXD descriptor was used but instead of a subset of it named TXINFO. Finally this also fixes numerous other bugs related to incorrect beacon handling or beacon related code. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 2月, 2008 1 次提交
-
-
由 Ivo van Doorn 提交于
This adds 2 new states which both are used to toggle the RX. These new states are required for usage inside the link tuner thread, because the normal RX toggling will stop the link tuner thread. While it is possible that the link tuner thread itself is the caller of the RX toggle (when using software antenna diversity). Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 10月, 2007 2 次提交
-
-
由 Ivo van Doorn 提交于
All drivers use the same values for TSF sync, this will move the value determination into rt2x00config.c, and the definition for the values to rt2x00reg.h Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-