Different paths of the i2400m SDIO driver need to take care of a few
SKU-specific quirks. For the ones that are common to to all the
iwmc3200 based devices, introduce i2400ms->iwmc3200 [set in
i2400ms_probe()], so it doesn't have to check against the list of
iwmc3200 SKU IDs on each quirk site.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

When trying to enable the iwmc3200 WiMAX SDIO function, we loop
waiting for the top controller to be up and running (at which point we
can succesfully enable the function). Between each try we wait for
I2400MS_INIT_SLEEP_INTERVAL ms.

Integration tests have found the current value of 10ms to be too
short; it was upped to 100ms to give more time to the top controller
to be ready.
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The default SDIO IOE wait timeout returned from iwmc3200-wimax's CCCR
is not efficient. This inefficiency will actually cause problems on
Moorestown platforms (system hang).

This is a sillicon bug that requires a software patch to by
overwritting func->enable_timeout. The new value I2400MS_IOR_TIMEOUT
is recommended and verified from the system integration results.

Future sillicon releases will have this default value corrected in the
future.
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

In i2400m-based devices, the driver's bootloader will retry to load
the firmware when things go wrong. The driver currently has a constant
(I2400M_BOOT_RETRIES) which governs the max number of tries.

However, different SKUs of the same hardware may admit or require
different numbers of retries due to it's particulars, so it is made a
BUS specific parameter and different values are assigned for 5x50
devices versus the 3200 ones.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The current SDIO code was working in polling mode for boot-mode
(firmware load) mode. This was causing issues on some hardware.

Moved all the RX code to use a unified IRQ handler that based on the
type of data the device is sending can discriminate and decide which
is the right destination.

As well, all the reads from the device are made to be at least the
block size (256); the driver will ignore the rest when not needed.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

This reset type causes the WiMAX function to be disabled and
re-enabled, which will force the WiMAX device to reset and enter boot
mode.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>

This contains the common function declaration and constants for the
SDIO driver for the 2400m Wireless WiMAX Connection and it's debug
level settings.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>